To add gloss, exclusivity and chic, to make an unusual accent in the interior, you can use the original table. And no one will guess that this piece of furniture used to be an unsightly ruin.

Restoration methods

There are many ways to improve, decorate and restore old table. But before starting work, it is necessary to prepare the future “canvas” - remove the old coating, sand it, tighten all the nuts and screws (so that it does not stagger and hang out), putty, cover with stain (if necessary) or varnish. Then start decorating. Conventionally, all methods of decorating a wooden table can be divided into two groups:

Surface painting, including self-painting, coloring through a stencil or using stamps;

Surface pasting special materials - wallpaper, self-adhesive film, decoupage with napkins or interesting clippings, pasting with a leaf, photo printing, the use of mosaics or tiles.

The glass table will have to be updated a little differently. It is quite possible to glue it with wallpaper, film or decoupage from the inside.

And you can paint with special paints glass surface and get an interesting design.

How to update a glass table?

A beautiful glass coffee table can often be found in modern apartments. As a result improper care glass top loses its attractive appearance.

The legs are loosened, chips and scratches appear on the glass. If scratches have formed on the countertop that can fit a nail, then it is better to give the table to a special workshop, dispose of it or replace the glass with a new one.

If the damage is not so terrible, then you can try to reanimate this piece of furniture.

You can save a glass countertop from scratches at home as improvised (toothpaste, soda, transparent nail polish), and by special means(GOI paste, car polishes, polishing agents for precious metals).

First you need to clean the surface, then gently rub or apply the composition into the scratch. Do not overdo it, otherwise, instead of one scratch, you can get several more. Wait a little for the composition to set and clean the glass again.

To get rid of scratches, use the most ordinary, non-gel toothpaste. Soda is dissolved with water to the state of slurry, approximately in a ratio of 1: 1. GOI paste must be used proven, real. Clear varnish will not completely eliminate the problem, but only partially. At a certain angle of illumination, it will be noticeable that there were scratches in that place.

Wobbling table legs are also repairable. Usually, table legs are attached with special glue. This glue may dry out over time. It can be removed and replaced with a new adhesive. If the legs are attached to screws, self-tapping screws, then they can be untwisted and replaced with new ones.

Now the table can be given a completely new sound with the help of various decorating techniques:

Paste the table from the wrong side with a decorative film. When pasting the table with a film, do not allow the formation of bubbles. It is better to glue the film little by little, gradually moving the substrate away. If bubbles still appear, then you can pierce them with a needle and smooth them out;

Make decoupage. To do this, you will need pictures (for example, from napkins or on rice paper, or images specially prepared for this), PVC glue or special for these works, brushes, a file, decoupage varnish. The necessary equipment can be purchased at craft and scrapbooking stores;

Paint with stained glass paints. acrylic outline, stained glass paints, cotton buds and napkins, alcohol for degreasing the surface, a sketch of a drawing, adhesive tape - this is a set of items that will be needed for this work;

Fix the backlight around the perimeter of the table, led strip;

If the design allows, make a mini-garden, an aquarium or a bright composition of stones, shells. When the table has a small box that is covered with a tabletop on top, you can lay a pallet on its bottom and plant succulents there (plants that do not need frequent watering). Or decorate the box with shells, stones or other things.

How to restore a wooden table?

Wooden table can be made from MDF or chipboard, or from solid wood. In any case, the restoration of the old table at home will take place in several stages. Let's take a look at all these steps.

Preparatory- check all fastenings, disassemble the table and re-fix, clean the surface.

Removing the old cover. Sometimes it just takes special composition, which removes varnish, paint. But most often you also have to use coarse-grained and fine-grained sandpaper, grinder. You need to sand along the fibers, in order to avoid the formation of new scratches.

Repair of cracks and chips. To do this, you need wood putty or a polyester equivalent. After puttying, re-sanding. At this stage, you can stop and not carry out further work (except for varnishing), cover the wood with stain, which will give the table new color and view. For example, turn an oak table into an imitation of wenge or another type of wood. But when the damage is significant, the next stage is necessary.

Priming and subsequent puttying. Without a primer, the varnish will lie poorly and unevenly. For wood fit alkyd or shellac primer.

Giving the final design. At this stage, painting, pasting the table is carried out. If the table is to be painted, the paint must be applied in at least 2 coats.

Final coating with varnish or wax. Lacquer and wax must be covered in several layers.

