Windows with wooden frames are a wonderful choice for those who appreciate classics and care about maintaining a cozy climate in their home. Over time, the tree loses its presentable appearance, so it needs to be restored in time.

With new windows high quality There are no problems - painting them is not a problem. But restoring old wood frames with shabby appearance sometimes causes difficulties. So how do you paint an old wooden window?

Preparation before painting

So, there is an old wooden window, slightly damaged by time. Under no circumstances should you start painting it with raw paint from a can, as many do. This can only be done in one case - if the frame has just been purchased and is of excellent quality. But even here you can’t do without a primer.

An old window needs to be thoroughly prepared before painting, and to do this you need to assess its condition:

• conduct a detailed diagnosis of all aspects window frame;
• assess the tightness of the glass to the glazing beads;
• check the presence and condition of the old paint layer.

It is imperative to prepare the window for painting. If you ignore this point, you can only ruin the product and waste your time. After a thorough diagnosis, the frame should be removed from all defects that were found. If there are rotten places, they need to be scraped off with a sharp metal object, for example, with a knife. Old paint, if it doesn't adhere well or bubbles, also needs to be removed. To upgrade your window with your own hands, it is better to completely clean the frame of old paint using a special solvent and a knife.

After removing damaged areas of wood, irregularities and pits often appear on the window frame. Coarse grinding will help correct the problem. sandpaper followed by applying putty. At the same time, in this way you can fill the cracks that appear as a result of the wood drying out. Preparing the window for painting does not end there. Once the putty layer has dried, it can be polished with fine sandpaper. All that remains is to cover the frame with a layer of primer enamel. You can’t do without it, since paint applied directly to wood does not adhere well, swells and peels off ahead of time.

If preparatory work completed and the window frame is level smooth surface, you can move on to painting the old wooden window.

Applying paint to the frame

To make applying the paint easier, it should be diluted with a solvent. The choice of liquid for dilution depends on the composition protective coating. This can easily be clarified with the seller from whom the paint was purchased. But if you can’t get any recommendations on this matter, you can use the universal thinner “White Spirit”. It is suitable for almost all types of alkyd paints. How to calculate the optimal amount of solvent? Here everything is chosen by eye. The main thing is that ready mix It did not have a thick or watery consistency.

To paint the frame without staining the glass, you need to use masking tape. It will help refresh the window without losing its transparency. The adhesive tape is glued around the perimeter of the glass close to the glazing beads. When working with a brush, minimal splashes are created, so narrow strips of masking adhesive tape will be enough. To paint a window frame easily, quickly and efficiently, you should adhere to several rules:

• During work, you must be careful, make sure that the paint goes on evenly and does not get into unnecessary places;
• It is not recommended to immerse the entire brush in a container with dye. It is enough to dip the brush halfway and walk it along the edge of the can to get rid of excess paint;
• Coloring must be done from top to bottom. This will prevent the appearance of sagging and leaks;
• there is no need to try to apply as thick a layer of paint as possible in one go. This can lead to uneven surfaces.

One simple rule will help you paint wooden windows correctly: it is better to apply 2-3 layers, the first of which should be thin. Moreover, the next round of painting is carried out only after the previous layer has completely dried. Thus, the entire process can take several days, depending on the drying speed of the coating. This technology helps to get rid of unpainted areas and provides reliable protection of the wooden frame from natural precipitation and sunlight.

Painting a wooden window is not difficult. Armed with patience and tools, an old piece with an unsightly appearance can be turned into a beautiful thing, as proven by the example of a window frame. With the above tips, you won't have to rack your brains thinking about how to paint. wooden windows By old paint. The main thing to remember is: “It’s not so hard to achieve professional quality painting old windows, how long to preserve this quality for a long time.”

https://www.youtube.com/watch?v=Cnner994xzI Video can't be loaded: Tips for painting old wooden windows (https://www.youtube.com/watch?v=Cnner994xzI)

The short period has passed when installing plastic double glazed windows was considered fashionable and stylish, and the tree is gradually regaining its lost popularity. Many owners wooden frames They have already changed their minds about replacing the still strong wooden window frames with practical plastic and are deciding how to restore them with their own hands and what paint for the windows is best.

