A garage is not only a place for a car, but also a source of invaluable additional space, which can be used truly rationally if you design useful devices with your own hands.

DIY garage accessories

Since the garage, by its intended purpose, is a home for cars, you should be careful to ensure that the space for tools is well organized. Also in the room there will probably be several square meters in order to remove some of the items from the apartment so as not to clutter the living space.

During installation various devices indoors, it is important to consider that all available equipment is at hand. To do this, you can use the following recommendations:

Rational organization of space in the garage creates many tangible advantages:

• it becomes possible to independently carry out short-term repairs of car parts and other mechanisms, due to which you can significantly save money;
• Convenient placement of tools significantly speeds up work and saves time;
• Creation additional places for storing tools, old things, clothes, it makes it possible to unload the apartment from things that are rarely used in the household;
• finally, the well-thought-out internal logistics of the premises allow it to maintain its attractive appearance and avoid clutter.

PLEASE NOTE. At the project development stage, it is important to proceed from the area of ​​the room, and also to take into account several mandatory utility compartments - for storing summer and winter tires, cans, jacks, etc.

Video TOP best ideas for decorating a garage with your own hands

Garage rack: step-by-step manufacturing instructions

Since the garage always contains quite a lot of items, organizing their arrangement is a fundamental requirement for proper storage. The simplest and at the same time convenient option- this is the creation of a rack with shelves.

Preparatory stage

Before you begin installing the structure, you should consider several important requirements:

• The total weight of the rack should not be more than 4-5 centners - otherwise the structure will be very difficult to move if necessary. It will also put significant pressure on the floor, which can deteriorate the quality of the coating.
• When choosing materials, it is important to proceed from considerations of strength and durability of the structure. Metal is optimal, as well as wooden products from beech or oak. Plastic shelves are not suitable - they are not durable and, moreover, may not withstand temperature changes.
• When choosing between a metal and wooden structure, you should proceed from your specific needs. Metal is more durable and stronger, but wood is more affordable. If you need to place a few tools, just make a small wooden rack.
• Since all the tools are very heavy, you should immediately calculate the strength of the structure so that it can withstand at least 100-150 kg on one shelf.

Installation of a wooden structure

To make such a device for a garage with your own hands, you will need ordinary working tools:

• hacksaw for wood and metal;
• hammer, nails;
• screwdriver, self-tapping screws;
• construction tape;
• construction level;
• electric drill.

Before assembly, it is important to prime and varnish all wooden parts. There may be increased humidity or temperature changes in the garage, so the wood will not last long without treatment.

Video - Do-it-yourself wooden shelving technology

Installation of a metal structure

Metal structures are exceptionally durable and strong. In addition, they do not need to be treated with special materials to prevent rotting.

You can make both a rack and separate structures, for example, for storing rubber, from metal.

In this case, you should take into account the rules for storing tires, which are shown schematically in the figure.

At the design stage of a metal rack, you should take into account that it can freely accommodate all the necessary items. You can take this drawing as a basis.

Or this option.

The easiest option is to purchase a modular design and assemble it yourself. But you can make this device for the garage with your own hands. The sequence of actions is as follows:

It is better to place the heaviest equipment on the lower shelves for optimal load distribution throughout the rack. At the same time, the most best option– when the lower floors are made of corrugated metal, and for the upper floors it is quite acceptable to use durable chipboard.

Hanging shelves: fast and practical

Not in all cases there is a need to create a rack, since it will take up a lot of space. On the other hand, in a garage of any size there is always unused upper space, which can easily be used for hanging shelves.

Structurally, it is quite possible to make any version of such a device for the garage with your own hands:

The tools you will need are the standard set described above. The sequence of actions is as follows:

If the shelf is mounted to the ceiling, you can strengthen its connection to the wall using metal corners– then the product will not wobble and will last much longer.

The entire technology is shown schematically in the figure.