This refurbished polished table will last for years to come.

Written or magazine, children's or toilet - regardless of its purpose, it will become an interior decoration, because you spent so much time on it and put your soul into it.

How to repaint?

Table painting is the most popular way of restoration. What could be more concise than white table? Only black. Therefore, the choice of paint (acrylic or oil, enamel) is very important. It depends on what kind of paint the repair was made, or rather on its characteristics, how long the restored table will last.

To choose the paint, you need to understand where and how the table will be used, what materials it is made of.

Water-dispersion acrylic paint suitable for heated rooms, withstands moisture well. Dries quickly. Can be washed off with water during application. But after drying, it is not affected by water. Alkyd compounds are considered more reliable.

Oil paints lose their popularity due to unreasonably high consumption.

Enamels for wood attract with their glossy surface and high performance. Nitro-enamel paints also set quickly.

The paint is selected and purchased, further repair of the table involves painting it.

Surfaces must be pre-treated, cleaned, old coating removed, scratches and chips removed, puttied, primed, decorative inserts, such as glass, protected with adhesive tape. And only after the primer has dried, you can paint.

To give an even color, the paint is applied in several layers. The first layer is actually rubbed into the surface.

Two or three coats is enough to bring out the rich color.

To apply an additional pattern to the tabletop, you can use pre-prepared stencils or the most common tulle. When the base color has dried, the tulle (or stencil) is fixed and the pattern is painted. You can do this with a brush, but it is better to use a sponge or a can of paint. Ready product, to give greater aesthetics and strengthen the surface, varnished.

To give a graphic pattern (lines, zigzags, rhombuses, squares), you can use adhesive tape. Mark the future drawing with adhesive tape, apply the first color with paint. If necessary, repeat the procedure with other colors. Varnish the finished tabletop.

If it is necessary to achieve the effect of aged wood, then first a special composition is applied to the treated surface (cleaned, sanded and primed).

Patination can be done with a dark stain. Then the first layer of paint is applied to the tree. Then a second layer of lighter and more liquid paint is applied. When the paint is dry, go over the surface of the sandpaper. Desired effect reached.

The table is ready for top coat varnish.

We update the plastic table

Many are afraid to start decorating plastic table because of its material. In fact, the plastic surface is a more grateful material for restoration. It does not require preliminary and long-term processing.

The maximum is getting rid of scratches and chips. Well, if the surface is even, then it is enough to sand it a little to roughen it, paint or primer could better adhere, or degrease for further work - gluing films, wallpapers, tiles, mosaics, eggshell or decoupage.

To decoupage a plastic table, you will first need to process the countertop. Sand it down, put it down acrylic primer. Then think about how you will arrange the drawings. Make small outlines of their future location. Usually, napkins or drawings on rice paper are used for decoupage, but for these purposes, you can use any clippings and even pictures printed on a printer.

At the end of the work, the tabletop is varnished.

For effective decoupage, you can use fabric. For decorating purposes, cotton material with a bright pattern is suitable. The decoupage procedure is the same, only PVC glue is applied immediately to the entire fabric.

Decor options

Restoration and subsequent decoration of the table is a very long process. But the result is worth it, because you can get an exclusive designer thing with which memories are already associated. Furniture decor can be completely original and at the same time very organically fit into the concept of using the object and the room.

For a table-book or folding table, a laconic design is suitable. It can be dyed in one or two colors. And you can give nobility and accentuate the natural structure of the tree.

If you own an old table that needs to be updated, or you have purchased a table that looks very dull and you want to decorate it with something, then the tips below are just for you!

In fact, changing the look of a piece of furniture like a table is quite easy. And there are many ways in which this can be done.

Adhesive tape

Let's start from the very easy way- This is the use of self-adhesive film. Surely you have seen such a film in stores. It is sold, as a rule, in rolls, like wallpaper.

At the same time, it has smooth surface, which is easy to wash and which simply cannot be damaged or deformed in any way.

To get started, take measurements at home - exactly how much you will need to purchase this film. Take it a little with a margin so that there are no ugly joints on your table.

The very process of applying self-adhesive film is very simple - there is no need to prepare furniture before that. You simply separate the film from the paper and apply it to your table, gently pressing it against the surface.

The table does not even have to dry. It will immediately be ready for use in an already updated form.

Paint and stencils

If you're ready to mess with a little more than glue self-adhesive film on your piece of furniture, you can, armed with paints and a brush, appear in the image of a graphic designer.

