Hello everyone! In this master class, I will show you how to make a simple and light canopy-type canopy over the entrance to your house. Everyone knows the problem when, when it rains, water flows from the roof in a large stream, in addition to the fact that it is raining itself. Just to avoid this, to constantly have a dry threshold in front of the entrance, I propose to build this simple visor over the door from plastic pipes.

It will be needed for manufacturing

• PVC pipes. But no one bothers to do this from polypropylene pipes.
• PVC pipe glue, if you are using PP - PP soldering iron.
• Rectangle made of plexiglass, acrylic, plexiglass or polycarbonate. Any of the above will do.

You will also need another common tool that can be found in any workshop, even the most seedy master.

Making a visor for the house

Decide on the size of the desired visor, estimate the angle of inclination by eye. Ideally, draw a sketch on a piece of paper.
Then select the diameter of the pipes that will be used.
We start assembling. We cut pipes, prepare fittings.

First, we collect two corners:

Then the third side is for these quiet triangles.

We connect the third sides of the triangles with longitudinal guides. This will be the roof to which the transparent acrylic sheet will be attached.

We connect, we get triangles. A longitudinal guide has also been added to the bottom of the visor.

In general, the more guides, the better.
We take acrylic glass.

We fasten it to the frame through rubber-like pads. They are of course not necessary, but thanks to them excess vibration is suppressed, the glass does not enter into resonance, and dripping drops on the glass are not heard at all.

The suburban area is an excellent place for outdoor recreation. If you do not have a place on it, under which you can hide during the rain or midday heat, then you can make the simplest canopy of plastic pipes for the water supply.

It is very easy to mount such a structure, while it will be collapsible. At the end of the season, it can be folded and stored in the barn.

Making a simple pipe structure

To work you will need the following.

1. Two plastic pipes made of polypropylene, polyethylene or PVC, with a cross section of 20 mm.
2. Dense fabric, it is better if it is waterproof.
3. A strip of strong, dense fabric.
4. 4 cut from a steel pipe, with a cross section of 25 mm, about 20 cm long.
5. A needle and thread or a sewing machine.

Getting ready for work

1. First, decide where you will build the canopy.
2. Next, you need to carry out the markup. Keep in mind that the structure will be arched, with an awning stretched over it.

Note!
The best option is to make 4 marks at the same distance from each other.
At the same time, take into account the size of the canopy, which will depend on what kind of furniture will be located under it, and how many people it will have to accommodate.

1. Take 4 pipe segments, their inner section should slightly exceed the outer diameter of the frame elements. Drive them in at the marked points.
2. Do this until areas of 2 cm in height remain above the ground level. The result of your work will be a kind of "sleeves". It will be necessary to insert plastic pipes into them.

Installation of a structure

1. Prepare two cuts from the polymer pipe. Their length can be calculated by presenting 4 as the sum of the required height of the two walls + 1.5, because the top of the frame will have a round shape.
2. Next, you should sew the material that will serve as an awning. The instruction notes that its width should be 1.8 m, because on each side the gap from the fabric to the pipes should be at least 10 cm.

Note!
Especially it should be said about the length of the awning-canvas.
Experts say that it should cover at least 50 percent of the useful area of ​​the plane of the future structure.

1. The prepared piece of material should be hemmed along its edges. Further, along the length of the cut, it is necessary to hem double strips of fabric. Then it will be necessary to pass the frame pipes through them. These elements must be sewn in 10 cm increments.
2. Now you can assemble the canopy. Place the tarpaulin over the pipes first.
3. Next, insert them into the bushings driven into the ground.
4. In this case, the elements of the frame will be bent in the form of arches.

1. Lastly, unfold the awning to the optimum position.
2. The canopy, the price of which is minimal, is ready.

How to make awning fabric water repellent

If you don't have a special moisture-repellent fabric on hand, you can make one yourself. This will give you an awning material that will reliably protect the space inside the canopy from rain.

Below are three easy ways to do this.