Making a shield shelf

The DIY technology for making such a device for a garage has its own differences compared to installing conventional shelves:

• The shield itself is made of durable plywood, the parameters of which are selected according to the situation. Visually, the shield should completely cover the surface of the desktop.
• Space is allocated on the board for all shelves and appropriate notes are made.
• Next, all the holes into which the dowels fit are made in the surface of the structure. It is on them that the hooks will be attached, on which all the tools will be placed.
• The shield is secured to the wall using brackets. The corresponding holes are made using a hammer drill.

All steps are shown schematically in the figure.

DIY tool panel above workbench in garage

Workbench for the garage: step-by-step instructions

Another structure that will probably be needed for repair, plumbing and other types of work is a workbench. It can be purchased in a store, but if you have a certain skill, then it is quite possible to make such a device with your own hands and put it in the garage.

Before carrying out the actual installation work It is important to clarify several important details:

• Where will the table be located?
• What kind of work will mainly be carried out on it.
• What work surface material is suitable - metal or wood?

All these questions are closely related to the purpose of the product. If work is expected to be done frequently, then it is better to choose durable metal. And for standard household tasks, durable wood will do.

It is important to understand that a workbench is not just a work surface. Often it combines the function of a wardrobe, a small chest of drawers and even a metal safe - this set of parameters depends on the specific configuration of the product.

Types of workbenches

The key classification of workbenches is based on the types of work that are supposed to be carried out on it:

At the same time, these functions can be combined, so such a classification is largely arbitrary. The best option such a garage device is a design based on metal frame With wooden surface table and drawers. It is more reliable than its wooden counterpart, and allows you to save on manufacturing due to the fact that some parts will be made of wood. The surface of the table can be reinforced with a metal sheet - then the workbench will last for a very long time.

Technology for making a workbench from a metal frame

To install the structure you will need a standard set of tools and materials:

• welding machine;
• grinder for metal;
• building level;
• jigsaw for wood;
• screwdriver, drill;
• self-tapping screws, anchor bolts;
• hammer and nails;
• metal corners with parameters 5*5 cm;
• square pipes 6*4 cm, total length about 24-25 m;
• steel strip 4 cm thick, up to 8-9 m long;
• paint for wood and metal processing.

These parameters are intended for the manufacture finished product with table parameters 220*75 cm, as shown in the figure.

The sequence of actions is as follows:

Even at the stage of designing a workbench, it is important to decide whether the device will be collapsible or whether it will be permanently installed in the garage. In the case of a collapsible version, all parts are attached using self-tapping screws, and the principles of the technology will be different.

Wooden workbench manufacturing technology

A wooden workbench is less durable than a metal one. It is well suited for cases where the work is supposed to be done less often - several times a year.

To make this device for the garage with your own hands, you can use the same drawing given above, or take the diagram shown in the figure as a sample.

The algorithm will be something like this:

Do-it-yourself garage tipper: step-by-step video instructions

Along with creating the considered devices for the garage, you can also take care to make with your own hands the working tools that will be needed directly for maintenance auto.

One of the most useful installations– a tipper for inspecting the bottom of the car. The need for such a product is most relevant for Russian realities, since not in every case there is real opportunity construction of an inspection pit.

Detailed video instructions with step by step diagram manufacturing

Before making such an installation, it is extremely important to consider the issue of safety. Even a light car can cause an accident if it falls and, at a minimum, will receive serious damage. Therefore, you can only undertake the creation of such a design if you have sufficient skill.

Making your own garage fixtures allows you to rationally organize interior space and essentially get your own workshop in which you can carry out any ongoing repair work.

Original ideas for organizing space in the garage

And finally, a photo selection of visual ideas for creating spacious structures from a variety of items that are likely to be found in any garage.

Since time immemorial, a car storage room has been considered not only a place to relax after a hard day, but also a unique workshop. The men equipped it, creating various homemade products for the garage with their own hands. In a small space you need to arrange a huge number of things for convenient use and reliable storage. Enterprising craftsmen do not lag behind their ancestors, but continue what they started, using modern methods and technology. Consider popular ideas original designs for the work area of ​​real men.