The most important thing is to come up with a plot for your table. Think about what you would like to depict on it? It can be anything you wish. If you have the makings of an artist, you can start painting right away, with or without a sketch.

Note! Cape on the sofa - what should it be? 100 photos of fashionable novelties and design!

But if you are “on you” with art, do not despair! Stencils will come to the rescue. You can buy a stencil in the store stationery or make your own.

To do this, it is enough to cut out a drawing from a magazine and use it as a kind of template, according to which this drawing will be transferred to your furniture.

Or draw any of the objects you like with a pencil on a sheet of paper, cut it out and, putting it on the table, paint over the gap of the cut out stencil with paint. After removing the stencil, you will see the drawing on the table.

If this method seems difficult to you, you can seek the help of a professional artist, for whom this type of work will not be difficult.

True, the services of the artist will need to be paid for and this method can no longer be called budgetary.

As for the paint that should be used, it must be moisture resistant. Most the best option considered acrylic paint. It is odorless and dries very quickly.

In addition, acrylic does not fade in the sun, is resistant to water and high humidity generally.

We can safely say that a table covered with acrylic paint will last you a century, and this will not be an exaggeration.

Decoupage

There is another way to decorate the table, which is very similar to using stencils. This method is simply called decoupage. What is it?

Any fragments of drawings from magazines, napkins, various albums are taken. It can even be photos from your personal archive or just pictures you like from the Internet.

In general, anything. You cut out the elements you are interested in and put them on the countertop. First, see if it looks nice. If you like the option and you are ready to decorate the table with these fragments, then you can get to work.

A piece of furniture must be carefully sanded, removed paint or disposed of varnish coating. The surface of the table must be clean, dry and perfectly flat. In general, it should return to its original appearance.

After that, you take pre-prepared elements or photographs, cover the back with PVA glue and put them on the countertop.

Such manipulations must be done with each photo. After that, you should cover all the superimposed pictures with varnish.

The varnish will prevent your table from unwanted damage, scratches and other kinds of deformations. Your photos (decoupage) will be under reliable protection. At the same time, table decoration will not only update it, but will also delight your eyes!

There are many table decor options. Most importantly, don't be afraid to experiment! And you will definitely succeed.

Photo ideas for decorating the table

Beloved good old furniture you can give a second life. To make a table decor with your own hands, you should try a little, listen to the advice of experts and show your imagination. The result of the decor is guaranteed to exceed all expectations.

Preparation for work

In order for the work to go quickly and to be of high quality, it is necessary to determine what material the table was originally made of.

• Wooden crafts. To clean the table of old paint with your own hands, you need to prepare tools such as a chisel, sharp knife, spatula, sometimes a planer can be useful for completely leveling the countertop. Old paint can be removed using these tools (it is also possible to remove paint with acetone, solvent, etc.), rub it with sandpaper until smooth, even out cracks with putty, thoroughly soak with an antiseptic, cover with a primer and let the countertop dry.
• Hardware. Delete old paint with your own hands from metal, you can use special liquids like a solvent. You can get rid of rust on the countertop with a converter or use cola or vinegar at home. Any of these liquids should be applied to the surface and held for 20 minutes, then carefully removed.

Decoration methods

There are a lot of options on how to decorate products made of old wood or metal. The final result of the decor can be seen in the photo.

Adhesive tape

The easiest way to make an original practical table with your own hands is to paste over its countertop with a film, the assortment of which is quite diverse in construction stores. The self-adhesive film must be glued to the countertop, pressing firmly and rubbing it thoroughly so that there are no wrinkles and bubbles, and the pattern is not distorted.

The manufacture of such a table is the fastest in terms of time, because. does not require long drying. You just need to get used to it a little and not immediately remove the film, trying to stick it to the entire surface. It is recommended to gradually unwind the roll, processing small areas, gradually covering the entire surface of the countertop.

For better fixation of the "self-adhesive" on the ends of the countertop, the material is dried with a hairdryer

Mosaic

The decor of the countertop can be done by decorating with mosaics. It can be made from fragments old tiles, glass, pieces of discs and other small pieces of materials at hand. To do this, it is necessary to process the countertop in a way suitable for wood or metal, let it dry and cover it with PVA glue. Pieces of materials should be laid out arbitrarily in the form of a pattern or ornament and left to dry completely. Then open several times with varnish until the surface is perfectly smooth.