1. Stir 250 grams of casein glue and 12 grams of lime in 750 ml of water. In another container, prepare a soapy solution containing 1.5 liters of water and 15/20 grams of laundry soap.
   Combine the liquids and mix well. Dip the canvas into this mixture. Let it soak well, remove, squeeze and let dry.
2. If the material is linen or cotton, dilute 125 grams of gelatin, the same amount of laundry soap and 300 grams of alum in 8 liters of water. Put the solution on fire and bring it to a boil, remembering to stir regularly. Dip the canvas into this mixture, wait 2 hours, then remove and dry without wringing.
3. Crumble 100 grams of baby soap into 3 liters of water and stir. Heat the mixture to 50 degrees and dip the material in it for 30 minutes. Then, twice for 15/20 minutes, soak the cloth in potassium alum (10% solution).

After the procedures, the material must be rinsed in cool water. Then it should be dried.

Ready-made canopies-pavilions

Now manufacturers produce prefabricated arched and rectangular canopies made of polymer pipes.

1. Analogues for a garage, for a pool or as a structure attached to the house, have a width of 3 or 3.5 m. Their frame is assembled from (20 × 20 × 2 mm) in a polyvinyl chloride sheath.
2. Larger structures for play, sports and utility pavilions have a width of 4 or 5 m. Their frame consists of double shaped pipes, also protected from PVC.
3. The length of such a structure can be up to 8 m.

Note!
Thanks to the polymer coating, the service life of the structure is increased, it acquires an aesthetic appearance and reliable protection against rusting.
Two-piece frame arches are easy to transport.

1. There is no need to build a foundation under such a canopy. It is enough to drive a pin 100 cm long into the ground, and put an arc of two elements on it and fix them with a self-tapping screw.

If you decide to purchase and assemble, for example, from a PVC pipe with your own hands, please note that mounting sleeves for the frame supports may also be included in its kit.

Output

Arrangement of a canopy made of plastic pipes does not require capital investment of money and labor from you. As a result, you will get a lightweight structure that can protect you on the site from the sun and rain. The video in this article will reveal more fully its topic.

A greenhouse made of propylene pipes is the simplest greenhouse structure for independent construction. The design is presented in several versions. In order to build such a greenhouse with your own hands, you need to follow the simple step-by-step manufacturing instructions.

Peculiarities

A greenhouse made of polypropylene pipes is an interesting solution with a limited budget and love to build a variety of structures with your own hands. The purchase of materials will not require large financial costs, and the construction will not require serious preparation.

All materials can be bought at an ordinary hardware store; to fasten them to each other, you will need ordinary glue or self-tapping screws.

To begin with, it is worth dwelling on what propylene pipes are and how they differ from PVC. In fact, there is not much difference between these materials. Both one and the other pipes are plastic. The only difference is what polymer they are made of - polypropylene or polyvinyl chloride. This does not affect the operational properties of pipes, the only noticeable difference is in the price.

Polypropylene pipes have a number of advantages.

• Resistant to corrosive processes. Plastic pipes do not rot or rust, unlike other materials.
• Ease of use. Polypropylene pipes can be easily bent or cut. Any intricate wireframe can be created from them. In addition, it is also quite simple to fasten the profiles together and install them in the ground.
• Low weight. Polypropylene pipes are lightweight regardless of whether they are single-layer or multi-layer. This is a guarantee that the whole frame can be easily transferred, and not just disassembled.

• Long service life. Initially, polypropylene pipes are designed for communications, in particular water supply, therefore they are given increased strength. Without being exposed to such loads, pipes can last 30-50 years.
• Strength. In addition to corrosion resistance, such pipes are resistant to temperature extremes. They do not burn, they are not afraid of open fire at all. In addition, the pipe frame will be able to withstand strong winds, especially if the base is reinforced. So, the material does not lend itself to deformation under the influence of various climatic factors.

• Cheapness. Plastic polypropylene pipes belong to the economy segment, therefore, very meager funds can be spent on the purchase of this material.
• Attractive appearance. There is no need to process propylene pipes additionally. They are immediately supplied with a special coating, which not only increases their strength properties, but also gives the raw materials a beautiful shine. As a result, the whole greenhouse on such a frame will look great.

Design options

A structure of almost any complexity can be assembled from polypropylene pipes. Limitations are imposed only by the degree of skill of the one who performs the structures.