Requirements for dyes

To obtain high-quality, durable painting of window frames, it is necessary to take into account all operating conditions. Enamel for windows and doors (if there are additionally wooden doors, it is recommended to paint them at the same time as the frames) must meet the following parameters:

1. Location. For wooden doors and frames located on the street side, the dye must have increased moisture resistance and the ability to withstand temperature changes. If you plan to paint windows in the bathroom or kitchen, then you need to pay attention not only to the moisture-repellent properties of the product, but also to its abrasion resistance, because wooden frames in these rooms have to be washed frequently.
2. Availability of additional “bonuses”. For example, fire retardant or antiseptic additives that will protect the wood from fungus or fire.
3. Environmentally friendly. The selected material should not have a toxic effect on the human body.
4. No smell. For outdoor use odor of great importance no, but the smell should not persist indoors for a long time. Long-lasting odor associated with repairs chemicals disrupts the cozy atmosphere of the home.
5. Drying speed. This parameter is very important when making window frames with your own hands from the street side. For outdoor work, it is recommended to use quick-drying compounds.
6. Easy to apply with your own hands. Many novice craftsmen, when painting window frames and frames with their own hands, encounter difficulties when applying the dye (drips, uneven coloring), and the quality of the work does not meet decorative requirements. In order for DIY painting to be of high quality and aesthetically pleasing, it is necessary to take into account the fluidity and hiding power of the enamel.

By selecting enamel for windows and doors taking into account these parameters, you can ensure high-quality and durable window repairs with your own hands.

Choosing a coloring agent

For wooden structures in residential premises, the following types of paints will be optimal.

Acrylic

Acrylic - on latex or water based– quick-drying, after drying they form a smooth, beautiful film. They are easy to work with and are recommended for use by beginning craftsmen who decide to paint wooden frames with their own hands.

Due to the fact that water or latex is used as a solvent, there is only a slight odor when working with the coloring agent, and after 1-2 hours after drying, the odor completely disappears. Acrylic water-dispersion paints can be used to paint inside and outside. If acrylic-latex ones are used, then they should be indicated “for external or internal use” (latex polymer without additional additives is weakly resistant to temperature changes).

Alkyd

Made on the basis of organic resins and oils, they have high ability penetrate the wood structure. After drying, alkyd dyes form a durable film that is resistant to atmospheric phenomena, abrasion and exposure to chemicals. Disadvantage: alkyd substances have organic basis persistent, long-lasting odor.

Products based on aqueous solvents are less durable. But after drying they have almost no odor and are suitable for painting wooden surfaces in rooms. These solutions take quite a long time to dry, and when used outdoors, a day of warm, clear weather is required.

Oily

This composition is based on oil solvents Due to its ductility, it weakly penetrates the wood structure, but forms a durable moisture-repellent layer on the surface. It takes a long time to dry and after drying for a long time has a specific smell. Oil dyes are not used very often for coloring.

Which enamel to choose? Each master decides this for himself, based on the characteristics decorative design and your skills.

Color solution

It’s not enough to choose a composition with suitable chemical properties. Wooden frames must not only be protected from external influences, but also processed in accordance with the interior.

The paint and varnish industry offers consumers a large color scheme the above coloring agents. The windows can be painted either purple or red, but how will this fit into the main design?

Interior decorators for interior decoration recommended to use:

• traditional shades of white;
• coloring “like light wood”;
• beige, light yellow and other sunny tones, if this suits the interior design.

Of course, the window base can be painted any color you wish, but it is worth remembering that too bright or too dark colors bring dissonance to the design of the room.

Painting outdoors is not so demanding color tones: frames can be of any color, the main thing is that they are in harmony with the facade.