Ceramic tile

Table decoration can be done using the tiles left over from the previous repair. It can be plain or with a specific pattern. To do this is quite simple in the usual way of gluing tiles with special glue. At this method decor opens an extraordinary flight for the imagination. You can lay out the tiles in one or more rows, make an original pattern over the entire countertop, mark the corners or go around the perimeter. In any case, it will be practical, especially if the table is outdoors on the site.

Decorative tape

A very simple and original idea will be an update kitchen table with their own hands, pasted over with decorative tape. This easy-to-use decorative material can be combined in color to create a unique pattern to suit your taste. The technique of pasting with adhesive tape is similar to the process of decorating countertops with self-adhesive film. See above.

Epoxy resin

Decor will be very impressive. dining table made with epoxy paint. This liquid solidifies and turns into transparent plastic, filling cracks and depressions on the countertop. To create original drawings on the table, you can put small flowers, pebbles, shells and other small items in these dimples at your discretion. This creates the effect of frozen time in compositions reminiscent of amber, but without the characteristic orange color.

Glass decor

For a table reminiscent of an exposition of a local history museum, suitable original decor under glass. To do this, you need to make a recess of any geometric shape and fill it with shells, colored sand, dried marine life in the form of stars, hedgehogs, etc., as well as dry flowers, pebbles or glass fragments. Then cover the recess with glass of a similar shape.

Tulle decoration

The design of the table, made by staining through tulle, will look very gentle and elegant. To do this, firmly attach the tulle to the surface and carefully cover the table with spray paint. Then very carefully remove the material. It should be remembered that the part covered with tulle will have the original color of the table, and the background will be painted with spray paint. Based on this, it is initially worth deciding on the shade of the openwork pattern and coloring the table with it. Only after complete drying is it recommended to start attaching the tulle and further decorating the tabletop.

To decorate using the stencil technique, you will need an old tulle or unnecessary lace napkins (after decorating, they will have to be thrown away)

Gilding

For making a decorated dining table or coffee table with your own hands, you can apply an exquisite way of decor - gilding. This can be achieved by painting the countertop with paint with a gilding effect, or by applying gold leaf. This thin foil is cut out with scissors and glued to the table surface using PVA glue. Then they wait for complete drying and cover with a colorless varnish. The golden pattern will perfectly complement the set, made in classical style. If desired, you can arrange all the furniture in this way.

Decoupage

To design a drawing in a decoupage way, it is necessary to cut out the drawings you like from napkins, carefully remove the bottom layer of paper and attach the cutouts to the surface in the design that you liked the most. Then dip the brush into the PVA glue and lightly smear the top. In this case, it is necessary to take care of a uniform snug fit of the pattern to the table so that there are no folds and irregularities. If the paper is wrinkled, gently wipe it with a sponge or a soft, lint-free cloth that has been moistened with warm water and repeat the decoration process again. After complete drying, cover the surface of the countertop with a transparent varnish. This way of decoration has received a separate recognition of hand-made lovers.

Craquelure

The method of using craquelure varnish helps to achieve the effect of antiquity and antiquity. It is used to age paintings and furniture, which later take on the appearance of cracked and peeling furniture. Work should begin with painting the surfaces in the color that was intended for the veins. Then the craquelure is applied directly, which can be one-step and two-step. When covering the table with one layer, after a while the varnish dries and cracks. Two-step craquelure is different in that it includes a combination of paint with epoxy resin and paints with water base. As a result, after varnishing, cracking occurs and a characteristic surface is formed.

Artistic scribing

This method of decor involves drawing patterns on the surface with a brush and acrylic paints using stencils or tracing paper. To decorate the table by painting, it is necessary to prepare its countertop for production traditional way described above for wood or metal. Then you should apply the drawings in the usual way for the master in any execution. After complete drying, it is necessary to apply one or two coats of varnish with an interval for drying. After 2-3 days the table will be ready for use.

It is very easy to create a unique creation in the form of a table yourself. This work is interesting and fascinating, and the result of the decor will definitely delight and cheer up all the relatives and friends of a real master.

Video: how to quickly and inexpensively transform the kitchen table top.

Self-adhesive film is an excellent finishing material that allows you to inexpensively, quickly and beautifully update furniture that has lost its attractiveness. How to properly glue a self-adhesive film on furniture, the nuances of work, which type is better and how to use it correctly will be discussed in this publication.
Not everyone, for material reasons, can afford to replace the old furnishings with a new set.