The most common forms of homemade greenhouses are:

• arch;
• pointed arch;
• with a pitched roof;
• with a gable roof.

Separately, it should be noted that greenhouses and greenhouses with a pitched roof are usually performed as an extension to the house. Here it is envisaged that one wall will be adjacent. This saves significant heating costs.

The most simple arched structure for construction. There are some designs that can be delivered in just a few hours. However, it is extremely important here what material and how the strapping will be made. After all, the rods form a strong pressure. In addition, such a structure made of polypropylene cannot be made for winter. The snow pressure on the roof will be too strong, and the frame simply will not withstand - it will fall apart.

In this case, the shape of a pointed arch is used. It is a cross between the classic arched and gable designs. Of course, it requires more details and work skills, but the result is beyond praise. A strong plastic frame is able to stand not 3-4 seasons, as usual, but all ten.

Finally, the gable plant house is a common option due to its classic shape. Such a greenhouse will fit into any landscape, suitable for almost any home. You don't need to be an engineering genius to build it.

This design is the most durable, since the frame is reinforced here.

Rules for working with the material

First you need to study the nuances of working with polypropylene pipes. Only after that you can proceed to their installation, collection of the frame, flooring of the coating material. So, first you need to take into account that it is best to work with such pipes at a temperature of + 18-20 degrees. Then the material will gain maximum strength and flexibility, will not "shrink", and it will be easier to form the necessary shapes from it.

The second feature is the need to select fittings for the diameter of an existing pipe. Fittings are connecting elements. With their help, it is possible to achieve optimal rigid fastening of parts to each other. In order for the work to go as smoothly as possible, it is best to purchase pipes already complete with fittings. This eliminates the risk that the connecting elements and pipes do not fit together.

Welding may be required to work with polypropylene pipes. Many do not have a plastic welding machine on hand. Then there is an alternative - a gas burner. It can replace the iron that is usually used for welding. However, you need to act carefully so as not to melt the pipes too much. It should be borne in mind that welding is used only in cases where it is planned to build a capital structure from pipes, which is not planned to be rearranged or removed for the winter in the future. An example is an attached greenhouse with a pitched roof.

Fortunately, no specific protective measures are required when working with polypropylene, as the material is not toxic.

The only thing is that grinding may be required at the place of the saw cut, but this rule is not necessary to follow.

Coating materials

Greenhouse cover with plastic pipes is a special topic. The fact is that, although the frame is relatively strong, it cannot withstand the weight of those materials that are traditionally used for shelter. These include plexiglass, double-glazed windows and some others. Such materials guarantee high protection against drafts, good heat retention even in winter, full access to sunlight, but due to their heavy weight, they have to be abandoned.

Certain requirements are put forward for materials for covering the frame made of polypropylene pipes.

• High thermal insulation properties. This is especially important if the greenhouse is planned to be year-round, working in the winter;
• Good ability to transmit sunlight. An additional feature of the material may be that it filters out harmful infrared radiation, letting in only those rays that are beneficial to plants;

• Resistant to weather conditions. It is important that rain, snow or hail cannot damage the coating material, otherwise the tightness in the greenhouse will be broken and the heat will escape. So, both the greenhouse and the crop will be irretrievably ruined;
• If the greenhouse is year-round, then the coating material must withstand snow, not tear under the snow cap;
• Resistance to mechanical and wind loads is desirable. A gust of wind should not damage the integrity of the coating, as well as minor mechanical impacts. Some materials are able to withstand heavy loads, for example, impacts, without tearing or breaking;
• Light weight.

Thus, the existing list of materials for coating is sharply reduced, because very few materials combine all the listed qualities.

Optimal for frames made of polypropylene pipes are coatings with polyethylene film or polycarbonate plates.

Polyethylene film

Polyethylene film is one of the most demanded materials for covering frames made of polypropylene pipes. This is due to its many advantages.

• Light weight. First of all, you should pay attention to the lightness of the film coating. With a large enough area, a sheet of film can only weigh a few grams. This ensures that a minimum load is applied to the frame.

