All photos from the article

Plywood is not only unique building material, but also an excellent basis for making various crafts. Moreover, for this you will need a minimum of tools - manual or electric jigsaw, the plywood sheet itself, and the result largely depends on human imagination.

Scope and advantages of plywood sheets

There are many options for using this material; in general, we can distinguish the following methods of using plywood:

• floor covering, and plywood can be used both for leveling and for insulating the floor;
• wall cladding - unlike plasterboard, plywood sheets are much stronger, although they weigh more, and are susceptible to moisture;
• arrangement of formwork when concreting foundations or making concrete blocks;
• arrangement of a solid base for soft roofing material, for example, under bitumen shingles;

• making various crafts, ranging from simple figurines to complex mechanisms, in which even the moving parts are made of plywood. In general, in the question of what can be made from plywood with a hand jigsaw, the only limit is a person’s imagination and perseverance, so the scope for creativity is simply limitless;
• Full-fledged furniture can also be made from plywood, and its strength is in no way inferior to ordinary wood.

This material also has a number of advantages:

• even thin material has outstanding strength, due to the layered structure of the material. consists of several layers of veneer, and when gluing, the fibers of each layer are located at an angle to the previous one, so that such a sheet works just fine when bending;

• due to the use of adhesive mixtures when gluing layers of veneer, plywood is not afraid of moisture;

Pay attention! For use inside the house, you should choose sheets marked FC, this means that urea glue was used when gluing, which does not contain phenolic compounds that are dangerous to human health.

• You can buy a large sheet of plywood for about 500-700 rubles; it will be enough for several dozen complex crafts. So the price can also be considered an advantage of this material.

Rules for working with a jigsaw

When making any craft, you can’t do without cutting plywood with a jigsaw (manual or electric).

There are several rules in this matter that should be followed in any case:

• The plywood sheet itself is quite flexible, so if you try to saw it without a rigid backing, it will bend and it will be difficult to adhere to the drawing line. The stand can be made from an ordinary thick board with a hole in the center for a jigsaw file; it is attached to the work table with an ordinary clamp;

Pay attention! It is important to correctly install the file into the jigsaw before starting work. The direction of the teeth should be as shown in the figure.

• when cutting plywood with a jigsaw, the tool itself is held perpendicular to the sheet, there is no need to press hard on it;
• when working, you should turn not the jigsaw, but the plywood sheet itself;
• It is unlikely that when cutting figured shapes it will be possible to do without sharp turns and sharp corners. In order to obtain a sharp turn or an acute angle, the instructions require moving the jigsaw up and down in one place, gradually turning the plywood sheet so that a small hole is formed in it in which the file will turn freely. After this, you can cut out the desired angle;
• You may also need to cut out blind holes that cannot be approached from the edge. In this case, you can simply drill a hole in it, insert a file into it, and only then fasten it to the jigsaw frame. After this, you can cut a hole of any shape.

It is not necessary to make plywood products with a jigsaw using hand tools, the same quality can be achieved using power tools.

Examples of DIY plywood products

It is physically impossible to consider all the options for plywood crafts in one article. But it’s still worth stopping at a few interesting options.

The simplest plywood crafts

As a test, you can try to make a couple of simple crafts consisting of only one element. There are many options, for example, you can try to cut out the outline of an animal from plywood and then paint it in the desired colors.

This level of complexity is suitable even for children; the work will be performed in the following sequence:

• first, the desired picture is simply printed on plain paper (or drawn by hand);
• then you need to transfer the outline of the image onto the plywood. You can do this using carbon paper or simply cut out the image and paste it onto a wooden base;

• then we simply carefully cut out along the contour; even a preschool child can make such plywood products with his own hands using a jigsaw;
• After cutting, all that remains is to sand the figure and paint it. In order for the figurine to look bright, it is advisable to use a wood primer and only then paint it.

You can complicate the task a little and try to make a figurine consisting of several elements, for example, a Christmas tree or a snowman. A plywood Christmas tree with a jigsaw will consist of 2 parts connected like a tongue and groove.

To make it, you just need to trace 2 contours of the future Christmas tree on plywood and provide grooves in both elements. In one part, the cutout is made from the top, and in the second - from the bottom, the size of the cutout is up to the middle of the height of the future Christmas tree.

After cutting, you will need to sand the surface of the plywood and go along the edge to remove burrs and smooth out any sharp edges. Dimensions of grooves in the bottom and upper parts must correspond exactly to each other.