Living in a rented apartment in anticipation of acquiring a new home, it is not advisable to spend money on buying a new one.
Contemplation every day of the old environment often spoils the mood, therefore, ideal and inexpensive option to transform its appearance will be pasting with a self-adhesive film. self-adhesive perfect solution for decorating garden furniture.
Manufacturers today produce self-adhesives in a large assortment of types, sizes, textures, characteristics, texture, which will satisfy any wishes.
Used self-adhesive for transformation appearance not only furniture, but also window sills, countertops, doors, windows, platbands, glass, and other interior items.
A wide range will allow you to choose suitable material for all rooms in the apartment. Your task is to choose the right one.

Furniture film selection

The composition of the film is determined by the type of the main polymer component, the plasticizer that gives it elasticity, pigments, and other additives, depending on the type of material.

If we consider how to properly glue a self-adhesive film on furniture, then you need to get acquainted with its main types. There are several types of film, they can be classified according to the following criteria.

Type of film according to the composition of the constituent components

• Polyvinyl chloride (PVC);
• Polyester;
• Propylene.

By type of outer surface

The surface of the film determines its use for furniture different directions, premises, achieving the desired effect in conjunction with overall design generally.

Glossy most appropriate in rooms without daylight, dimly lit rooms located on the north side.

Matte, on the contrary, it will well complement the design of bright and spacious rooms.

transparent used to protect against scratches, cuts, for glass surfaces.

Holographic looks spectacular in any room, creating the effect of "play of light". Shades change depending on the angle of illumination, as well as its visually perceived volume.

Mirror indispensable in small rooms, visually increasing them. With the right combination of color, arrangement of interior items, you can achieve harmony and originality in building the overall design.

By structure

Single layer films are made from a combination of ingredients - various plasticizers, resins, pigments, stabilizers.

Double layer- the name itself suggests the presence of two layers. The bottom (base) is made of paper or fabric. The top layer consists of a certain combination of PVC resins, where the pattern is applied.

Production is carried out according to different methods. When sticking, the film is separated from the base and glued to the surface. How to glue self-adhesive film on furniture is described below.

By decorative design

A huge range of this material has won a great consumer demand. Consumers are offered a wide range of products for furniture finishing different rooms. Big variety colors, types of film allows you to choose exactly your finish.

It is presented in the form:

• imitation of wood of different species;
• natural stone;
• ceramic tiles, mosaics;
• leather, fabric, velor, tapestry, cork, other materials;
• under gold, silver;
• children's motives from fairy tales, cartoons.

Many more can be listed various options. Dress up the furnishings in new clothes, PVC film will help you to give it an updated design, since it is recommended to glue it on furniture.

The main advantages of self-adhesive film

After getting acquainted with the types of film, let's move on to the question of how to properly glue the self-adhesive film on furniture, and outline the sequence of work.

How to stick self-adhesive film on furniture

Preparatory stage:
The base before the sticker must be even, smooth, without roughness, cracks. Fill cracks with putty, sand it. Otherwise, the film will repeat all the flaws of the base and stick badly.
The surface must be cleaned of any kind of contaminants.
Remove the handles - screw them again after finishing work. Glasses, decorative linings, moldings are also temporarily dismantled.
Degrease the prepared base with any dishwashing detergent. Cover the wooden base with acrylic varnish.

cutting material

Before buying self-adhesive, draw a sketch with the dimensions of the elements to be glued. This will help you choose the right size of the material in width (rolls are sold different widths) to have as few joints as possible. Ideally, in small areas, there should be no joints at all.
After acquiring the material, correctly cut it into details on reverse side- there is a marking grid multiple of 1 centimeter, which is very convenient. Cut out each fragment and proceed to the main stage.

Pasting furniture with self-adhesive film

If the pasting element is small, for example, a door from a kitchen cabinet, then here you can glue it dry, and if you need to glue a cabinet with a self-adhesive film, then better foundation moisten with water, soapy water solution.
Then the self-adhesive will not immediately stick firmly, it will be mobile, so you can even out any misalignment. This happens if you glue for the first time.
How to properly glue self-adhesive film on furniture difficult process- the main thing is accuracy, accuracy in measurements, lack of haste.
Glue the canvas should be on top. If these are doors, then they can be removed. Separate the self-adhesive from the protective substrate by 8 - 10 centimeters and apply tightly to the top of the element to be glued. Fix by smoothing this area from the center to the edges with a cloth, pressing well.
The bottom hangs down together with the lining. little by little separate upper layer from the substrate, smooth the glued piece well. So in small sections you go down, removing protective layer, and gluing well, expel bubbles.
Evaluate your work, and if you see bubbles on the surface, then pierce them with a thin needle, squeeze out the air, press this area. If a wrinkle suddenly formed during smoothing, then warm this place with a hairdryer and smooth it again.