When setting up a room for parking a car, you must follow the basic safety rule. The entrance gate or door should be easy to open and access to it should always be free.

Homemade products for the garage - a wise approach to modernizing space

Almost every car enthusiast can build a “house” for an iron horse with his own hands. The main thing is to tune in to the fact that this is a constant and long-term process. It doesn't hurt to use creativity, skill, and strong determination to achieve your goal. Practical advice experts will help you create original homemade products for the garage, for those who are ready to get down to business. In addition, it brings enormous satisfaction when ordinary objects are transformed into a necessary and valuable thing.

Car tire storage

Experienced drivers change the “shoes” of their car every season. Where is the best place to store tires so that they do not lose their properties? A simple do-it-yourself garage project will solve this painful issue forever.

For proper storage tire design, the key role is played by the type of wheel design: with or without a disc.

Car tires mounted on rims are stored hanging or in stacks. For the first option, simple materials are used:

• metal cables;
• chains;
• luggage straps

They are often fixed to the ceiling, load-bearing wall or to the beam, which is located in the upper part of the room. An original craft for a garage with your own hands is driving metal hooks or pins into the wall. They are stuffed over the entire area of ​​the wall, the main thing is that the wheels do not touch each other.

Metal pins should not protrude beyond the edges of suspended structures.

Car tires that do not have rims are stored standing up. Suitable shelves are made for them by welding profiled pipes with a diameter of 30 mm or a corner. The width of the structure is 4 times the width of the wheel plus 15 cm for free placement on a shelf. The height of the rear part of the structure is 10 cm higher than the outer volume of the tire. This DIY garage fixture is hung on the wall.

The tire storage area must be protected from sunlight so that the rubber does not lose its properties.

The good owner has everything at hand

To set up a work area in the garage, experienced drivers first determine in which part to place it. If the room has rectangular shape, then it is convenient to build a “creativity corner” along the entire width of the back wall.

This useful device DIY made for the garage will help solve three main problems:

• compact layout large quantity things;
• ease of use;
• free movement indoors.

For a wide garage, it is better to place the structure along one of the side walls or as corner option. In this matter, the garage owner makes his own decision based on the size of the room.

A great idea for the garage is to make your own wooden table or workbench. For the design you will need:

• profiled pipe or metal corner;
• boards;
• moisture-resistant plywood or chipboard;
• fasteners;
• set of tools.

Using welding equipment, the frame of the future table is made, which is sheathed with plywood or chipboard. Alternatively, the structure can be made entirely of wood. To compactly fill the space, shelves are installed under the tabletop, where plastic or wooden containers are placed.

In addition, craftsmen use various tricks in the garage - they build a rack from plastic canisters with their own hands. Identical containers with the handle at the top will do. One of the sides is cut out, turning the canister into original box for the car enthusiast's valuables. Then the containers are placed on a wooden or metal rack, as shown in the photo. Such garage storage systems serve car enthusiasts for many years. Because plastic is not afraid of dampness, temperature changes and is resistant to mechanical damage. As a result, the wise master has all the details at hand, which means he works without distractions.

Folding table for small spaces

A simple design that can be made from an old cabinet will help you set up a work area in a small garage. For the design you will need:

• chipboard sheets;
• corners;
• several loops;
• mortise nuts for furniture;
• wooden block;
• self-tapping screws;
• anchor bolts.

First, mark the future structure using a level. On wooden block drill through holes and attach to the wall using anchor bolts. Then the prepared table surface is connected to it using moving curtains. The design fits perfectly into small room and is used only when necessary.

Ideal place for tools

Every driver has a whole arsenal of tools at his disposal. Some of them are used quite often, others - once a year. Original homemade devices for the garage are simple solution question. They contribute to perfect order in the room and also decorate its interior.

Organized people who keep everything in its place can benefit from locked drawers for tools and car parts.

One of the devices is performed in a simple way. A metal reinforcing mesh (cage size 10 cm), which is made of wire (diameter 2 mm), is attached to the wall. Some parts of the cage are bitten off, then folded back and made into hooks or crossbars.