What you need for painting

Before you start restoring wooden frames with your own hands, you need to prepare necessary tool And consumables. Supplies you will need:

• wood putty to level the base;
• wood sealant for filling cracks;
• protective impregnations (if the paint does not contain additional protective additives);
• degreasing solvent;
• masking tape.

In addition to consumables, the following tools will be needed:

• scrapers for removing old coating;
• plane and other tools for leveling the base;
• spatula;
• screwdrivers and hammer;
• a set of “skins”;
• brushes

Preparing the base

To make wooden frames look beautiful, it is not enough to simply clean and paint them. Failure to comply with all preparatory stages may lead to the following:

1. The consumption of paints and varnishes will increase.
2. After the painted surface has dried, all the unevenness of the wood will become visible.
3. The decorative coating will have weak adhesion to the base and will soon begin to crack and peel.

If you want to have it for a long time beautiful windows and do not repaint them every year, then before you paint it yourself, you need to carry out the following preparation:

1. Remove any remaining old paint using scrapers.
2. Remove window handles and latches.
3. Clean the surface with sandpaper to a smooth base.
4. Carefully inspect the frame base. Fill dents and other defects with putty, remove uneven surfaces with a plane. If large cracks appear on the windows during operation, they must be sealed with sealant.
5. After leveling, smooth the surface again with sandpaper, wash and dry well.
6. Cover the glass with masking tape to prevent primer and enamel from getting on them.
7. Treat the wood with a degreasing solvent. This is necessary to remove invisible fatty traces from the base that reduce adhesion. From safe degreasers when self-repair It is recommended to use alcohol-containing compounds, for example, such a solution as cheap and accessible to all craftsmen as white spirit. Alcohol-containing products dry quickly and do not leave an unpleasant odor.
8. Apply protective impregnation. This step is necessary if the selected enamel or primer mixture does not contain wood-protecting additives. All wood fibers are treated with impregnation using a brush and left until completely dry.
9. After the impregnation has dried, the selected primer is applied. The primer should be applied by carefully painting all areas of the surface, moving along the wood fibers. Adhesion depends on priming decorative covering with the base and consumption of paints and varnishes. Don't skimp on primer: experienced craftsmen For durability of the repair, it is recommended to apply it in 2-3 layers - each subsequent layer after the previous one has dried.

After the last layer of primer has dried, you can begin painting.

Features of painting work

Painting wooden frames is a little different from traditional ones painting work on wood. To receive excellent result Painting should be done as follows:

1. Apply a strip 3-5 mm wide to the surface near the glass with a thin brush. This will prevent paint from splashing when the brush touches the glass and will allow you to thoroughly paint the wood-glass joint.
2. Carefully paint the glazing beads near the glass.
3. Paint the opening part of the sash and where it attaches to the window frame.
4. Paint all horizontal parts.
5. Apply paint to vertical parts.

After this, the window frame is painted and, lastly, the window sill. After the first layer has dried, the second decorative layer is applied in the same order.

For DIY window restoration to be successful, experts recommend the following:

1. Apply the dye along the wood fibers.
2. For the first layer, make the enamel more liquid.
3. If drips occur, remove them immediately with a cloth soaked in solvent.
4. Remove masking tape immediately after painting is completed. If this is not done and the enamel dries, then removing the adhesive tape can damage the decorative coating.

By selecting the necessary paint composition and following the suggested recommendations, even a novice master will be able to carry out high-quality restoration work.

Windows are the “eyes” of a house. Nowadays, most buildings seem to be impersonal due to the fact that standard PVC double-glazed windows are used everywhere. However, there are those who, despite fashion and practicality modern technologies, still gives preference wooden structure, because its environmental and aesthetic advantages are undeniable.

In order for wooden frames to last longer, it is necessary to reliably protect them from the influence of sunlight and dampness, as well as various insects and their larvae. Painting a wooden window is designed to accomplish all these tasks. In addition, such processing will preserve the appearance for a long time, however, provided that it was carried out correctly and in a timely manner. We will tell you how to paint and protect new wooden windows, as well as restore old ones if possible.