Pay attention! Many do-it-yourself drawings of plywood products using a jigsaw can be found on the Internet, for example, on our portal. This is much more convenient than drawing yourself.

After mastering figure sawing, you can move on to crafts consisting of several parts. As an example, we can give a figurine of a snowman, consisting of a torso, a head, two legs and arms; all these elements will be connected to each other with an ordinary thick thread.

The basic principle remains the same - we draw up a drawing, cut out individual parts from a plywood sheet, and then move on to combining them. In addition to working with a jigsaw, you will have to drill thin holes in the plywood in order to thread the thread through them.

A plywood snowman is assembled into one piece using a jigsaw; you can put a small bright scarf around your neck. As is the case with other crafts great value has the color of the figurine, the coloring should leave the impression that the snowman has just been brought into the room from the cold.

The options are relatively small and simple crafts There are many, and you can always make drawings of plywood work with a hand jigsaw yourself or simply find them on the Internet.

Making the task more difficult

If you have a jigsaw, you can try to take on a larger task. It is relatively easy to make an elegant frame for a picture from plywood, and the picture itself can be made entirely of plywood.

A picture made of plywood can be easily obtained by combining light plywood and a dark background. You just need to cut it out on the sheet light color the desired outline and then fix it in a frame on top of a dark background. Due to this, it is achieved desired effect, externally, such paintings look no worse than ordinary ones, even more unusual, because traditional painting is more widespread.

As for the technology, to make a picture you only need a template with the location of the cutouts. You can make it yourself; to do this, just make the image you like black and white, add contrast and manually mark the position of the cutouts. Number of plywood layers different shades limited solely by the skill of the author.

Thin plywood is also suitable for making a frame for a picture or photograph, and frames made from plywood with a jigsaw can also be solid, that is, cut from one piece of plywood. The simplest plywood frame is a closed plywood contour (rectangular, square or oval shape) With figured sawing along the outer perimeter.

On such a frame you can attach various plywood figures, thereby creating the feeling for the viewer that they are just sitting down to rest. You can limit yourself to a simple neutral pattern.

Pay attention! If you plan to make a photo frame, then it makes sense to focus on back side so that the frame is stable on the table.

Mechanical plywood crafts

Making such a craft from scratch is a rather complicated undertaking, and the main difficulty will lie in the design. For example, a machine made from plywood with a jigsaw has more than a dozen parts complex shape, a deviation of even 1.0-1.5 mm will make it impossible to assemble the model, so drawing up a drawing is the main difficulty.

You can simply purchase a ready-made set of factory-made parts, but it is much more interesting to cut out all the parts yourself using the drawings and assemble the car model with your own hands. All you need is patience and perseverance; after all, there are a lot of parts, and their shape is not the simplest. The remaining steps are the same - sanding, application acrylic primer and painting.

Another option is to simply create an original case from plywood, for example, for wall clock, leaving only the dial visible. It will look original, connect individual elements can be made into one whole using glue.

More complex products with moving elements also made of plywood can be made from plywood. In this case, it is better to purchase or download drawings of plywood products using a jigsaw; it will be difficult to make them yourself, since you will also need to calculate the number of teeth and the size of gears, shafts and other moving elements; this is difficult to do without the appropriate skills.

Plywood furniture

Such furniture weighs little, but in terms of strength it is not inferior to analogues made from solid wood and even surpasses them (due to the layered structure of the material). To make an original table, bench or chair, you only need a jigsaw and a thick sheet of plywood of the appropriate size.

You can prepare your own drawings of plywood furniture with a jigsaw yourself; the difficulty arises at another stage - it often becomes necessary to bend a plywood sheet.

There are 2 ways to solve this problem:

• Having steamed the bend, you can soak the plywood for 20-30 minutes hot water, and then try to give it the desired shape;

• in the place of the bend, cuts can be made at equal intervals, not reaching the edge of the sheet by 2-3 layers of veneer, then the plywood is bent, and the place of the bend is coated with glue.

It is not necessary to make furniture entirely from plywood. For example, the tabletop can be made of plywood, and the legs can be made of ordinary wood, the sides of the bench can also be cut from a sheet more than 10 mm thick, and the seat and back can be laid from boards.

In conclusion

Ordinary plywood sheet in capable hands can turn into a real masterpiece. The only limit when working with this material is the author’s imagination, so you can make anything, from simple animal figurines to copies of world-famous architectural structures.

