Summer and autumn delight gardeners with abundant harvests. Unfortunately, it is impossible to store crops at home for a long time. To process it, you will need a juicer. You can buy it, or you can make it yourself from your used one. washing machine. To do this, you need to have metalworking and welding skills.

How the juicer works

The way a juicer works is very simple: it breaks the integrity of apples, grapes, apricots, etc., dividing them into a liquid fraction - juice and dehydrated fiber - pulp. The main components of the juicer are as follows:

• Hopper into which fruits or berries are loaded
• A chopper that destroys the peel and structure of the fruit. Rotating knives or a drum grater are used.
• Device for squeezing juice. This can be a press or centrifugal force arising in a rotating drum.
• A filter separating the liquid fraction and cake.
• Stand for bottles or containers for collecting juice

The simplest juicer is a construction mixer clamped in the chuck of a high-speed drill.

Materials and tools

The design of a self-made juicer, which is more complex to manufacture, but also produces higher-quality products, is built on the basis of a used front-loading washing machine.

At the first stage, you need to remove nodes that are no longer useful:

• pump;
• water heating system;
• control system;
• water supply and drain pipelines and valves;
• back wall and bottom.

General view of the device

Materials you will need:

• Two springs to cushion the drum. They are designed to balance the increased horizontal centrifugal force, since the device will be operated with the hatch upward.
• Two strips of metal mesh 300*60 mm.
• Container for storing juice.
• Drain pipe.
• Plugs.
• Fasteners

Tools needed:

• high-speed screwdriver or drill;
• angle grinder;
• welding machine;
• set of hand tools.

You will also need a workbench with a vice.

Juicer from washing machine

To dismantle, the machine must be placed on the rear wall and secured. The following should remain on the frame:

• loading hatch;
• sealing collar;
• drum;
• electric motor and drive.

• remove the belt that rotates the drum from the pulleys;

Pulley removal

• remove shock-absorbing springs and other parts that interfere with removing the tank;
• remove the sealing collar;

Removing the cuff

• remove the drum and tank;

Removing the drum and tank

• clean them of dirt, rinse with vinegar.

You should also remove from the tank heating elements, sensors and other equipment and seal the remaining openings with rubber plugs.

Now comes the stage of finalizing parts and assemblies:

• Assemble the tank and secure it in its original place.
• Install the sealing collar.
• Weld the holes in the drum.
• Remove the ribs inside the drum. There is no need to remove the fasteners.
• Drill 100-200 holes in it with a diameter of 1 - 1.5 mm.
• Inside the drum, secure the mesh strips with self-tapping screws between the places where the ribs are attached.
• Attach shock absorbing springs.
• Connect the electric motor to the network via a switch. The engine power must be at least 1-1.5 kilowatts.
• Finally secure the device on a horizontal base with the hatch facing up.

The test run should be carried out without downloading. When rotating, the drum should not touch the walls of the tank. If everything is in order, you need to place a juice container next to the drain pipe.

Fruits placed in a drum will break into a pulp, hitting the nets, the ribs and each other. Centrifugal force will force the juice through the holes into the tank, from where it will flow into the storage tank.

How to make a loading hopper and pusher

For dosed loading of fruits, you will need to make a bunker. It can be made from a piece plastic pipe with a diameter of 100 mm. It is fixed obliquely so that the fruit rolls onto the edge of the grater. The hopper is attached to the device body with aluminum or steel corners bolted

Pipe for making a bunker

The pusher can be made from a birch cutting for a shovel. A circle of plywood with a diameter 5 mm smaller than the diameter of the pipe is attached to the lower edge. A transverse stop is installed on the top one.

Grain crusher from a washing machine

An industrial grain crusher is not cheap. If a home handyman has plumbing, electrical and welding work, and in the pantry there is a broken activator-type washing machine - it is quite possible to convert it into a grain crusher, or, as they say, a grain crusher.

Grain crusher from a washing machine

Required materials, tools and design

To make a grain crusher you will need

• Oka washing machine - 1 pc.;
• knives for crushing grain - 3 pcs.;
• grid with a cell of 2-3 mm;
• tin and rubber for gaskets;
• sleeve;
• flange.
• segment plastic pipe diameter 100-150 mm

Tools and equipment that will be useful:

• drill or high-speed screwdriver;
• a set of hand tools;
• angle grinder or grinder.