What tools are needed?

The simplest set is required when painting a new window. For old design the list is expanding noticeably. As for the tools, prepare in advance a spatula, scraper, drill with a special attachment or grinder, roller and brushes, sandpaper (fine and coarse), metal sieve, paint container, stable chair, stool or stepladder, rags, and newspapers.

Next on the list are consumables. Strictly speaking, this is what to paint wooden windows and treat them before: putty, primer, paint, solvent, white spirit. Do not neglect protective equipment such as a mask, goggles, respirator, hat and gloves.

What paint to choose for windows?

Even a professional will not be able to definitively answer the question of which paint to choose for painting windows. The preferences of each owner of a wooden structure are different. Someone for traditions and white, others - for the naturalness and natural structure of wood. Modern construction market offers a very wide choice:

• alkyd enamel;
• acrylic (water-dispersed) paint;
• clear varnish;
• oil paint;
• primers and drying oil;
• solvent-based stain.

If preference is given natural color wood, then experts recommend using special varnishes, glazes and impregnations for coloring and protection. They perfectly penetrate the wood, form a water-repellent layer and prevent the penetration of rot and mold, and also protect against pests.

For interior work, it is preferable to use acrylic paint, which is practically odorless and dries quickly (literally in a couple of hours). It is best to treat the structure from the outside. But the question of what paint is best to paint wooden windows, imported or domestic, is a purely personal matter for each owner, his preferences and financial capabilities.

Step 1: removing old paint from the window frame

If they are made of new wood, then painting them is not particularly difficult. The situation is much more serious with old windows, which have already been painted several times. Before carrying out a new treatment, they should be carefully prepared. It is best to remove peeling paint completely. Moreover, the better this is done, the more attractive the end result will be.

Old paint from windows can be removed using special compounds that soften the layers, gradually turning them into a curdled mass that can be easily removed with a scraper or spatula. However, it should be remembered that such products are quite toxic, and therefore when working with it you should use gloves, goggles and a respirator.

When treating old windows, you can use a construction hair dryer, which will soften the old paint using hot air. Then it will be easy to remove it with a scraper. Remove the old coating in stages, warming only small areas. Before the procedure, it is advisable to remove the glass from the frames.

If the coating has not worn out much under the influence of atmospheric factors, you can get by with small preparatory activities and don't remove it completely. However, before painting wooden windows using the old paint, in any case they should be thoroughly sanded and then cleaned of dust, and uneven areas should be treated with putty.

Step 2: Seal Gaps and Cracks

Wooden products have one significant drawback - cracking when drying. It is quite common to find both small and quite deep cracks on window frames. Therefore, before painting, be sure to inspect the structure, including the joints of the window unit and the wall. Cracks are places where dirt and moisture accumulate. Thoroughly clean them of accumulated dust using a brush or vacuum cleaner, dry them and fill them with a special putty. Once the compound has dried, sand the entire wood surface using coarse sandpaper. Otherwise, after painting, uneven areas on the frame will be very noticeable.

Step 3: Coating the window frame with primer

Before you paint a wooden window frame, you need to prime it. This is done not only in the case of new design, but also when stripping the old one down to the wood itself. If this is not done, the paint will not adhere well and within a year you will have to put it in order again. Applying a primer promotes better adhesion of paint to the surface and reduces its consumption. After using it, the wood fibers may rise slightly, so experts advise sanding the window frame again using fine-grained sandpaper. This should always be done in the direction of fiber growth.

The choice of primer depends directly on what kind of paint will be used in the future.

Step 4: Final preparation before painting

The process of preparing wooden windows for painting ends with an inspection of the structure. You should carefully inspect it for traces of resin. This is especially true if the frame is new and/or made from coniferous species tree. Resinous secretions should be carefully removed, since the acid present in them will gradually destroy the paint layer. Next, the surface of the wood needs to be degreased. What composition should be used for these purposes depends on whether it should be compatible with it. So, since ancient times, complete with oil paint turpentine was used. Its residues on the surface did not in any way affect the quality of painting. White spirit or simple kerosene and gasoline are popular.