Motorists hang on them:

• hand saw for metal;
• watering can for fuel;
• various rubber hoses;
• small car spare parts.

Another way to organize valuable tools for car enthusiasts is a shelf for screwdrivers. To do this, the board (about 15 cm thick) is thoroughly sanded, bringing the surface to a smooth state. Next, drill holes of different sizes (one or two rows). Each of them is cleaned to prevent the appearance of splinters. Attach the structure to the wall using brackets, after which screwdrivers or chisels are inserted into the holes. For storage hand tools make a similar device. TO vertical surface nail the board. One of its sides is pre-sawed off so that it is convenient to hang pliers and wire cutters different types and pliers.

To place battery equipment in the garage, a special shelf is built. Its upper part has flat base. At the bottom, protrusions of different formats are sawn through, where they are placed suitable parts cordless tools. This approach allows the car enthusiast to quickly find the things he needs, especially in critical situations.

Portable lighting systems

As you know, there are no windows in garage spaces. During daylight hours, light enters only through a door or gate. When repairing the underbody of a car, it is very difficult to do without. Experienced motorists advise making a portable lamp.

Creating the most simple design, take a regular cartridge and connect it with electric wire, at the end of which a fork is attached. Suitable for lighting ordinary lamp incandescent or "housekeeper". The main thing is that it fits the cartridge.

To protect fragile glass, you can make a lampshade out of it. A medium-thick milky-colored vessel that perfectly diffuses light is suitable. The design is used to illuminate the most hidden places of the car and distant areas of the room.

Compact stand for electric drill

When executing various works in the garage, often used. The tool needs to be treated with care, so you need to keep it in a safe place. In addition, it is easier to drill holes on a flat and stable surface without distortions. It’s easy to make an original stand for an electric drill if you listen to the advice of experts.

First, assemble the main components of the structure:

• flat area of ​​an old milling machine;
• calibrated tube or rod;
• sheet of plywood.

A box is made from thick plywood that matches the size of the electric drill. Two holes are made in it with a drill. Next, the drill is attached to the box using special nuts. The structure is installed on the rack towards the base. A handle is attached at the top of the rack, next to the barbell. A standard ruler is installed along the base, which serves as a limiter for the unit. In this position, working with a drill is much more convenient. The holes are smooth and without visible deviations.

The useful do-it-yourself garage items shown in the photo clearly demonstrate the skill of modern car enthusiasts. The main goal of arranging a car house is to rationally distribute the working area and convenient location valuable things. Thanks to this, it will be comfortable to work, relax and even communicate with friends in the garage.

Do-it-yourself garage lathe - video

You just need this - video

We will send the material to you by e-mail

For rational use space, communications and do-it-yourself garage accessories from scrap materials are used. It is necessary to involve walls, an underground level in the process, place it indoors, and organize normal lighting.

Homemade gadgets for the garage

For comfortable operation of a room intended for car storage, you should adhere to certain recommendations:

Depending on the dimensions of the building, the area occupied by equipment, fixtures, and communications should not be more than 10–20% of the size of the garage floor.

Storage areas, racks, workbenches

In 80% of cases, do-it-yourself garage fixtures are built to store accessories, tools, and vehicle equipment. It should be taken into account that the most bulky parts of the car are sets of winter/summer tires, depending on the season.

The main nuances of these designs are:

The width of the pit should allow the driver to enter it without lighting.

Lighting and ventilation

More often used in garages parallel circuits lighting fixtures. One lamp allows you to use a specific area, several devices are turned on during a major renovation or a visit to the cellar. Minimum power consumption is ensured. Daylighting devices have a great resource.

Cars use toxic, harmful fuels and lubricants, so do-it-yourself garage ventilation devices that allow you to create air exchange are becoming relevant. The influx is organized from below:

• garage - vents in the masonry, protected by bars;
• cellar - pipe from the garage or from the street.