It is also important that the only tools you will need are a jigsaw and emery, so no special expenses are expected. The video in this article shows the process of making an original painting from plywood.

In the comments to the article, you can always clarify any questions you have about working with plywood.

What is plywood carving? This question has probably arisen among many novice masters. Plywood carving is a decorative and applied art.There are several types slotted thread on plywood:

• openwork;
• cutting out an image on a painted plywood sheet;
• sawing;
• combination (for example, openwork method + sawing).

Where to start

• A plywood sheet is used as a blank, the surface of which should not have any defects. As a rule, first-grade and second-grade sheets of glued wood veneer are used for these purposes.
• In order to carve plywood with a jigsaw, use a material whose thickness is in the range of 3-12 millimeters. The size of the sheet of glued veneer depends on the image that should be applied to it.

Important to know! A sheet of glued veneer should be cut along the grain, not across. Therefore, the base must be cut in such a way that the lines of the picture are located along the outer layer.

• Before painting the workpiece, it is necessary to clean the plywood using files. This process should occur along the edge. Otherwise, the sheets of glued veneer will begin to crumble.
• Using sandpaper (use fine-grained and coarse-grained), sand the surface of the sheets on which the picture will be cut out. Begin to process with a fine-grained sandpaper. The result is smooth surface. After sanding, the base should be wiped with a damp cloth (this will remove working dust).
• For painting use dark colors: blue, gray, black. For this you can use ordinary paints: gouache or watercolor. However, over time, such paints fade, so it is recommended to use nitro paint. This coloring composition adheres well. This composition dries in about half an hour.

Important point! Nitro paint, acrylic dyes and gouache are only suitable for drawing contours. To apply a shadow picture, you need to cover the base with an aqueous solution.

• After the design is cut out, its edges should be carefully sanded using sandpaper.

In order to carry out quality carving on plywood, you need to think about the drawings in advance. The selected design can be printed on a printer or drawn with your own hands directly on a plywood sheet. They also make carvings using a jigsaw on plywood according to a template.

You can also use tracing paper. Through it, a picture is transferred, which is applied to the workpiece. This method is considered the simplest.

Important! Every novice craftsman must remember that the process of creating plywood carvings with a jigsaw begins with drawings. Carving plywood with a jigsaw, the drawings and templates of which will correspond to the plan, will turn out to be the most attractive.

Tools required for work

First of all, it is worth noting that the tool for cutting the material should be chosen from steel. Steel cutters are considered more durable. Drills, pieces of wire, needle files or reamers will do.

It is also worth paying attention to sharpening. The tool must be well sharpened, otherwise the plywood will become unusable.

You should first make a small hole into which the chips will fall during the cutting process of the material.

To carry out slotted carving on plywood with a jigsaw/laser carving on plywood, you will need flat, semicircular and triangular cutters.

Important! The tool should be installed at an angle of 45 degrees.

So, to work you will need:

• sandpaper(coarse-grained and fine-grained);
• file, brace, jigsaw;
• coloring composition, varnish;
• incisors and tampon.

How to make a blank

Before you start making the workpiece, you need to prepare workplace. The table on which the workpiece will be made must be durable. If during work the table accidentally moves out of place or shakes, then all the work will go to waste. The lighting should be good.

Stages:

1. The incisor is clamped with one hand and the blade is held with the other. In this case, the handle of the tool should rest against the palm. The little finger on the second hand controls the angle of the blade.
2. When cutting out curved lines, no tilting is done. The pressure exerted on the tool should be controlled. This is necessary to ensure that all lines are the same width.
3. After the image has been applied, several layers of varnish should be applied. However, the second coat of bark should be applied only after the first coat has completely dried.

If the thread cut into plywood with a jigsaw corresponds to the drawings, it means that the master did everything correctly.

Openwork method

Work process:

1. The drawing is applied using a pre-prepared template.
2. Sawing is carried out. Then mark the guide holes.
3. Carry out cutting along the internal contour.
4. The cut out elements are sanded using sandpaper.
5. Securely secure the workpiece. Then mark the places where holes need to be made. To do this, use a brace. If you need to make small holes, use an awl.
6. After the work has been done, the picture is sawed off along the contour. The product is then cleaned and polished.
7. Sawing is carried out using an electric or regular jigsaw.