Step 5: Protect the glass surface of the window

As practice shows, even the most experienced craftsmen easily touch structures with a brush. Therefore, it will be better if you protect it with special masking tape. The process will not take much time, but painting a wooden window will be much faster, and the coating will be streak-free, smooth and neat.

Keep in mind that glass should be removed from the surface before the paint on the window frame dries. Otherwise, there is a risk of tearing off part of the paintwork along with it.

Step 6: Paint and Brushes

Whatever composition you choose to paint a wooden window, you should first mix it well right in the jar. Then the paint must be filtered through a metal sieve into a special tray or other container. This step will save you from lumps that may later fall on the surface to be painted.

Do not dip the brush completely into the paint; it is best to do it halfway. The excess should remain in the tray or jar. To do this, carefully move the brush along the edge of the container. Large quantity There is absolutely no need for paint, as you will only contribute to the formation of smudges.

Prepare several types of brushes in advance. For the most hard to reach places Smaller ones are suitable, for a flat surface - large ones or a roller. A flat brush is much preferable to a round one.

Step 7: Applying Paint to the Surface

So, having learned how to prepare the surface before painting wooden windows outside and inside and having completed this stage, you can safely begin the main work.

It is best to paint a window from the inside out. The frame should be opened and initially processed internal surfaces, primarily horizontal. Next, move from bottom to top. If there are shaped elements on the frame, it is better to start with them using a narrow brush. For smooth surfaces use a roller, because with its help the paint goes on much more evenly. Apply it in several layers (2-3). Do not try to cover all dents, gaps and cracks with one stroke. A thick layer of paint will certainly begin to spread, sagging will appear and, in general, the work may be ruined.

Apply a thin first coat and let it dry. The waiting time depends on the weather and air humidity. When the surface is ready, apply a second coat of paint. As a rule, this is enough. In the case of old windows, a third layer may be necessary, since dry wood absorbs paint strongly.

What weather is best to paint windows?

The question of what weather is best to paint windows is far from idle, as it might seem at first glance. Experts always pay attention to this aspect. They advise carrying out work on a cloudy spring day, when it is already warm, but there is still little moisture in the air, and ultraviolet radiation does not have a destructive effect on the paint. Window frames dry best at temperatures above +5°C and humidity no more than 80%. Avoid rainy weather. Drops of water on the surface on which the paint is applied lead to further “bubbling” of the coating. It not only spoils the aesthetic appearance, but also contributes to rapid destruction. In addition, when painting a wooden window, the coating may peel off due to dampness, poor primer, or poor-quality preliminary cleaning of the surface.

It is no secret that wooden windows are still the most preferred for installation in residential premises, and above all, due to their environmental friendliness. They do not interfere with natural air exchange in the house and do not release any toxic substances into the air. Wooden window designs They are also distinguished by their respectable appearance. But despite all its obvious advantages, caring for wooden windows is quite complex and labor-intensive. In particular, to protect wood from negative impact environment it must be painted, and depending on what paint is chosen for wooden windows, the degree of protection, the durability of the coating, and the appearance of the window will depend.

Preparing the surface for painting is an important and mandatory step.

Before deciding which paint is best to paint wooden windows, you need to prepare the surface appropriately. If this is not done, in just a couple of months even the most expensive and high-quality enamel will begin to peel off.

First of all, careful visual inspection frame surfaces There should be no various roughnesses, potholes or cracks, or areas with signs of rot and mold. If such defects are found, they must be eliminated. To do this, you should “arm yourself” with sandpaper (coarse and fine), a jar of ready-made wood putty, as well as a special antifungal compound (or a primer containing such additives).