• Light transmittance. Films are produced either completely transparent or slightly dull, but this does not prevent sunlight from penetrating well through them, illuminating the entire area. You can vary the amount of light entering the greenhouse simply by choosing a film with the desired tint. This allows you to grow any crops in such greenhouses - both shade-loving and light-loving.
• Resistant to weather conditions. Films do not react to changes in ambient temperature from -50 to +60 degrees. They are not afraid of rain, hail, snow and wind. But they will not hold the snow cap.

• Creation of a greenhouse effect. The air in plastic greenhouses is always humid and warm, so the ground in them does not cool down either. This allows you to create the most favorable microclimate in such greenhouses.
• Material safety. Polyethylene does not decompose and does not affect the soil, therefore it does not change its composition. It also does not release hazardous substances into the air. It turns out that the presence of polyethylene does not affect the contents of the greenhouse in any way.
• Cheapness. Film can be bought for a low price or even free. She may even already be on the farm.

Among other things, it has material and its drawbacks. The film does not resist mechanical damage poorly. Any puncture or blow is capable of breaking it, rendering it unusable. It should be borne in mind that such gaps can be easily repaired with ordinary scotch tape. The film quickly breaks down, becomes thinner due to constant exposure to the sun. This coating will last only 2-3 seasons.

Polycarbonate

Another alternative greenhouse cover material is polycarbonate. It is somewhat heavier than the film, so it will be necessary to seal the frame by using composite reinforcement and additional supports. This material has such advantages that more than justify all the inconveniences that arise.

• Good light transmittance. Cellular carbonate, which is commonly used in greenhouses, provides a more durable alternative to glass. You can choose from completely transparent materials, matte or colored.

• Strength. Polycarbonate is resistant to any mechanical stress, be it heavy precipitation, impacts, punctures. It also does not buckle under the weight of the snow on the roof. Water and high humidity are not terrible for polycarbonate, since it does not corrode or deform when exposed to water.
• Plastic. Subject to all the rules, polycarbonate plates can be bent, giving them an arched shape. However, intricate structures cannot be built: the material is still not so flexible.

• Long service life. According to manufacturers, polycarbonate plates do not lose their properties during 20 years of service.
• Interesting appearance. If greenhouses made of film are trivial and almost everyone has, then polycarbonate separates the owner from the gray mass. The greenhouse looks neat and unusual.

Like the film, polycarbonate has its drawbacks. This material is afraid of high temperatures. When exposed to open fire, it begins to melt, and it is not very easy to stop this process. The price factor also plays an important role.

Polycarbonate models are more expensive than film ones, but still not so much as to immediately dismiss this option.

Construction master class

Making a greenhouse from polypropylene pipes is not as difficult as it seems at first glance. In fact, even a teenager who attended labor lessons at school can handle this.

Before you start, you need to do some preliminary work.

• A greenhouse, like any structure, will have to be carefully planned and designed. Without a plan and drawings, it will not be possible to build a truly good greenhouse that has the correct dimensions and proportions. You can draw up a scheme yourself, take a ready-made one or order, but the latter option is not very rational, since an individual sketch will cost more than the entire purchase of materials.

• It is necessary to immediately prepare all the necessary materials and tools. For this, a plan was drawn up: it reflects the location of all profiles and parts, all screws and self-tapping screws, as well as the fixing points of the cladding material. With this information on hand, you can buy everything you need.

The preparation must be thorough. The quality and speed of greenhouse construction in the future depends on how conscientiously it is carried out. Careful preliminary work allows you to design a more serious structure, which has not only a door, but also vents for ventilation. Also, a scrupulous study of details is needed when the greenhouse is not made for seasonal use, but for year-round growing of vegetables and berries. Only then will it be possible to provide for all the nuances, including the correct position of the greenhouse relative to the cardinal points.

Layout

The first step is to decide what size the greenhouse will be. It depends not only on the needs, but also on the size of the site. For example, on an area of ​​100 sq. m, you can easily fit a large greenhouse, while for a small area, only a mini greenhouse is suitable. However, it is worth remembering that polypropylene pipes are still a material that was not originally intended for construction, so you should not make extra-large structures, for example, 8 m wide and 15 m long.For such purposes, it is better to choose a less flexible material.