Sawing

It is worth noting that the work process is practically no different from previous methods. However, many believe that this method is the simplest and most understandable. Sawing is carried out using a regular jigsaw or an electric one.

It is worth noting that in factories, elements are cut out using a laser.

In order for the cutting to be attractive, you must be able to work with a jigsaw.

Process:

1. The selected image is applied to the plywood sheet. A novice craftsman should first choose something simpler, where he will not have to cut out internal holes with smooth lines.
2. The workpiece is securely fixed using clamps. If they are not there, then you can do without them.
3. The saw should be perpendicular to the plane of the base. You need to cut evenly. The hand should move in the direction of the sawed outline.
4. The product is sanded using sandpaper. You should also take care of the edges.
5. The product is painted or varnished.

Why use plywood to create carvings?

Currently, such material is actively used not only in the manufacture decorative elements, it is also used in the manufacture of furniture, subfloors, wall decoration, ceilings and more.

This material is chosen for many reasons:

• not afraid of moisture;
• temperature changes negative impact do not apply to plywood;
• low cost (unlike solid wood, the price of a plywood sheet is much lower);
• ease of operation;
• light weight.

It is also worth noting that for the manufacture of crafts and pieces of furniture where carvings will be present, it is necessary to choose first-class or second-class plywood. The remaining varieties (3,4) are not suitable for such creativity, since there are cracks, chips, and knots on the surface.

In conclusion

If carving on plywood was carried out strictly following the instructions, while taking into account all the features of cutting and material, then the result will be a product that will deserve everyone's attention. With the help of such crafts you can not only decorate the interior, but also give it as a gift.

However, in addition to the fact that as a result you can get beautiful product¸ The process itself is very interesting and exciting.

IN lately Various inscriptions and individual letters made of wood or plywood are becoming very popular. They are used in a wide variety of situations. You've probably seen similar products in some magazines dedicated to interior design, in gift and accessory stores, in wedding boutiques, in offices offering organization of holidays. Often such decorations appear in television projects about renovation and interior design. In addition, you may have seen similar signs in stores.

What are these letters and inscriptions?

Essentially, it’s just plywood from which words or individual letters are cut out using some tool (more on that later in the article), painted in a certain color and decorated various decor(paper, rhinestones, threads, etc.). But, most often, it is just an inscription (or letter) without any additional decorations.

These products may have different fastening formats. In order to hang them on the wall, you need to provide special hooks on the back. To be placed on a flat surface - on a table or on a shelf - they are mounted on a stand made of the same plywood or glass. In addition, they are often used without any additional fastenings. They just bet on flat surface, and the inscriptions or letters stand due to the thickness. This is true for plywood products with a thickness of 12 mm or more.

Who needs such letters and words and why?

The question is correct and logical. After all, some readers might still not understand what kind of business this is. Who needs all these letters made of some kind of plywood? Where to use them? Why buy something like this at all? And who are these people - the buyers of “plywood words”? Let's look at these seven questions in order.

Where can all these words and letters made from plywood be used? Here are a few illustrative examples. And then you can figure it out for yourself.

Inscriptions for interior decoration. Despite the apparent simplicity of these products, they look simply amazing in real life. Especially if they are painted with high-quality expensive paint. Such inscriptions can be placed on a rack, on bookshelf, on the fireplace, on the desktop. They can decorate the walls of a house or apartment, giving the interior an unusual, modern and very stylish look.

Another area of ​​application is creating a background for photo shoots. Now you can take pictures not just at home or in the park, but in a specially equipped studio. Just don’t confuse them with traditional komorkas, where they take passport photos in 5 minutes. It's about modern studios, where there is not only the different classes and destinations, but also various decorations to create a beautiful background. Words (and other figures) made of plywood are actively used by photographers to create thematic backgrounds for photo shoots.

Need more examples? Fine. Weddings, birthdays, anniversaries, corporate events. Everywhere there are letters and words made from plywood sheets, written in fashionable fonts and painted in stylish colors, will be a wonderful holiday decoration. No worse than the already pretty boring balloons and flowers. And for the birthday boy, you can generally prepare a gift by cutting out his name and age, for example, from plywood. Such crafts are especially loved by young mothers who are happy to buy these paraphernalia to celebrate their child’s birthday.

You can also make stylish inscriptions from plywood for restaurants, bars, cafes, shops, offices, etc. If you look at the world with your eyes wide open, you can understand that inscriptions and letters made of wood can be used almost anywhere where you want to add style, design and beauty.

