Description of material
Construction adhesive - dry gypsum mixture gray, which is based on gypsum and chemical additives, is intended for installation and sealing of joints of gypsum tongue-and-groove slabs, gluing decorative elements and gypsum-based products. Glue is well suited for removing flaws and holes on walls.

Material consumption

Installation of tongue-and-groove slabs - 11.5 kg/m²

Conditions of work

The temperature of the air and the base during work should not be lower than +5˚С. The temperature of the mortar mixture should be from +10˚С to +30˚С.

Preparation of mortar mixture

Pour the contents of the package into a container with a pre-measured amount. clean water room temperature. Mixing ratio: 25 kg of dry mixture requires 15 liters of water. Mix everything slowly until smooth. Let the mixture sit for 2-3 minutes for better dissolution, then stir again. When stirring again, you can add water to the desired consistency.
ATTENTION!
It is necessary to use only clean containers and tools to avoid deterioration and change in the properties of the solution. It is prohibited to introduce additional water into the finished mortar mixture.

Operating procedure

The finished solution must be worked out within 30 minutes. When performing work, it is necessary to avoid sudden changes in temperature and air humidity. After assembly adhesive will be applied to the work surface, you can re-apply if necessary, but only after the first layer has completely dried. Immediately after the solution has been completely used up, the container and tools should be thoroughly washed with water.

Storage conditions

Store bags of dry mixture in covered, dry rooms on wooden pallets.
Manufacturer's Warranty
Guaranteed shelf life in undamaged manufacturer's packaging is 6 months from the date of manufacture.

Nowadays, gypsum tongue-and-groove slabs are a popular material for the construction of walls and partitions in rooms with dry and normal conditions. humidity conditions. Widely used when installing structures made of GRP. gypsum glue.

As gypsum adhesive manufacturers, we can offer you the most attractive prices. Glue for gypsum boards produced by the Peshelan Gypsum Plant is supplied in convenient packaging of 30 kg. Ready mix Excellent for installing tongue-and-groove slabs and wall blocks, frameless fastening of gypsum particle boards, insulation, gypsum stucco and other work.

Features of application

IMPORTANT! Work with the mixture must be carried out only in rooms with dry and normal humidity conditions and a temperature not lower than +5 degrees. The viability of the solution after preparation remains for 35-40 minutes.

Gypsum adhesive produced by the Peshelansky Gypsum Plant compares favorably with its analogues due to its increased strength and excellent water-retaining properties. A big advantage is the ease of preparation and use of the solution, as well as the speed of its setting.

Gypsum glue allows you to perform any complexity finishing work with the highest possible quality.

With the help of PGP, in most cases, partitions are erected indoors. Such building materials are characterized by low weight, long service life and ease of installation. To connect tongue-and-groove slabs, you need an adhesive based on a gypsum mixture, and it must guarantee excellent fixation.

The best brands

There are many means designed for fixing tongue-and-groove slabs (TGP). They all differ in composition, characteristics and quality.

The best adhesives for PGP:

• Cel gypsum It is a white powder, produced on the basis of friction sand, gypsum and various polymer additives, and must be mixed with water during the preparation process. Weber. cel gips- this is a durable composition that is ideal for working with PGP, drywall and other soundproofing materials. The prepared solution is applied using a spatula; after a short time, the surface is able to withstand significant loads.

• IVSIL PLAST It is produced on the basis of a binder component with the addition of polymer. Is the most suitable option for working with gypsum fiber sheets.
• made from gypsum sand with the addition of polymers. With this mixture you can achieve maximum high-quality installation GWP indoors.

• is produced on the basis of gypsum binder, which is perfectly combined with mineral additives, which makes it possible to carry out frameless or vertical installation of slabs. Using "Volma-montazh" you can attach gypsum elements and sheets thermal insulation material. The mixture is very easy to work with as it is simple to prepare.

• "Knauf Fugenfüller" (Fugen)- This is a dry composition based on gypsum. It is used for puttying surfaces and sealing joints; it can also be used as an adhesive for tongue-and-groove blocks. Another advantage is the relatively low cost.

• - frost-resistant product, produced on a gypsum binder base with mineral filler, modifying and anti-frost additives. The series is intended for interior work with PGP and plasterboard at temperatures down to –10° C. It is characterized by high adhesive ability, ease of use, ductility and resistance to moisture.