Changes made to the design of the machine boil down to replacing the activator with flat knives with curved ends. The grain is poured into the hopper (2), which serves as the washing machine tank. Rotating, the knives (4) crush the grain and throw it onto the calibrating grid (7). Grain particles smaller than the grid cell pass through it and fall into the funnel (8) and then into the storage tank. Particles that do not pass through the grate return to the knives in a stream of grain and are crushed again.

Structure of a grain crusher

During preparation, you will need to remove the plastic activator cover. The knives are made from steel strip 3-4 mm thick; their ends must be bent into opposite sides so that they do not touch the walls of the tank. The hole for mounting on the shaft must be drilled exactly in the middle of the strip, otherwise it will be poorly balanced and cause wobbling during rotation. The flange on one side is put on the pulley, on the other side it has a threaded rod for attaching knives. You should also prepare a rubber gasket and a square patch made of tin to prevent grain from getting into the drive.

Assembling the device

Grain crusher - top view

Assembly begins by attaching the chopper blades to the flange. Next, the bushing, passed through the gaskets, is attached to the pulley. The patch should be attached to the tank body in such a way that the knives do not touch it when rotating.

The next stage is the installation of a funnel for collecting and discharging crushed grain. The drain located at the very bottom of the tank will not be converted. The sequence of operations is as follows:

• Using a chisel or grinder, bring the drain hole to a diameter of 120-150 mm.
• Insert a piece of pipe into the hole and secure it.
• Take the pipe to the side and direct it into a storage tank.

The next stage is the installation of a separator grid. To do this you need:

• Mark the installation line at the bottom of the tank so that it is 1-2 cm from the blade rotation zone.
• Cut the grid from the mesh so that it is placed perpendicular to the bottom of the tank and fits snugly to both the bottom and the side walls.
• Secure the grille with self-tapping screws to the surface of the tank. For reliability, you can use clamping strips made of thin strips cut from a sheet of metal.
• The cracks should be coated with a compound like “ cold welding"or silicone sealant.

Before the test run, you must securely secure the device to prevent it from tipping over or falling. The trial run is carried out without grain. During this process, it is necessary to ensure that

• the knives do not touch the bottom of the tank and the sealing gasket;
• the knives are well secured to the bushing, and the bushing is to the flange;
• there is no beating of the knives due to imbalance.

If runout is detected, balancing is carried out by balancing the knife along the line of the hole. Small holes are drilled in the lowered part until the parts are balanced.

After a successful test run, you need to make sure that under the outlet pipe there is storage capacity. Next, you can pour approximately 5-7 liters of grain into the tank, close the tank with a lid and turn on the machine at maximum speed. To reduce dust, you can put a blanket over the lid.

The new life of the washing machine as a grain crusher has begun. Bon appetit to your pets.

Other ways to make juicers

If skills home handyman If they don’t allow you to make a juicer from a washing machine, or you simply don’t have such a machine at hand, you can process the crop in another way.

A construction mixer used to mix solutions or paint is suitable for crushing fruits. Several holes are drilled in its lower part, and bolts protruding 10-15 mm are screwed into them. The fruits are crushed in a bucket, then the mass is placed in a woven bag and placed in a press.

Chopping apples with a mixer

To make a press, a large one is suitable. enamel pan. Holes should be drilled in the bottom of the pan at the same frequency as in the colander.

Juicer from a saucepan

The bag is placed in a modified pan and placed under pressure. Apple or pear juice flows out through the holes, the pulp remains in the bag. Instead of oppression, you can use a hydraulic jack.

Using a jack to squeeze juice

This method provides less productivity and depth of processing of raw materials than the manufacture of a full-fledged homemade juicer used for processing apples.

Is it possible to make an apple juicer with your own hands? Of course, moreover, anyone can cope with this. The material below will be of interest to summer residents, people who have small gardens and love apple juice in unlimited quantities throughout the year.

Features of the device

If we are talking about preparing juice from seasonal fruits in quantities of up to 2 liters, then electric auger juicers, available on the shelves of any large hardware store, will help here. But if you need to squeeze juice out of large quantity apples, but electrical household products are not suitable, then your brain and available materials come to the rescue. For large quantities of apples, a highly productive and reliable juicer is needed.

One of the main advantages homemade apparatus is in minimal or no capital investment, if all available materials are available. In case of malfunction or breakdown, it is possible to repair the device yourself.