The optimal solution is a greenhouse with dimensions of 2.5x4 m and a height of 1.9 to 2 m.It should not be done below, since it will be impossible for a person to straighten out there, which will greatly complicate the work of caring for growing crops. Such dimensions will make it possible to plant several beds of various crops in the greenhouse.

For construction, you need to choose the right cross-section of polypropylene profiles. For this, multilayer pipes with a diameter of 20–32 mm, an internal section of which are 16 mm, are suitable.

The length of polypropylene pipes may vary, but for the construction of a greenhouse, options are needed in lengths from 2 to 7 m.

As for the choice of a site for construction, it must meet several requirements.

• Lack of shadow. You should not put the greenhouse in the shady zone, otherwise you will have to abandon the cultivation of light-loving crops: peppers, cucumbers, tomatoes.
• The ability to freely enter and exit the greenhouse. Do not position the door so that it rests against the flower garden or other beds. Leave a small space for convenience.
• The site should not be windy. Inquire about how the winds blow in your area and position the structure in that direction. This is especially true for greenhouses with pitched roofs.

Development of drawings

The drawing is needed not only in order to know exactly how the greenhouse will be located and what is needed for it. The project is also important for budgeting, because knowing the number of elements and their cost, you can quite accurately determine the price for the entire homemade greenhouse.

You can draw up a layout diagram yourself, remembering drawing lessons from the school curriculum. To simplify this process, there are many 3D modeling programs, some of which are free. Some can be used directly online.

The easiest way is to take a ready-made drawing. There, as a rule, the calculation of parts, connecting elements and materials for the coating is immediately provided. It is possible to choose a greenhouse of any size and height, including those whose frame requires reinforcement through reinforcement.

What is the secret of the popularity of polycarbonate awnings? Why is this material chosen more often than others? Is it really all about low cost, or are there other features worth knowing about? How not to be mistaken when choosing a carport for the first time? How might this design look like, and why is it needed at all? We have prepared for you all the necessary information about canopies and canopies made of polycarbonate, and also selected the 50 best photo examples!

Order a canopy?

At the prices there are promotional awnings - a carport for a turnkey car 3.6 x 6.3 = 63.000 rubles !!!
carport for 2 turnkey cars 5.7 x 6.3 = 128.000 rubles !!!

The required welding is carried out during production using shielding gas, which ensures high quality welded joints.

Painting is also carried out at the factory. High-temperature drying of the painted layer ensures high strength and quality of the protective outdoor coating.

The strength of our structures is ensured by correct load calculations (all calculations are in accordance with the current standard).

The terms of production and delivery of ordered structures are within 2 weeks. Installation of the structure takes one to two days.

Canopy no.	the size of the canopy on the roof, w * d	size at extreme racks, w * d	3d sketch with dimensions	covered area	canopy price, including installation and delivery (turnkey)
the width of the canopies is 3.4 m.
3	3,4 * 5,3	3,0 * 5,0		18	61 490
4	3,4 * 6,3	3,0 * 6,0		21,6	69 190
5	3,4 * 7,4	3,0 * 7,1		25,2	77 990
6	3,4 * 8,5	3,0 * 8,2		28,8	82 390
7	3,4 * 9,5	3,0 * 9,0		32,5	92 290
the width of the canopies is 4.4 m.
16	4,4 * 3,2	4,0 * 2,9		14	46 090
17	4,4 * 4,2	4,0 * 3,9		18,5	60 390
18	4,4 * 5,3	4,0 * 5,0		23,2	71 390
19	4,4 * 6,3	4,0 * 6,0		27,7	80 190
20	4,4 * 7,4	4,0 * 7,1		32,4	92 290
21	4,4 * 8,5	4,0 * 8,2		37	104 390
22	4,4 * 9,5	4,0 * 9,0		41,7	115 390
23	4,4 * 10,6	4,0 * 10,0		46,3	120 890

Why people choose polycarbonate

Let's take a look at what this material is. Polycarbonate is a hard polymer plastic. It is widely used not only in construction but also for the production of lenses, CDs, computer parts.

May be:

Cellular polycarbonate is a series of thin plates connected by jumpers. In cross-section, the sheet is divided by cells, and the air in them provides good thermal insulation properties of the material.