The hood is mounted under the ceiling of the cellar, the roof of the garage, or has the form of vents in the main walls at the highest points.

Related article:

Other useful ideas

Useful accessories for a garage with your own hands can be made from used dishes, equipment, and materials left over from construction. For example, by gluing the lids plastic cans horizontally/vertically, the owner receives convenient transparent dishes for equipment or hardware, which is always at hand.

Homemade machines

You can also assemble accessories for the garage from power tools:

• drilling - a drill fixed with clamps in a device that moves with a gear along a rack;

• cutting - an angle grinder clamped in a similar way with equipment for metal or wood;

The advantage of the machines is more accurate positioning of the equipment relative to the workpiece. The equipment turns out to be dismountable, the drill and angle grinder can be removed and used for their intended purpose.

Related article:

Hydropress

The simplest design is obtained from a car hydraulic jack. To press out/press in bearings and press/compress parts, you will need to build a frame and a removable movable stop. The frame consists of 4 channels welded to each other. At the top, the structure is reinforced with stiffening ribs (kerchiefs), and at the bottom, transverse corners are added, giving the frame stability.

The stop is pulled in the normal position to the top crossbar of the frame by powerful springs. A hydraulic jack is installed between them, pressing the stop against the lower crossbar of the frame as necessary. The press force is regulated by a jack, the dimensions of the working area are selected depending on the size of the workpieces.

And finally, a few more examples of useful things for the garage.

A variety of accessories for the private garage, designed and manufactured on our own, allow for better and more efficient vehicle maintenance. Their creation requires minimal financial costs. At the same time homemade equipment in most cases, its capabilities are in no way inferior to expensive factory analogues.

Stand for electric drill - simplify the drilling process

In a private garage, over time, more and more different tools and equipment used for maintenance appear vehicle. The owner should ensure their convenient and rational storage in such a way that the most necessary equipment were always at hand, and rarely used ones were hidden away. To solve this problem, you need to draw a basic sketch and create shelves or. Ready-made options There are many such designs on the Internet. And it’s not at all difficult to come up with a shelving system yourself.

More problems arise when you need some rare homemade items for the garage. For example, many car owners use it when servicing their car and performing various chores around the house. electric drill. Often with its help you need to do it flawlessly straight holes with axes strictly perpendicular to the plane of the workpiece. Anyone who has tried to achieve such a result knows that it is not at all easy. As a rule, the holes are skewed. Decide similar problem drill stand allows. To build it with your own hands, you need to stock up on:

• rod or calibrated tube;
• a platform from a milling cutter (manual), which has not been used for its intended purpose for a long time due to its wear and tear;
• sheets of plywood.

It is also permitted to use another suitable platform as a base for the stand. The main thing is that it is level and has areas where you can install new long guides. The function of the latter in our case will be performed, as you already understood, by metal rods or calibrated tubes. The process of building a rack is truly simple. Let's describe it.

First we cut a box from a sheet of plywood. It must be done precisely according to the geometric parameters of the available drill. Then it is necessary to secure our power tool as securely as possible for drilling holes in the box prepared for it. Fixation is best done using special wing nuts. After this, we make two holes in the box and pass tubes (rods) - guides - through them. We mount a handle on top of them. With its help, we will move the drill to drill holes vertically.

Advice. If you want to control the drilling depth, it is advisable to additionally equip the design with a quick-release clamp. It will act as a movement limiter for the drill. All the work described was done by a more or less experienced home handyman will not cause the slightest problem. And in the end we will get easy-to-use and very useful homemade equipment.

Mini knife sharpening machine - reliable and compact

Now let's try to make a device that will allow you to sharpen kitchen and any other knives. We proceed like this:

1. 1. Take an unnecessary sheet of metal (in any garage it is sure to be lying somewhere in the corner and waiting in the wings).
2. 2. We fix a threaded bolt at the bottom, and at the top metal plate weld a small corner.
3. 3. Place a nut on the bolt thread. It serves as a hinge for the lateral movement of our device. With its help you can change the sharpening angle of knives.
4. 4. We weld another one to the described nut. We got a ready-made hole for the rod in the bolt. It is easy to make from thin wire.