Advice! All products are diluted with liquid and are very economical. Mixing proportions differ, so it is recommended that you first carefully study the manufacturer’s recommendations on the packaging.

What to replace

Often special acrylic adhesive composition based on gypsum is not cheap and not everyone can buy it, especially if a large quantity is needed.

What to replace it with. Mix ordinary tile adhesive with PVA (take half a kilogram of PVA for one bucket of solution). After thorough mixing, you should get a fine, elastic composition that can be easily applied with a spatula.

Advice! Instead of tile adhesive, regular cement mortar will do.

When installing the PGP or block, the excess homemade mixture is squeezed out. The industrial composition must be used within an hour, as it sets quickly.

Interior wall partitions, in most cases, are not load-bearing structures in the house. They must have sufficient strength and good sound insulation properties. The design of the partition should easily withstand internal communications and hanging furniture.

In this article we will talk about tongue-and-groove gypsum (plasterboard) slabs (GGP). This material is used to create interior and apartment partitions. With a competent approach to construction, partitions made of tongue-and-groove gypsum boards (GGP) will meet the requirements listed above. But you need to focus on ensuring that the installation of tongue-and-groove slabs is competent!

If you neglect to comply construction technology, then the installation of tongue-and-groove partitions will end in the fact that instead of a durable monolith, the builder will end up with a shaky and uneven wall, ready to collapse at any moment.

Kruchenkov User FORUMHOUSE, Moscow.

I have a bathroom partition at home made of tongue-and-groove slabs. Apparently, when a hole was made in it for sewer pipe, something went wrong. Now, if you shake this structure by the edge with your hand, you can hear the blocks hitting each other.

You can find a lot of similar examples on FORUMHOUSE. And if the partition was originally folded contrary to existing technology, then the defects can be corrected only by completely destroying the structure.

But don’t be afraid, because the technology for constructing wall partitions from PGP is quite simple. And if you treat it with due attention, the impression of the work done will be very positive.

AlexDo User FORUMHOUSE

I worked at a construction site. The buildings of the old foundation were reconstructed. So, all the partitions were made from gypsum tongue-and-groove slabs, the work was a pleasure. Just right as a partition. Easy and quick to install. The walls are smooth. After puttying, they are ready for painting or wallpaper. The fasteners in the slab hold well. Sound insulation is also normal. But if anything happens, you can make a sheathing, lay mineral wool and finish it with clapboard or panels.

A little about the practicality of GPP

Manufacturers of gypsum boards guarantee that this material provides reliable fastening standard elements modern interior. This means that gypsum plasterboard partitions can withstand loads comparable to those on walls made of other standard materials. Wall cabinets, household appliances, suspended ceilings– all this can be easily mounted on a tongue-and-groove gypsum partition. You can expand the functionality of a wall partition made of PGP by installing metal-plastic elements into its body. water pipes(with a diameter of no more than 16 mm) and electrical wiring elements.

Grachev68 User FORUMHOUSE

You can also install doors in the tongue-and-groove without extras, install electrical wiring without any problems, and hang shelves and TV more reliably.

Tongue-and-groove slabs - what are they?

Standard PGPs come in two types: solid and hollow. The construction of solid slabs is more durable, but this material is significantly heavier than its hollow counterpart. For this reason it is not recommended
used as part of partitions mounted on the floor with
wooden joists.

Hollow PGPs provide high sound insulation (43 dB) without overloading the floor structure. Some people believe that in internal space Hollow slabs can allow all kinds of insect pests to live and multiply intensively. But such an opinion has not yet found serious confirmation.

Conventional (solid and hollow) tongue-and-groove slabs are used to construct partitions or wall cladding in rooms with dry and normal humidity levels. If the partition is planned to be installed in a room with high level humidity, then preference should be given to moisture-resistant slabs that have a peculiar greenish tint. Keep in mind that such PGPs are slightly heavier than regular solid products.

Preparatory work

List of tools for working with tongue-and-groove slabs:

• Marking cord:
• Hacksaw with a wide blade and large teeth;
• Roulette;
• Spatula;
• Drill with a nozzle for stirring mixtures;
• Bucket;
• Construction level and plumb line;
• Rubber mallet;
• Square;
• Screwdriver.