Before you start making a homemade juicer, you need to understand the principle of its operation and know what elements must be provided and installed during its creation:

• first required part– this is a chopper;
• in fact, the press, which squeezes the juice from the fruit;
• something like a filter in this case you can use gauze, a sieve, a colander, or make it homemade using a drill and stainless steel;
• The last required element is a container in which freshly squeezed apple juice should be collected.

Species

Homemade juicers are divided into 4 types: mechanical, pneumatic, hydraulic and electro-hydraulic. The most commonly made at home are juicers. mechanical type. Such models are large in size and are divided into two types: centrifugal devices, where the apple is crushed in a centrifuge, and then a press or screw products come into operation, which produce the necessary juice through complete processing of the fruit.

The big advantage of auger devices is that they give maximum quantity juice, and after finishing work there is no need to clean and rinse them, like centrifugal ones. Please note that the option with a screw apparatus is more expensive and labor-intensive to create, requiring the use of a machine and certain knowledge.

How to do it yourself?

One of the most simple ways quickly creating a juicer is an old one folk method. For this you need a wooden or metal container, a sieve and a manual screw press, under which the fruits are poured, and by means of human power the juice is squeezed out of them. Any hard material can act as a press (an old grindstone, a wooden circle hard rocks wood, metal product), the desired shape is round.

In the manufacture of this model, only the creation will take time screw press. To do this, you will need a so-called support frame, metal or wood, the screw itself, preferably with a handle for tightening, and a support board, the diameter of which must correspond to the dimensions of the inside of the container. If you have a welding machine and a metal sheet, then the screw mechanism described above, as well as a metal profile for attaching the support board, can be welded, which also does not take much time and effort.

You can use an old but working jack as a press, which is attached to the frame on top of the support board.

Among the homemade apple juicers automatic principle action, a popular option is to use elements that are old or out of order washing machine any type. What is needed to make it:

• take the drum of the machine, better known as a centrifuge, and an intact casing (tank);
• in the tank itself, it is imperative to close all unnecessary holes and holes in any way, leaving only one through which the finished juice will flow out during squeezing;
• if the filter mesh is preserved in satisfactory condition in the tank, then it can be moved and installed on the drain of the product;
• presence or self-production fastening units;
• ball bearings, if the old ones are ok, use them or buy new ones.

Please note that all materials removed from the washing machine must be thoroughly cleaned, removing washing powder, elements of rust, oils, scale.

Assembling an automatic juicer has its own nuances:

• engine installation DC power of at least 11 kW;
• making a frame for attaching the casing, it is best to weld it from metal corners;
• all electrical contacts must be well insulated, if possible use corrugation;
• before turning it on, you need to check that the device is assembled correctly; the electrical network must provide the required voltage;
• After assembling the device, it is necessary to rinse it thoroughly and perform the first idle start.

The product is ready for use. Do not forget that after each squeeze, the drum must be rinsed and cleaned. A product of this type shows great productivity: within half an hour you can process 2-3 buckets of apples and get natural fruit juice.

There is another simple option for creating a juicer to get your favorite apple drink. We take a regular mixer, attach 2 bolts to its bottom, connect it to electric drill and in a container (bucket, deep basin, tank) grind the apples. Place the resulting mushy liquid in a cloth bag and in a new container, preferably with holes in the bottom for juice to flow out.

Fruit preparation

Before squeezing the juice, the apples must be carefully sorted, since rotten fruits will subsequently negatively affect the taste of the future drink. After selection, the fruits must be thoroughly washed and the water allowed to drain. Large apples It is advisable to cut it into pieces; the core does not need to be removed, but in this case, after obtaining the juice, you will need to pass it through a thick filter to remove the seeds; the peel from the apples is also not removed.

After all the juice has drained, pass it through the filter. However, if you plan to prepare juice with pulp, and the cores of the fruits have been removed in advance, then the finished drink does not need to be passed through a filter. To save nutrients It is better to pasteurize the resulting juice, but not to boil it.

To learn how to make a juicer with your own hands, see the following video.

A high-performance DIY juicer is useful for gardeners who have to process large volumes of fruits and berries during harvest. IN living conditions Factory devices are used to meet the need for small portions of freshly squeezed drink.

Device types

Before you make a juicer with your own hands according to your own drawing, you need to study the principle of operation of the device. Depending on the design capabilities, squeezing processes can be carried out in compliance with a certain sequence of work stages or simultaneously.