The clamp in the machine will be the top part of the sheet. We make two holes in it. We apply a clamp to the frame. Then we cut another hole. It must be end-to-end (common to the plate and clamp). Next, we make carvings in the bed, taking into account the length of the bars for turning. They are optimally made from artificial diamonds. There is no more wear-resistant and at the same time inexpensive product in nature. And we’ll make clamps for the beams in a couple of minutes from a piece of ebonite or plexiglass.

All that remains is to drill an additional hole on the plate, placing it away from the knife, and cut a thread for the bolt, which will be used to tighten it. A compact and high-quality sharpening tool is ready! We put it on a shelf in the garage and use it as needed. Machines made according to the described scheme can be taken with you even on a hike. These garage sharpeners weigh little and take up minimal space.

Crane beam for the garage - let's make vehicle repairs easier!

Maintenance and simple car repairs in home garage are significantly simplified if there is a crane in the room. Look at the photo below. It shows how convenient and useful a garage structure can be constructed without much effort.

We will make the transverse rod from a pipe with a cross-section of 10 cm, the supports for it from pipes 11 cm. Important! It is recommended to make homemade racks from square profile pipes with dimensions of 10x10 cm. They will provide the device with good stability. We attach the rod to the supports with M16 bolts (you can use other fasteners), fix the bevels and the base using a 10x10 cm corner.

We buy a lifting cable at the nearest construction store. We take the rollers for it from the elevator door drive mechanism. Notice! The rollers need to be well secured. This operation is best performed using a narrow (5 cm) metal strip. Lifting of objects on the crane beam will be ensured by a worm hand winch. And don't forget to attach another set of rollers to the vertical posts. They will allow you to move the crane beam throughout the garage without any problems.

DIY compressor - homemade for advanced drivers

Any car enthusiast can build workbenches, hanging shelves and other useful crafts for storing equipment. It is more difficult to make machines and special equipment yourself. But with the right approach to the matter, it is possible to cope with such tasks. Let's assemble a compressor that can be used for blowing vehicle components and mechanisms, painting a car, and monitoring tire pressure.

We will need a 10-liter air receiver (a device with a slightly larger or smaller volume is suitable), a refrigeration unit (old, not used for a long time), and also:

• adapters;
• inexpensive filter regulator (feel free to purchase the cheapest one);
• oxygen pressure gauge for the receiver;
• fastening clamps;
• hose (approximately 200 cm) designed for 20 bar pressure.

The compressor assembly process is simple. The receiver has outputs at the bottom, middle and top. The bottom one is necessary for draining oil and condensate, the middle one is for installing a pressure gauge. The flow is supplied to the consumer through the upper compressed air. We connect all the required elements to the outputs of the device and secure them with clamps. We connect the filter regulator to the receiver panel. Next to it there will be a button to start the unit. The maximum pressure of the regulator on a homemade device should not exceed eight atmospheres, the minimum - two.

It is advisable to additionally equip the compressor with an emergency valve. This inexpensive item will be fully guaranteed safe operation homemade device.

We will place the completed compressor near the wall on a rack or shelf. It will not interfere when moving around the garage, while at the same time being always at hand for the home craftsman. Advice. Old compressor Before use, it must be thoroughly cleaned of rust. And then buy aerosol can with paint and paint the unit.

Pulley for adjusting the speed of homemade machines and other crafts

We will briefly describe other popular tricks that are easily made from used tools and unnecessary things. Let's make, for example, a pulley for any machine in the garage. The material for its assembly can be textolite, metal, or plywood sheets. The last option is the simplest:

1. 1. We cut out two larger circles and one smaller one in a plywood blank. The diameter of the holes made must correspond to the cross-section of the shaft installed on the machine.
2. 2. Place all the circles on the screw, use a nut to tighten them firmly. Instead of this fastener, good glue can be used. It will securely fix all the elements into a single structure.
3. 3. Additionally, we tighten the details of the craft with screws.
4. 4. Process with a file or sandpaper homemade pulley, apply a couple of layers of drying oil on it.
5. 5. After drying, place the made device on the chuck of any mini-machine (for example, an electric drill). And we use the tool for our own pleasure, because now we can choose its rotation speed and control the load on the electric motor of the unit.