In accordance with the recommendations of the manufacturers, the length of the wall partition made of PGP should not exceed 6 m. The maximum height of the structure is 3.5 m. It is possible to increase these parameters, but the maximum strength of the partition is ensured only if the specified dimensions are observed.

The base for the wall made of tongue-and-groove slabs must be level, stable and completely free of dust. If the floor is concrete and there are differences in it exceeding 3 mm, then before starting installation work it needs to be leveled; create a leveling layer. Suitable for this mortar based on sand and cement (mortar grade - not lower than M50).

Alignment of the wall from PGP.

The solution is applied to a clean, damp floor. To obtain an ideal surface, you can create some kind of formwork and fill it with mortar precisely at a horizontal level. After complete drying, the base must be coated with a concrete primer.

If it is possible to do without a leveling layer, then the base for the future partition, as well as the junction of the partition with the enclosing walls, are covered with 2 layers of primer.

If the partition is mounted on a wooden floor, then the base must be reinforced with a strong, even beam.

Kirill147 User FORUMHOUSE

According to the technology, gypsum tongue-and-groove panels require a flat base - a screed or a separate non-sagging beam under the partition.

When the base is ready, you can mark the locations of the partitions and doorways. This is done using lacing, a plumb line and a level.

Installation of the PGP can be carried out at temperatures from -10 to +30°C. Construction material Be sure to bring it into the room in advance. This will help him “get used” to the right temperature conditions and will insure the partition from deformation (when the temperature changes, the slabs may slightly change their volume).

Installation of elastic gasket

To prevent temperature changes and deformation load-bearing elements buildings have not led to the destruction of the partition over time, the structure made of PGP should be isolated from the base and adjacent walls with a special elastic (damper) tape. Damper tape for PGP protects the wall from mechanical damage and increases the soundproofing qualities of the partition. The elastic tape is a special cork backing (at least 75 mm wide), which we will glue to the base and walls in accordance with the markings made. The boards and tape are fixed with the same mounting adhesive.

Consumables intended for installation work (building mixtures, gaskets, dowels, hangers, etc.) should be selected based on the recommendations of the PGP manufacturer. At negative temperatures installation of the PGP is carried out using a frost-resistant adhesive gypsum mixture.

Glue with a spatula thin layer applied to the prepared surface. The tape is rolled out from above and pressed lightly with your hands. The glue sets within one hour. After this period, you can begin building the partition.

Installation of PGP

The damper gasket under the tongue-and-groove slabs is covered with a layer of assembly adhesive, onto which the lower, first row of the PGP is laid. The plate can be positioned with the groove up or with the groove down - it doesn’t matter. But if the groove is at the bottom, then the ridge will not have to be sawed off to make the slab level. It is allowed to install the top row of slabs vertically (if this becomes necessary due to material savings).

When laying the first row, the vertical groove of the tongue-and-groove slab and the base of the floor are coated with glue. Special attention care should be taken to maintain vertical and horizontal levels. The slabs should be set using a mallet.

The thickness of vertical and horizontal seams should not exceed 2 mm. After installing the next slab in its place, use a spatula to remove excess glue at its joints.

Additional elements for filling gaps between solid slabs, walls and openings are easily cut from PGP using a hacksaw.

The relative displacement of vertical joints in the PGT masonry must be at least 10 cm. This is prerequisite to ensure structural strength.

At the intersection of two partitions made of gypsum tongue-and-groove slabs, as well as in the corners, the slabs are laid in such a way that their joints overlap each other. Tongue-and-groove elements that interfere with proper dressing should be cut off with a hacksaw.

After the partition is ready, it external corners it is necessary to strengthen it with a perforated metal profile and putty.

People often ask whether it is necessary to glue tongue-and-groove partitions with serpyanka. Yes, internal corners glued with serpyanka and coated with putty.

Fastening the partition to the wall

The strength of the connection of the tongue-and-groove partition to the walls and base is ensured by the installation additional elements: mounting angles, fittings or hangers. It is more convenient to use mounting angles or hangers. After all, they are attached to the slab using ordinary self-tapping screws, and to the walls using dowels. The slabs of the 1st, 3rd, and 5th rows are attached to the side walls. It is possible more often, but there must be several (at least three) fastenings. A strong base connection is created for every second slab.

During installation, direct hangers can be installed directly into the groove of the slab, having previously cut them to the required dimensions.