How to organize a home business for making inscriptions from plywood?

This business has three components - equipment and raw materials, the manufacturing process and the search for distribution channels. That's all. It seems that everything is simple. Actually... it's simple.

Very often, such a business is organized by those people who are faced with the purchase of such accessories. When you need one such inscription, then, no problem, we order and receive it. But when a lot of letters or inscriptions are needed, many begin to think about the high cost of these products. And they are really not cheap.

Potential buyers begin to study the issue and come to the conclusion that it is more profitable (and more interesting) to make such inscriptions themselves. Right at home. Moreover, you can get by with simple equipment, and the raw materials are quite inexpensive. So, step by step, buyers turn into entrepreneurs.

Let's move on to organizing a business. Let's start with equipment and raw materials.

There is only one raw material in this matter - plywood. True, sheets of different thicknesses will be needed for different purposes. Just don't use it too much thin plywood(less than 6 mm) - it can quickly lose its shape, and therefore its presentation. In addition to plywood, you will need paint. You can use different types, but many “experimenters” end up choosing acrylic. This paint applies better, dries faster, holds tighter and looks very, very presentable.

Plywood costs about 500 rubles per sheet of 1.5×1.5 m format. Paint - depending on the manufacturer - from 150 rubles per liter.

Equipment. Everything here is very interesting. Each master cuts letters from plywood in the way that seems more convenient to him. Or the one that at the moment enough money. Because the price range is from several hundred rubles to hundreds of thousands.

The simplest tool is a jigsaw. Regular hand jigsaw. Even with its help you can cut out the most bizarre shapes. Including letters and entire inscriptions. There are a lot of advantages - accuracy, ease of use, low cost. Such a tool is worth even the most high quality no more than 1000 rubles. And non-branded models can be purchased for 150-200 rubles. The same goes for consumables– files – they also cost 100 rubles for a whole set (expensive ones – the same price per piece).

Among the disadvantages of a manual jigsaw, the following can be noted. Firstly, the ability to work only with small inscriptions. You won't be able to cut a large surface with a jigsaw. Because it will be simply impossible to crawl up. Secondly, not every hand jigsaw can easily handle plywood with a thickness of more than 10-12 mm. It will work, of course, but it will take a lot of time. And you won't need a single spare file. Thirdly, manual cutting with large volumes it is a very problematic task. Whatever one may say, it’s difficult to work with your hands. And it won't happen quickly.

Therefore, the second option is an electric jigsaw. Has almost all the benefits of a regular jigsaw, but significantly speeds up production process. In addition, it allows you to saw even very thick plywood - 30-40 mm. The disadvantage is the price. Good model(Bosh, Makita) will cost 4000-6000 rubles.

Another option is a jigsaw. There are two types. The first real machine, which is similar in size and appearance to a machine. Such units cost from 15,000 rubles or more. For those who want to save (both money and space in their home), there are also desktop jigsaw machines. They look like sewing machine. And in size, about the same. Prices start from 3000 rubles.

Well, the most expensive option is automated milling machine. Price tag – from 150,000 rubles and more. But it seriously saves time and performs cutting flawlessly. In addition, it can be used not only for plywood, but also for wood, glass, acrylic and even metal. All this opens up new prospects for business development.

In general, choose the option that suits you. A lot here depends on your financial capabilities, as well as on the type of home you have. Well, it is very problematic to place the machine within an ordinary apartment.

Now about the manufacturing process. It is clear that at the last stage the inscription is cut out with a jigsaw or on a machine, after which it is sanded and painted. But another question arises - where does this inscription even come from?

First you need to install any graphics program on your computer. Ideal option– Photoshop. Moreover, today it has become available. The license costs about $20 per month. Next, download various fonts. Of course, we are interested in beautiful designer fonts. Just make sure that they are free (this will avoid problems in the future). Or buy good quality fonts.

The further process is simple and clear. In the program we create an inscription of the required size and using the desired font. We add some elements that will become part of the composition. Be careful - the letters and all elements of the inscription must be a single whole. That is, all elements must have points of contact. Otherwise, it will be impossible to cut out a whole word.

Next, print out the resulting template. You may have to print it on several sheets if the writing is large and long. We take plywood, apply our template, after placing carbon paper. We secure everything so that the inscription does not move around on the plywood. And we transfer everything to a blank for the future inscription. We remove the stencil and carbon paper. All. The material is ready. All that remains is to cut and paint.