If necessary, it is possible to make a toothed pulley. To do this, it is enough to cut narrow grooves (tubules) in a small circle. This part of the operation must be completed before assembling the pulley.

If you have electric jigsaw, which is not used because the file holder is broken, does not need to be sent to a landfill. Eat small tricks, allowing you to give the instrument a second life. On its platform it is possible to assemble a simple tabletop jigsaw. We take a square of metal and solder a bolt into it. We get a new file holder! Solder it to the old holder.

Then we make a stationary desktop. We take a plywood sheet and cut it to the size of the jigsaw. We attach a stand made of wood (we use hard grades) to the back plane of the working surface, and install it on the front furniture legs. Next we mount working structure onto a suitable base plate. Use a refurbished and improved jigsaw to your health.

Any car enthusiast can make a variety of garage accessories with his own hands, using inexpensive materials and the simplest tools. Such homemade crafts by a home craftsman turn a motorhome into a full-fledged workshop.

If you plan to do independent maintenance of your vehicle in the garage, as well as perform a variety of renovation work and make your own crafts, it will be difficult to do without a workbench. It is usually made of wooden boards, which are mounted on a reliable base (profiled metal pipe or thick wooden beam).

It is also possible to make a desktop from metal blanks. They are easy to cut to the required sizes and assembled into one durable structure using steel corners and hardware (screw connections, bolts, etc.) or using a welding machine.

Making a wooden one always begins with drawing up a detailed design drawing. You must correctly assess the workspace of your garage and fit the desktop into it as harmoniously as possible. It is advisable to provide shelves and drawers (pull-out) on the workbench. They will allow you to keep all kinds of tools at hand. It is recommended to install a small vice on the tabletop.

Making a metal workbench

If your garage has shelves or racks (or you want to mount them), experts advise installing a workbench next to them.

Then you will get an excellent work area where you can do any home creativity, producing original and useful homemade products for home.

1. Assemble a tabletop from boards with geometric parameters suitable for you (for example, 200 by 10 by 5 cm), connecting wooden products together with metal ties and good glue. For a standard workbench suitable for any garage, it is enough to take 20 of these boards.
2. Make special grooves on the tabletop (on the 5th and 16th boards) for the stops. The parameters of the grooves are 2.5 by 2.5 cm.
3. After the glue has dried, the tabletop must be planed so that a perfectly flat working surface is obtained.
4. Use 80 x 10 x 10 cm bars to make legs for the workbench. Grooves should be provided in the front supports. You will insert brackets into them, which you will then connect to the beam (longitudinal).
5. Assemble the base of the table from two frames made of 10 x 5 cm boards and fix it to the support. The frames are cut into the legs of the workbench by about 2.5 cm, and then they are secured with bolts.
6. Attach the supporting walls (back and side) to the resulting structure. They can be made from centimeter plywood or chipboard sheets.

Now you need to connect the top frame to the tabletop. This operation can be carried out without problems using bolts. Don't forget to apply drying oil to the made wooden workbench and coat it with varnish. On such a table you will make any crafts with special pleasure!

Over time, any vehicle owner’s motorhome turns into a kind of warehouse where a variety of items and tools are stored. They all need to find convenient place so that each device is easy to find. A self-made rack allows you to efficiently organize the storage of tools.

You can make such a structure from metal and wood. In the latter case, use solid wood– beech or oak. Shelves and drawers made from them can withstand quite serious loads. According to accepted standards, the rack must maintain a pressure of at least 150–160 kg. At the same time, it is not recommended to load home-made structures with things that generally weigh more than 500 kg.