Monolithic polycarbonate is a solid sheet of polymer without voids and cells. It is a versatile building material with excellent light transmission and can replace ordinary glass.

Among the advantages of the material, it is worth highlighting:

• Affordable price. Polycarbonate is cheaper than metal, glass and wood.

  

• Lightweight for easy installation. Cellular polycarbonate is 16 times lighter than glass.

  

• Fire safety. It is non-flammable and does not contribute to the spread of fire.

  

• Resistance to temperature extremes. Polycarbonate perfectly tolerates operation in the temperature range from -40 to +120 degrees Celsius.

  

• Reliability and durability. A properly made canopy made of this material will serve you for decades.

  

• Flexibility and ductility. You can create structures of various design forms.

  

• Variety of colors. Polycarbonate is available in all possible colors, which makes it possible to choose a material that fits perfectly into the style of the building.

  

• Simplicity of care. You don't need expensive detergents to clean the canopy cover from dirt. It washes perfectly with ordinary soapy water.

  

Not surprisingly, with so many useful properties, polycarbonate is so popular as a material for building sheds. Let's figure out what can be a canopy to a house?

Visor above the entrance

The canopy above the entrance protects the porch from rain, snow and other adverse factors. It can be attached to the building on suspensions or installed on additional supports. The frame material is wood, steel or aluminum.

Polycarbonate awnings on a forged frame look very nice and interesting. Floral motifs, complex geometric shapes of forged elements make the visor look luxurious and chic. Such designs fit well with the style of old buildings and classic private houses.

The canopy over the entrance made of polycarbonate not only perfectly fulfills its main function, but also serves as a harmonious addition to the exterior, and in some case - a bright accent that can completely change the visual perception of the appearance of the house. Due to the variety of colors, the material can be ideally matched to the color of the building.

Carport

The advantages of building a carport for your home are obvious:

When designing such a structure, the dimensions of your car are taken into account, and such a part of the building is selected that is convenient to drive up to.

Cozy terrace

A common option for installing a polycarbonate canopy to the house is to create a terrace for summer vacations. It can be placed directly in front of the main entrance or from the side of the building. Tables and chairs are installed, the high fire safety of the material allows you to place a barbecue on such a terrace.

And this is another example of how the variety of colors allows you to make the perfect design to your taste. It is very pleasant to be under the completely transparent roof during the warm summer rain. They say that the flowing drops of water can be watched endlessly. The tinted coating will protect from bright sunlight and ultraviolet radiation. An interesting lighting effect is created by bright sheets of colored polycarbonate.

Wood is an environmentally friendly natural material that has a pleasant smell

Where to order a canopy?

There are people who do not trust the masters in anything, believing that it is easier and cheaper to do it yourself. But this option is good only for those who are professionally engaged in construction, clearly know the entire technology of the process, and besides, they can buy materials from friends cheaper than in a hardware store or on the market. What the rest are at risk:

That is why you should trust the professionals! The company Canopy Master has been dealing with awnings, canopies, gazebos and greenhouses for 12 years. In our arsenal there are hundreds of successfully completed projects, the quality of which is confirmed by their service life.

The best craftsmen, who not only know and love their job, but also treat it with maximum responsibility, will make you a custom-made canopy in just 2-4 weeks. You will be pleasantly surprised by the daily help of a competent person who will answer all your questions.

Don't waste your time and energy. By ordering the product today, you will be able to enjoy a great vacation in the near future.

Message
sent.

Plastic pipes are probably one of the best building materials. They are used not only to create piping systems for transporting various media, but also plastic pipes can be used to make furniture, greenhouses, vases, camp chairs, pens for animals, and many other useful things. This article will tell you how to make your own canopy out of plastic pipes.

Preparatory work

The preparatory work includes the choice of a place for a shed. This is a very important stage, since the design of the canopy is chosen from where the canopy will be located and what function will be assigned to it.
Consider the main points that need to be considered when planning the construction of a canopy from plastic pipes:
The purpose for which the canopy will be used. Since the size of the canopy, its appearance and shape, as well as the advisability of installing the foundation and organizing the walls and floor, will depend on the purpose. There are 2 types of canopies: economic - to protect vehicles and property; applied - the organization of a place for children's games and recreation.