Now about the implementation process. Of course, at first no one knows about you. Therefore, your initial goal is to shine. Wherever possible. Make some cool signs. Take good pictures. It might be worth inviting a great photographer. Create a portfolio. And then – leave your portfolio on message boards, on thematic websites and forums, on special platforms, such as the “Masters Fair”. Take a tour of gift shops, wedding salons, and offices that organize holidays. Offer them your products. After some time, the first orders will arrive. And then word of mouth will work. This will provide you with constant orders. And a stable income. Good luck!

If your new hobby is sawing out various decorative elements, burning or carving wood, then our advice would be to start with a material such as plywood.

There are several significant reasons for this:

Plywood is quite easy to work with.

If it's in your hands good tool, and you'll start with the figures small size, then making them will only take you a couple of hours.

The material is universal in use, so you can make literally anything you want from it: furniture, toys, small decorative elements.

All this can be a wonderful addition to the interior of your home.

Features of working with the material

What is a plywood sheet? It consists of several sheets of veneer, which are connected to each other using glue.

Important: plywood can be different types: based on beech, birch, pine.

Not only the quality depends on which sheet you choose. finished product, but even its structure and color.

If you are going to cut out various figures using a jigsaw, then you need to choose the highest quality types of plywood.

They are particularly durable, which guarantees that the plywood will not crack, ruining the entire appearance products at the most unpredictable moment.

If you are going to start working immediately, immediately on the day of purchase, then choose only dry sheets of wood.

They won't break the jigsaw blade every 10 minutes.

To work with plywood, you will need to acquire a number of tools.

In principle, they are always the same for all types of products, so you only need a one-time investment:

• Jigsaw
• Jigsaw files
• Hand or electric drill
• Ruler
• Grinding machine
• Burner.

Framework

If you want to beautifully decorate your home or give it to someone close to you original gift, make your own plywood frame.

The preparation process will not take you much time, because you just need to get the necessary materials.

Pay attention!

They are standard for all cases, and we have already mentioned them before.

We will offer you master classes on light crafts made from plywood. You can make either a regular straight frame or plan various patterns and figures on it.

First you need to make a template, and after that you can cut it out, trace the contours with a pencil on the plywood and begin the manufacturing process.

This stage is not only the most responsible, but also the most exciting. If you put a piece of your soul into your work, everything will definitely work out. The finished structure must be opened with varnish. Ready!

Doll furniture

This task will be a real test for parents.

Pay attention!

The so-called test of acquired design skills.

Feature of creation doll furniture is that children do not tolerate falsehood at all.

If they see that the furniture is not worked out in detail, but instead kitchen stove for your favorite doll you brought an ordinary block rectangular shape, then you simply cannot avoid serious grievances and childhood disappointments.

The second feature of making such a craft from plywood using a jigsaw is that all this furniture must be carefully worked out with sandpaper or a grinding machine.

Your child will constantly come into contact with these self-made toys, and if the edges are poorly processed, they may get hurt.

Pay attention!

Well, the last feature of crafts made from plywood and the house is that the materials for such furniture must be absolutely non-toxic and normal for constant contact with the child, because he can drag it into his mouth or take it to bed with him.

This is not a simple applique or paper craft, so you need to take the matter seriously, following a whole list of actions that need to be completed.

Carrying out work from plywood

How simple furniture is made in detail, and then assembled into one piece of furniture, so do-it-yourself plywood crafts should be done separately.

To do this, first of all, prepare special drawings of plywood crafts, on which you will specify the dimensions of all parts and their fastenings.

Take a ready-made plywood sheet and attach a paper part template to it.

Trace the part with a pencil and plan out the outline with a jigsaw.

After this, each part must be cleaned with sandpaper or a grinding machine and only then the piece of furniture must be assembled.

When you are done with the entire set, open it with varnish.

Below are provided different options and photos of plywood crafts. Choose the one you like.

Photos of plywood crafts

Wooden crafts, lovingly made by craftsmen, have always aroused admiration and were very highly valued. Of course, wooden figures and relief carving are crafts that can be mastered with effort and honing your skills.
Here you need not only an instrument and a teacher (purchasing an instrument is not a problem, and in principle finding a teacher as well), but also a great desire, and given the time pressure in life, it is not always possible to put everything together. But there is also a more “budget” hobby that requires minimal equipment and not much free time.