Centrifugal juicers process the fruits into a pulp. They work according to a scheme in which, after grinding by a centrifuge, pressing occurs using a press. An auger juicer allows you to extract juice from fruits during processing.

Selection necessary elements designs are carried out depending on the type of device for squeezing juice. To simplify the processing process, fruits are crushed, for example, using a manual beet cutter. Complex designs involve the use of a mechanical drive for grinding.

Screw devices by design and appearance are close relatives of the home meat grinder. With their help, you can simultaneously grind and squeeze juice; they require more time to produce.

To prepare homemade fruit drinks, household appliances that can handle small volumes are often used. To process a bountiful harvest, the way out of the situation is a homemade juicer for apples and other fruits.

A simple old-fashioned method of extracting juice from fruits involves the stage of grinding and squeezing the liquid from the resulting mass. The apples, peeled from the core and spoiled parts, were poured into a wooden trough. By using special knife For grinding, the fruits were processed into a homogeneous mass.

The prepared pulp was packed in gauze and placed under a press in a wooden tub. To collect apple juice in a container, the design provided a hole in the bottom of the device to drain the liquid. The role of the press could be performed by heavy objects (stones).

The screw version of the press was equipped with:

• the frame on which the device is mounted;
• a screw with a fixed or removable handle;
• board for support, round shape, corresponding to the diameter of the inner part of the container.

How to create a high-capacity screw press for apples can be seen in the video. A do-it-yourself apple juicer is assembled from prepared parts.

To create the structure, you need to prepare 2 pipes, onto which a metal profile is fixed on top by welding. A hole is made in the upper part of the profile into which a threaded head is inserted.

At the bottom of the screw, the design provides a stop for squeezing. The rotation handle is fixed at the top, and clamps or a support structure for fastening are permanently welded at the bottom. The technical capabilities of the press depend on the volume of the tub into which the crushed raw materials are placed for pressing.

During operation, such a device is labor-intensive due to the execution of a significant part self made.

Hydraulic device

You can reduce labor costs for making juice using a design with a jack. To make it you will need:

• rolled metal (angle, channel);
• perforated basket;
• board;
• screws for fastening;
• short log.

The component parts of the frame are measured and welded into a structure. Holes are drilled in the pan.

Chopped apples are placed in a container. A wooden circle cut from a board is installed on top, equal to the diameter of the perforated basket. A piece of wood is placed on top. The hydraulic juicer is driven by a jack.

Automated design

A washing machine juicer is considered a popular option for extracting juice. The following parts are used to manufacture the device:

• centrifuge;
• ball bearings;
• fastening units.

All component structures must be cleaned of powder and scale residues before use. All holes in the tank are closed with rubber stoppers, leaving only one for draining the juice. It is useful to install a mesh above the drain outlet to filter the juice.

To grind fruits, a standard centrifuge requires additional modifications. The problem can be solved by using a steel lining, in which holes are drilled and teeth are filled.

A stack installed on the walls of the centrifuge can crush raw materials. Preparation of the working surface of the drum involves enlarging the standard holes and installing notches with the sharp part inward in the direction opposite to the rotation of the drum.

The completed grater is mounted in the tank using ball bearings and fasteners. The design is located in a vertical housing, the lid of which is closed with latches. IN top part The holes accommodate a hopper for receiving fruit.

When operating the device, the main thing is to ensure stability from vibration. It is recommended to secure the housing on a rigid base, and provide a limiter for the hopper. The engine of the device is borrowed from a washing machine. It can be mounted inside and outside the structure.

A screw device for squeezing juice is a more labor-intensive option. The main part of the parts is made individually. These include:

• frame;
• screw;
• juice tray;
• bunker;
• engine.

The structure is assembled and mounted on a stand made of a metal frame with an installed engine. The rotation of the auger is ensured by a belt drive from the engine to the pulley.

Grape processing

Before the advent of juice making devices, manual labor was used. Along with winemaking technology, from ancient times came the tradition of crushing grape fruits with one's feet.

At home, it is used for small harvest volumes. Special presses help process a significant amount of fruit.

There are presses various designs. They can be equipped with an automatic or mechanical drive, set in motion using a screw or jack. The devices work by loading grapes into a container that looks like a barrel.

Under the influence of a force that moves downward, the grapes are crushed. The resulting juice flows out through the holes.