Canopy construction. Temporary or permanent. If the canopy is used to protect vehicles, then it must be solid and non-separable, as well as strong enough. If the use of a canopy is necessary to protect from rain or sun in the warm season, then such a structure is made collapsible. For a demountable structure, it must be taken into account that it is quickly assembled and dismantled.
The location of the canopy. When choosing the location of the canopy, it is necessary to take into account a number of factors: sun illumination, visibility. Before installing the canopy, it is necessary to clear the area. For the base of the canopy, clear the ground from debris and level it. The ground that will be under the supports must be softened.
Support structure. Supports for the canopy are made of pipes, and they are selected depending on the load of the roof. Corner and arched roofs are subject to less stress from snow and rain. Also, the load depends on the type of roof - arched, single-slope or dual-slope. The more complex the roof structure, the greater the support requirements.
Roof material. The main thing that you need to pay attention to when choosing a material for a canopy roof is its purpose. For temporary awnings, you should choose a material that is easy to dismantle, as well as the ability to reuse it - for such awnings, a durable oilcloth is suitable, you can use curtains for the bathroom. If the canopy is used to protect the car, then polycarbonate can be used as a material for the roof, this material will perfectly protect against external factors (rain, snow). The use of polycarbonate is undesirable for a gazebo, which will be used for recreation, since this material accumulates the thermal energy of the sun and people under it will be uncomfortable.

You can buy materials for the construction of a canopy at the building materials store hozdvor.com.ua. Here you will find a wide range of high quality building materials for all occasions.

Existing types of awnings

Sheds made of metal-plastic pipes can perform a variety of functions, and their appearance will largely depend on this.
Consider the main functions that the canopy should perform:
protection from the effects of the external environment: people, animals, birds;
protection from the effects of the external environment of tools, cars;
creating a shadow on the playground.

Any canopy made of plastic pipes is a very convenient and reliable design that does not require maintenance and, moreover, is inexpensive. It will not be difficult to build such a canopy on your own.

Canopy assembly procedure

Option for a summer cottage made of PVC pipes

Initially, it is necessary to prepare all the tools and necessary materials. To build a canopy you will need:
two plastic pipes of the same size, the length of which depends on the required height of the canopy;
waterproof fabric;
a strip of durable fabric, in length it should be equal to the length of the pipe multiplied by two;
four steel pipes 0.2 meters long. Steel pipes will be the foundation for plastic pipes, for this reason, their diameter should be slightly larger than the diameter of plastic pipes;
sewing machine and thick nylon threads.
After all the necessary tools and materials have been collected, they begin to erect a canopy. Major works include:
at the first stage, the marking is carried out, taking into account the place for the supports and with the expectation that the waterproof canvas covered the required area. The marks are made opposite each other in four places;
after marking the territory, steel pipes are driven into the marks for the supports. There should be 2 cm in the height of each pipe on the surface, so that a plastic pipe can be inserted into them;

Wooden frame as a support

Next, you should cut off the plastic pipe of the required length, which should be equal to the required height of the canopy multiplied by 2. Also, with the length of the pipes, it is necessary to take into account the distance between the supports;
after that, it is necessary to sew the canvas, its width should be equal to the width between the supports, taking into account the deduction on each side for the loops - 10 cm. The length of the canvas depends on the preferences of the master, but it should overlap the facade plane of the canopy being erected by half;
the canvas of the required size is hemmed along the edges. For this purpose, a dense fabric is used, into which, in turn, the pipe will be inserted. Also, instead of a solid pocket, loops can be made around the pipe, the distance between the loops should be at least 10 cm;
After the awning is assembled, proceed to the unrelated assembly of the awning. For this purpose, the canvas is put on plastic pipes, after which the plastic pipes are inserted into the steel branches from the pipes. After that, it is necessary to correct the awning and make it the required height.

Output

In conclusion, we note that the PVC pipe canopy is a very convenient and practical design that will allow you to hide from the scorching rays of the sun in hot weather, as well as from the rain. It is possible to make canopies from plastic pipes for absolutely any purpose, but for whatever purpose it is made, such a canopy will always be convenient and practical.

Video: PVC pipe canopy and bathroom curtains