Between the top row of masonry and the ceiling of the room you will need a technological gap of at least 1.5 cm. It must be left and foamed polyurethane foam. After drying, excess foam must be cut off and the seam must be puttied. Between the top row and the ceiling, additional fasteners are installed at the same frequency as below.

Creating Doorways

For installing door or window openings, the width of which does not exceed 90 cm, you can make masonry without additional reinforcement. In this case, an auxiliary structure made of wooden beam, which is removed after the slabs of the top row are laid and the mounting adhesive has set.

If the opening width exceeds 90 cm, then a wooden or metal lintel should be installed above it. The ends of the lintel should protrude 50 cm beyond the opening on each side. This will ensure even distribution of the load on the partition.

The door (window) frame is attached to the partition using frame dowels and mounting foam.

Inter-apartment partitions made of PGP

Apartment partitions made of PGP, unlike interior partitions, are made double. A technological gap of 4 cm is left between the plates. First, one partition is erected, then the second. In order to enhance sound insulation, the space between the slabs is filled with soundproofing material, mineral wool, etc.

Installation of communications

The design of partitions made of PGP allows the installation of electrical wiring hidden type. Gypsum boards are strong enough to allow vertical grooves to be made into them and are thick enough to install distribution boxes. Technological cavities inside hollow PGP can be used as horizontal grooves.

If the channel chosen for laying the wire is expanded with a crown with a diameter of 45 mm, then the cable will pass through it without difficulty. The main thing is not to clog the side hole of the slab with glue during installation work.

To make it more convenient to pass the wire through horizontal channels, blind mounting holes can be made in the side surface of the partition.

Some doubt the safety of vertical gating of plaster walls. But, according to manufacturers (and the builders themselves), there is nothing to be afraid of.

From leading Russian and foreign manufacturers By affordable price. The products presented in our catalogs, and in particular the glue for pgp, the price of which depends on the type of mixture, fully comply with all quality and safety standards.

Buy glue for tongue-and-groove slabs possible in online mode directly on our website, and thanks to our delivery service, the client does not even have to leave home. All goods ordered in the store will be delivered to the specified address directly on the day of purchase.

Gypsum adhesive for pgp - features and composition

Installation adhesive pgp is a universal gypsum-based installation mixture that allows you to quickly, efficiently and reliably fasten tongue-and-groove slabs, while ensuring high quality masonry The adhesive for installation of pgp, as a rule, includes the following components:

• Gypsum.

It is the main binding element of almost any adhesive for tongue-and-groove slabs, the price of which depends on many factors. It is thanks to the gypsum binder that gypsum adhesive for installation of pgp provides the necessary strength for high-quality and reliable masonry.

• Quartz or fine sand.

This component in the adhesive for pgp, which you can buy right now, acts as a filler, significantly reducing the cost of production of this mixture and market price gypsum glue for installation of pgp.

• Chemical additives, additives, modifiers.

These components can significantly increase the ductility of the adhesive for installation of pgp, as well as extend the viability ready solution, which is important when working with large volumes of masonry.

The main purpose of glue for pgp

As the name implies, glue for pgp is moisture-resistant and regular and is used exclusively for laying tongue-and-groove slabs, which you can also purchase in our online store website. In addition, glue for pgp, which anyone can buy today, can be used for laying gas silicate blocks, and any wall blocks based on cellular concrete. Thanks to its unique composition, moisture-resistant adhesive for pgp perfectly withstands the impact chemical elements, not susceptible to fungus or mold. High-quality glue for pgp, the price of which can vary widely, is the key to the strength and reliability of the walls of the building.

Use glue for pgp during installation interior partitions in apartments or private households. It should be noted that the adhesive for pgp is moisture resistant and can be used when arranging partitions in rooms with increased level humidity, such as a bathroom, toilet, etc.

Buy glue for tongue-and-groove slabs in Moscow

Online store site, offers to buy glue for pgp and others building mixtures wholesale and retail in Moscow and the Moscow region. With us, you will find everything you need for repairs and construction at the best prices in the region. You can buy glue for pgp by adding the product to your cart, or by calling the numbers that you can easily find in the “Contacts” section. It should be noted that we deliver purchased goods throughout Moscow and the region; you can find the terms and delivery costs in a special section.