Wooden shelving

Let's see how you can quickly make a garage shelving unit while spending a minimum of money on purchasing materials. The work flow diagram is as follows:

1. Take a 9 cm wide board and cut it into pieces different sizes(18–30 cm). We will use these pieces as supports for the rack.
2. Make the shelves from a thicker board - 19 cm thick. To do this, you will need to cut it into pieces of the required length.
3. Mark the board for the base of the structure, indicating on it the locations of the spacers (they are usually spaced 2.5–3 cm from the edge of the base). Now you need to attach (it is advisable to use construction adhesive) the top spacer and nail the top shelf of the rack to it (with regular nails of suitable sizes). Then repeat these manipulations with other shelves and spacers. Lastly, the lower expansion element is attached.
4. Turn over assembled structure, tighten the base of the rack with spacers using screws.

Storage facility various instruments and things are almost ready. You just need to sand the rack and then apply an oil varnish to the wood (it’s better to do two layers), and then attach it with anchor screws homemade design to the wall. The places where the rack is attached to the wall are under the lowest and highest shelves.

A homemade clamping device, which is sometimes impossible to do without in home-made projects, is very simple to make. You will need:

• hydraulic jack;
• metal platform bed;
• profile pipes with a cross section of 6x6 and 4x4 centimeters (two pieces of each will be required).

The press is done this way:

1. Attach two vertical guides (4 by 4 cm pipes) to the base of the structure.
2. Weld between them (at the very top) a piece of pipe 6 by 6 cm.
3. Install another 6 by 6 cm pipe so that it moves without difficulty along the mounted guides.

Homemade garage press

The use of such a technical homemade product is elementary - place the products you want to connect on the working surface of the press, cover them with a thick plywood sheet, lower the jumper pipe with the jack placed on it. You only need to apply pressure to the jack to glue two products or your own crafts together for centuries.

But with the help of the following homemade product - cyclonic vacuum cleaner, you can always point perfect order in the garage. It is made from dense plastic or (which is better) from metal container. It must be sealed. The scheme for making a homemade product for effective garbage collection in a motorhome is as follows:

1. Make two holes in the lid of the container. Place the first one at the edge, the second one in the central part. The diameters of the holes must correspond to the cross-sections of the hoses that you will connect to the device. One hose is connected to the hole from the edge, it is intended for collecting debris, the other is needed to connect a regular vacuum cleaner.
2. In the inlet pipe of the described homemade product you need to install a plastic elbow. It will ensure the process of swirling (cyclone) air in the tank. Due to this knee, the effectiveness of such a homemade product increases, which easily and quickly absorbs small stones, lumps of dirt, sawdust and other solid contaminants. All of them will collect in the tank that you connected to the vacuum cleaner.

When heated, the material from which bottles are made mineral water and various drinks, is capable of shrinking. This gives us the opportunity to make excellent rope from such containers. With its help, you can very firmly connect various parts and assemblies in a motorhome and in the household in general.

Rope made from a plastic bottle

To make a device for making homemade cords, you need to stock up on two bolts with washers and nuts, metal washers, a piece of thin board or plywood, a utility blade and an electric drill. We make the device like this:

1. Place two washers in the middle of the board or plywood and mark their centers.
2. Drill holes in the marked centers with a drill.
3. Drill holes with reverse side(this is a mandatory procedure to ensure that there is no twisting or rotation when using the device).
4. Screw in the bolts.

The use of this craft is simple. You need to put several washers on the protruding areas of the bolts (their number determines the thickness of the rope being cut). Then you should place a utility knife on top of the washers (you can even use a piece of it) and strengthen the structure by installing several more washers and tightening the nuts until they stop. After that homemade device must be secured with clamps on a garage workbench or other work surface.

Next, we take a two-liter plastic bottle, cut out the bottom, cut a strip (very small) of the required length and place our “blank” under the knife. You need to pull the tape with one hand, and hold the container being cut with the other. From one 2 liter bottle you will get about 25 linear meters of excellent rope with high shrink characteristics.