This is the so-called flat carving, and a material that is perfect for crafts (for example, it’s a fairly inexpensive thing, and creating hand-made masterpieces is a very simple and useful hobby.

What do we need

Cutting plywood with a jigsaw was once cultivated in schools. Now, taking into account the possibilities of modern industry, openwork lattices or boxes are as easy to purchase as a bottle mineral water, but, alas, you will not have a feeling of pride from the fact that a beautiful thing was made with your own hands.
Carving plywood with a jigsaw is not difficult, experience comes quickly. By breaking a few nail files, you will gain the necessary skills in pressing the blade.
And to implement all this you will need three things:

• Hand jigsaw with files. An electric one is also possible, but both it and its consumables will cost much more than a manual analogue and ordinary nail files;
• Clamps, which can be used to secure the material to the table (of course, you can use a vice, but why do you need a vice in your apartment);
• And the material itself - .

The jigsaw itself, like everything ingenious, is a very simple tool. It consists of a crescent-shaped frame, a wooden handle and two screw clamps that hold the file in a fixed and tensioned state. To do this, many nail files have a tension screw on top.
A few words about the files themselves. These are metal blades, curved somewhat in an arc with sharp teeth that allow cutting. Shaped cutting plywood with a jigsaw and is achieved with narrow blades that allow cutting in almost any direction, as a result of which fancy patterns appear in the material. The files come in ten sizes and lengths from 11 to 13 cm.

Let's get to know each other better

Interesting to know! The narrower the file and the fewer teeth it has, the thinner and more accurate the cuts. But, like any medal has two sides, this plus is balanced by a minus: what thinner saw, the more fragile it is. Therefore, when working with multi-layer plywood, it is recommended to use coarser blades and make adjustments by sanding.

Preparing for work

The patterns for cutting with a jigsaw on plywood can be anything. Very often, only the outline of the product is cut out, and coloring is done by hand. As a result of such actions, the craft has a figured contour and a painted surface.
As an example, we can cite the canvas kitchen clock, which can be in the form of a teapot or fruit. And the color accompaniment can be either natural, or vintage, or any style that you like best.
Therefore, before starting work, the following actions are performed:

• The drawing of the planned craft is transferred to the plywood. If it is only an outline, then it is easier to transfer it using a prepared paper pattern. If you want to reproduce a complex pattern, Arabic writing or something exclusive, then you will need pre-prepared stencils, or established application techniques or copy paper;
• Correctly insert the nail file into the jigsaw. Cutting from plywood with a jigsaw will be convenient and most productive only when the saw teeth point forward and down. This is easy to determine both visually and by touch with your finger;
• In addition to a jigsaw, they may be useful for carrying out work: screwdriver and wood drill, with a diameter equal to the thickness of a nail file, sandpaper and a set of needle files, and a pencil, where would we be without it. Sometimes a sharp knife-cutter and chisels are mentioned for curly processing of multi-layer plywood. But if you don’t have experience, then start with small and simple tasks that allow you to solve the problem with a minimum of tools;

Pay attention! During the work, it may be necessary to cut in a closed circuit. In this case, a hole is first drilled, a file is inserted, then it is fixed in a jigsaw, and after all, the cut is made. This is how we cut out curly closed contours from plywood with a jigsaw.

• Next, the workpiece is rigidly fixed to the table with clamps. In literature and on many sites reflecting creativity, you will find mention of the table dovetail. Outwardly, it looks like a stencil of a large clothespin. It is planned that the tail will come out, and the cutting will be carried out in the prepared sector, while clamps will secure both the table and the workpiece.

Cut it out of plywood with a jigsaw. We promised you that the skills will come quickly, and so they will, here are a few useful recommendations:

• The sawing process occurs when the jigsaw moves downwards. The tool itself moves strictly vertically; when moving downward, force is given and the file moves forward. Any deviation from the vertical axis can lead to jamming of the blade and breakage;
• When working with a jigsaw, you need to learn one rule - it is the workpiece that turns, not the jigsaw. At the same time, the sharper the turn, the more careful the movements;
• Cutting out plywood with a jigsaw has its own sequence: first you work on the inner contour, and then the outer, although in in this case variations are possible;
• Any instruction will tell you that it is necessary to monitor the temperature of the canvas. If the blade overheats, then it must be allowed to cool, otherwise the price of the issue is a broken nail file.

In conclusion

Similar materials