A DIY grape crusher works on the same principle as a washing machine. Therefore, when making homemade structures for processing berries, parts of old machines are used.

If you don’t have an electric juicer, you can quickly and easily process a large apple harvest, for example, into juice using a press.

This problem also arises among winemakers, among whom there are no people willing to process the berries manually. It is quite possible to make a juice press yourself, eliminating additional expenses for purchasing equipment, which is quite expensive today. Operating principle of a juice press

Screw juicers manual type can be carried out according to different technologies, in this process, parts are used such as old containers, tanks from washing machines, as well as pots and boards.

In some cases, structures are made using a jack.

Homemade juice press

Simple press for squeezing juice - do it yourself

There are various juice press designs. Basic homemade designs– these are screw or using a jack. Not a bad option when using an air jack or rubber chamber and compressor. There are options for using a centrifuge, for example an old washing machine. Presses or juicers should not crush seeds and ridges located in the pulp. Depending on the expected volume of processing of raw materials into juice or wine, select the design of the juice extraction device you like. In any case, the cooking process is divided into two stages: 1. Preparation of pulp (grinding raw materials); 2. The actual extraction itself is the extraction of juice.

Screw Juice Press Designs

Typically a press consists of a pressing mechanism, a basket, a base and a pressing board. The basket serves as a receiver for the pulp and is installed on the base of the press. There is also a tray for draining juice. Bottom and side walls the baskets are lined with a whole piece of burlap without gaps. The ends of the fabric should hang over the edges of the basket. Then the pulp is loaded into the basket and covered with the ends of the burlap. A wooden circle is placed on top, onto which the press head is lowered.

Screw press with metal basket. Device: 1. Screw; 2. Bed; 3. Gutter for juice flow; 4. Basket

Screw press with wood basket. Device: 1. Screw; 2. Bed; 3. Basket; 4. Juice drainage chute

Frame screw press. Device: 1. Packages with crushed raw materials; 2. Screw; 3. Bed; 4 Drainage grates; 5. Juice drainage chute

Design screw juice press is clear from the pictures. Here is another example homemade press for juice. The press consists of two pipe stands with a diameter of 22 mm. A U-shaped profile bent from 3 mm steel is welded to the pipes on top. The height of the profile is chosen in such a way that a screw nut pressed into a steel sleeve can be freely placed inside. A clamp is welded to the bottom of each post. Using these two clamps, the press is attached to the window sill. A head with a hole for the handle is welded to the screw on one side, and a stop is attached to the other, which compresses the raw material.

1 - clamp; 2 - stand pipe; 3 - crossbar; 4 - screw; 5 - emphasis; 6 - table; 7 - bushing with a pressed nut.

A leaky 3-4 liter enamel pan is suitable for collecting the squeezed juice (Fig. a). You need to drill a hole in the bottom and attach a fitting with a hose to collect the juice.
The basket (Fig. b) is made of stainless steel sheet 2 mm thick; bandage rings made of stainless wire with a diameter of 4 mm are welded to it on top and bottom. The rings allow the basket to fit “evenly” inside the pan. The walls of the pan are perforated with a drill with a diameter of 3 mm (in random order).

Gaskets (Fig. c), which separate portions of raw materials loaded into the basket, consist of two 2-mm stainless steel disks connected by spot welding. Holes are drilled into the disks using a drill with a diameter of 3 mm, and gaskets 4 mm thick are provided between the disks (the gaskets are also made of stainless steel). In general, all parts of the screw press are made of stainless steel; a tank from an old washing machine is quite suitable. To obtain good harvest-, as well as growing strawberries at home. The work of squeezing juice occurs as follows. The body of the press is secured with clamps on the windowsill in the kitchen (you can also install the press on the table). The screw with the stop is unscrewed until it stops. A basket is placed in the pan, and a gasket is placed on the bottom of the latter and a napkin made of durable fabric is placed on it. Next, crushed raw materials (apples, fruits, herbs, berries) in an amount of 0.5...1 kg are placed on a napkin. The napkin is folded into an envelope, the portion is covered with a drainage pad, on which another napkin is placed. There should be 3 such bags, and the top bag can rise 4...6 cm above the pan. Putting a gasket on the top bag, the pan is placed under the press screw. Yes, I completely forgot to mention the spacer (a circle of wood) that is placed under the basket (otherwise the pan may become unusable when the screw is tightened). When creating pressure, the screw must be turned slowly and smoothly, monitoring the release of juice. Having finished squeezing the juice, unscrew the screw upward, transfer the pan to the table, and remove the pulp from the napkins. Depending on the type and quality of the raw material, in one cycle, using a homemade screw press for squeezing juice, it is possible to squeeze out 1.2...1.8 liters of juice, and in 1 hour - up to 12...15 liters.