Let the film dry if you used water and get used to its new habitat, after which you return the fittings and glass to their place.

How to remove self-adhesive film from furniture

If the self-adhesive was pasted for a long time and began to look untidy, you damaged it, then it is better to remove it and stick a new one.
During the next repair, the old design of the self-adhesive does not harmonize with the rest of the interior, then remove it and change it to a new one.
We examined how to stick a film on furniture, and the principle of removal is based on heating adhesive composition, which then easily separates from the surface.

Remove the sticker with a hair dryer

Use a hair dryer - for small areas, a hair dryer is suitable, and if the area is large, then use an industrial one. Start heating the film and at the same time pull it slowly and carefully so as not to tear it.
Adhesive residue may remain on the base. Remove it with benzine, thinner, alcohol, white spirit or other. It all depends on the base material. In order not to damage the base, try to apply the composition in an inconspicuous area. If everything is ok, then use it.
Proper care
Caring for self-adhesive film comes down to wiping it with a damp sponge. If the stains are greasy, then wash it with liquid detergent.
Do not use powder type products, so as not to scratch it. Solvents can ruin the film, it is better to wipe the dirt with a swab with alcohol.
Pasting furniture is available to everyone - this is a simple, but also a fascinating process. We got acquainted with how to properly glue a self-adhesive film on furniture, it remains to choose the right one and start transforming your apartment.

The old table, if it is still functional, easily turns into a new one. The result may even exceed your expectations, because new table will be brighter, more original and, most importantly, positively charged by your creativity. Stock up on inspiration simple materials and go ahead, embody ideas!

Note before the start: in almost all cases, the table needs to be prepared for transformation. Wipe it with a sandpaper, clean it of dust and degrease with alcohol or special means.

Paint with stripes

Painting is one of the fastest and most effective techniques in furniture decor. To make it more interesting, we suggest making the table striped. Helps you get the job done right masking tape: Paint the table the base color, then stick on some strips of duct tape and apply a couple of coats of another color. Peel off the tape - the effect is ready. Can be repeated many times to make stripes of different colors and widths. Do not forget to varnish everything for reliability. TIn the same way, you can create zigzags, for example.

Paint with slate paint

Painted with a special slate paint the table will be laconic black or dark green. But now you can leave notes and draw with crayons right on the table. How easy is it to play board games where you have to record points! The table itself can serve as a field for tic-tac-toe or a gallows.

Paste over with a film

The film can also be not simple, but slate or even with the effect of white marker board. Over a table with a pattern of triangular pieces of film, as in the photo below, you will have to tinker longer, but the result will be very stylish!

Stripes with colored tape

A striped table can be made not only with the help of painting. Lines of decorative tape or electrical tape in different colors and patterns will make the table bright, shiny and elegant. This is perfect for a nursery or will add a touch of mischief to an adult interior.

tile

Ceramic tile or mosaic will make the countertop not only beautiful, but also very practical, because the tile is not afraid of moisture and is easy to clean. The principle is the same as with walls: tile adhesive plus grout. You can take a whole tile, or you can beat it for the effect of a Spanish mosaic. More ideas creativity from the remnants of tiles you will find.

Cover with book pages

Choose your favorite book and give it a second life: glue each page to the table with PVA glue. Several layers of varnish (preferably from a can) will make the surface smooth and ennoble the color. It's a good idea to take dictionary pages or sheet music.

romantic lace

A simple technique will help to make the tabletop more elegant - coloring through lace. To do this, you need to take a lace doily or tulle, which you don’t mind ruining, put on the table on top of the base coat of paint and apply a different color on top. It is better to use a sponge or spray paint so that the image does not smear from the movements of the roller.

Photo: californiahomedesign.com, homedit.com, shelterness.com, lovemaegan.com, allthingsnewagain.net, baeditions.com, crafthubs.com, hellolidy.com, getcreativejuice.com