All irregularities/roughness must be carefully processed using sandpaper. Cracks, chips and potholes must be repaired using a special putty. It is applied in a fairly thin layer using a spatula, and after drying it is sanded with fine-grained sandpaper so that the putty area is completely level with the rest of the surface of the frame. All places where there are traces of mold/rot must be thoroughly dried (you can speed up the process with a hair dryer) and treated protective composition. If desired, you can apply to this place thin layer putties.

Advice ! Before filling, it is advisable to treat the wood with any acrylic primer- this will improve its adhesion to wooden surface and dust it off after sanding. Before painting, it makes sense to check all window fittings.

Choosing paint - the main thing is not to make a mistake with the composition

There is no clear answer to the question of what paint to paint wooden windows, since each owner of a wooden window has his own preferences. Some prefer to preserve the natural color and texture of wood, for others the only acceptable option are window slaves of white color.

If a decision is made to preserve the natural color of natural wood, special impregnations, varnishes or glazes must be used to color it and impart protective properties. These penetrate wood well, give it water-repellent properties, prevent the formation of mold and rot, and also protect the wood from insect pests. Along with quite expensive imported compounds, there are also more affordable domestic analogues on the market, which are not inferior in quality and protective characteristics to “foreign” ones (for example, Neomid Biocolor Ultra).

IN modern conditions the question of which paint to choose for painting wooden windows is very relevant, since the choice paint and varnish material big enough:

• acrylic paint(water-dispersed);
• alkyd enamel;
• oil paint;
• clear varnish;
• drying oil or primer;
• solvent-based stain.

And if the answer to the question of which paint is best to paint wooden windows on the outside can definitely be alkyd enamel, then for interior work acrylic paint is more preferable, which is practically odorless and dries in a few hours.

How to paint wooden windows using old paint

If the wooden frames are new, their painting is simple. The situation is much more complicated if the window has already been painted. Before painting wooden windows with peeling paint, it must be removed, and the better this procedure is performed, the more attractive the painted window will look. To remove old paint there are special compounds, which soften it, turning it into a cheesy substance that can be easily removed with a scraper or spatula.

Attention ! Compositions for removing enamel are quite toxic, and when working with them it is necessary to use protective equipment and avoid inhaling the vapors of the product or getting it on the skin.

If the house has construction hair dryer, you can do without chemicals, softening the paint with hot air and removing it with a scraper. It is worth warming up the paint in small areas, since it cools quite quickly. Before removing old paint from wooden windows using a hairdryer, it is advisable to remove the glass from the frame. After you have managed to remove the paint from the wooden windows, they need to be sanded and primed. After the primer has dried, you can proceed directly to painting.

After you have determined exactly what paint to paint wooden windows with, you should prepare the appropriate tool:

• brushes of different widths;
• short pile roller;
• masking tape;
• when using alkyd enamels you will need a suitable solvent;
• clean rags.

Masking tape will be required if there is no desire or opportunity to remove the glass - in this case, before starting painting, you should stick the tape at the junction of the frame and the glass. It is most convenient to start painting a window with “curly” surfaces, for which it is most convenient to use narrow brush. You should not put too much paint on it, which will avoid the formation of smudges.

It is better to paint smooth surfaces with a roller; in this case, the paint will lie much more evenly than when applied with a brush. In addition, regardless of what paint wooden windows are painted, it is better to start the process from the outside. This is due to the fact that the layer of paint and varnish material is usually moisture-proof, and if you start painting from inside, moisture from the wood simply does not have time to escape (relevant when painting in spring and autumn).

As practice shows, if white paint is chosen for wooden windows, its service life will be much longer than that of colored paint, since white enamel, by reflecting the main part sun rays, heats up several times less than tinted paints. Even if the old paintwork on a wooden window is firmly in place, has no signs of peeling or cracking, and you just need to refresh the color, the surface still needs a little preparation.

It is advisable to sand the entire surface with fine-grained sandpaper, then thoroughly wash the frame with soapy water. To be sure, you can wipe it with a rag soaked in solvent, gasoline or kerosene. After this, you can begin applying a new coat of paint.

Before painting windows yourself, you can read this “video instruction”

Windows with wooden frames are a wonderful choice for those who appreciate classics and care about maintaining a cozy climate in their home. Over time, the tree loses its presentable appearance, so it needs to be restored in time.

There are no problems with new high-quality windows - painting them is not a problem. But restoring old wood frames with a shabby appearance can sometimes be difficult. So how do you paint an old wooden window?

Preparation before painting

So, there is an old wooden window, slightly damaged by time. Under no circumstances should you start painting it with raw paint from a can, as many do. This can only be done in one case - if the frame has just been purchased and is of excellent quality. But even here you can’t do without a primer.

An old window needs to be thoroughly prepared before painting, and to do this you need to assess its condition:

• carry out detailed diagnostics of all sides of the window frame;
• assess the tightness of the glass to the glazing beads;
• check the presence and condition of the old paint layer.

It is imperative to prepare the window for painting. If you ignore this point, you can only ruin the product and waste your time. After a thorough diagnosis, the frame should be removed from all defects that were found. If there are rotten places, they need to be scraped off with a sharp metal object, for example, a knife. Old paint, if it doesn't adhere well or bubbles, also needs to be removed. To upgrade your window with your own hands, it is better to completely clean the frame of old paint using a special solvent and a knife.

After removing damaged areas of wood, irregularities and pits often appear on the window frame. Sanding with coarse sandpaper followed by applying putty will help correct the problem. At the same time, in this way you can fill the cracks that appear as a result of the wood drying out. Preparing the window for painting does not end there. Once the putty layer has dried, it can be polished with fine sandpaper. All that remains is to cover the frame with a layer of primer enamel. You can’t do without it, since paint applied directly to wood does not adhere well, swells and peels off ahead of time.

If the preparatory work is completed and the window frame has a flat, smooth surface, you can proceed to painting the old wooden window.

Applying paint to the frame

To make applying the paint easier, it should be diluted with a solvent. The choice of dilution liquid depends on the composition of the protective coating. This can easily be clarified with the seller from whom the paint was purchased. But if you can’t get any recommendations on this matter, you can use the universal thinner “White Spirit”. It is suitable for almost all types of alkyd paints. How to calculate the optimal amount of solvent? Here everything is chosen by eye. The main thing is that the finished mixture does not have a thick or watery consistency.

To paint the frame without staining the glass, you need to use masking tape. It will help refresh the window without losing its transparency. The adhesive tape is glued around the perimeter of the glass close to the glazing beads. When working with a brush, minimal splashes are created, so narrow strips of masking adhesive tape will be enough. To paint a window frame easily, quickly and efficiently, you should adhere to several rules:

• During work, you must be careful, make sure that the paint goes on evenly and does not get into unnecessary places;
• It is not recommended to immerse the entire brush in a container with dye. It is enough to dip the brush halfway and walk it along the edge of the can to get rid of excess paint;
• Coloring must be done from top to bottom. This will prevent the appearance of sagging and leaks;
• there is no need to try to apply as thick a layer of paint as possible in one go. This can lead to uneven surfaces.

One simple rule will help you paint wooden windows correctly: it is better to apply 2-3 layers, the first of which should be thin. Moreover, the next round of painting is carried out only after the previous layer has completely dried. Thus, the entire process can take several days, depending on the drying speed of the coating. This technology helps to get rid of unpainted areas and provides reliable protection of the wooden frame from natural precipitation and sunlight.

Painting a wooden window is not difficult. Armed with patience and tools, an old piece with an unsightly appearance can be turned into a beautiful thing, as proven by the example of a window frame. With the above tips, you won’t have to rack your brains, thinking about how to paint wooden windows using old paint. The main thing to remember is: “It’s not so much difficult to achieve professional quality painting of old windows, but to maintain this quality for a long time.”

https://www.youtube.com/watch?v=Cnner994xzI Video can't be loaded: Tips for painting old wooden windows (https://www.youtube.com/watch?v=Cnner994xzI)