Reading time ≈ 7 minutes

As an owner large garden, during the season you have to think about where to put the harvest. After all, it will not be possible to eat everything in a short time, and if the fruits are ripe, then they will not last long on the tree - they will begin to fall and spoil. However, there is a way out of the situation and it lies in homemade device. Let's look at how to make an apple press from a washing machine and improvised materials with your own hands. Using such a device from apples and other fruit crops You can squeeze out the juice, which will be much easier to process.

Advantages of a homemade juicer

If you have an old unused washing machine, automatic or activator, you can turn it into a useful device for extracting juice. The idea is to install a grater inside the machine. Through big hole The raw material is poured in, after which it is crushed and the juice is extracted. The advantage of this design is the ability to make juice in large volumes, which most household juicers cannot provide.

Moreover, in homemade device capacity for loading raw materials of a much larger volume. Equipping such a juicer with a powerful motor will allow you to get about 20 liters of juice per hour. This indicator is quite enough to process apples from your garden and also help your neighbor.

Juicer from an activator washing machine

To make such a juicer, you will need an Oka or Sibir machine. You can use other options equipped with a spin device and an activator at the bottom of the tank. Let's consider step by step production devices:

To ensure that the operation of a garden juicer made with your own hands from a washing machine is not limited by the relay time, the latter must simply be disconnected.

How to squeeze juice

The process of extracting juice is quite simple. To do this, you will need to wash apples or other fruits and load them in a small amount into the washing machine tub. The device turns on and the product is crushed using knives. The duration of processing depends on the specific apple variety and ripeness. After grinding, we obtain the mixture in the form of a puree and load it into a centrifuge in approximately 3 liters. Turn on the device and squeeze out the juice. After a few minutes, you can remove the mesh and shake out the cake.

What's so good about this juicer?

The main advantages of the considered design are as follows:

• productivity - about 12 liters per hour;
• apples and other fruits do not need to be peeled and cut;
• no need to constantly be near the device.

The presence of pulp in the juice will directly depend on the raw materials used and the duration of its grinding.

If you want to get pure juice, you just need to pass it through a filter, for example, thick fabric. You can also let the juice sit for a while.

Juicer from front washing machine

Making a juicer from a front washer is somewhat more complicated and will take more time. To construct the device you will need:

• belt-driven, front-loading machine;
• pair metal mesh size 300x60 mm;
• fasteners made of bolts and nuts with a diameter of 3 mm;
• juice container;
• rubber plugs;
• drain pipe;
• set of screwdrivers and socket wrenches;
• metal scissors;
• Bulgarian;
• electric drill;
• hammer and pliers.

Preparatory work

All unnecessary elements are removed from the washing machine (pump, sensors, filter, valve, control device), after which it is placed with its back side on the bars and fixed well. Then perform the following steps:

Manufacturing process

After preparatory activities All that remains is to do the following:

1. The mesh is fixed inside the drum using screws. It can be easily dismantled for cleaning.
2. In order for the raw materials to be crushed, the ribs need to be sharpened.
3. A pipe is attached to the drain hole.
4. Mount the electric motor.

How the juicer works

Before you launch assembled structure, you need to make sure that it is stable, as well as that the drum rotates evenly without jamming. After this, the fruits are washed and loaded inside the machine.

There is no need to fill the device to the top with fruit. Otherwise, the machine will not grind and may break.

If loading hard apples, the drum should be half full. Soft raw materials can be placed in larger quantities. Place a bucket or pan for juice under the drain pipe. All that remains is to start the motor in spin mode. As the drum rotates, the apples will beat and juice will flow out of the resulting mixture. As with the previous design, there is no need to cut the raw material into pieces. The performance of such a juicer is approximately the same as in the version described above.

Washing machine drum press

From a washing machine you can make not only a juicer, but also a press, using separate parts from it. The design is quite simple since there is no electric motor, no electricity required, and no complex structural elements. For the washing machine, we only need a centrifuge made of stainless steel. Since the part has holes, this allows it to be used for the purposes in question. The manufacturing process consists of the following steps: