It will be useful for any owner to know how to disassemble the handle on the door, especially the interior one. This fitting is subjected to a serious test by all tenants, so someday it will fail, and it will need to be replaced with another one. In this case, you do not need to call specialists, you can handle it yourself, while saving on the employee's wages. Moreover, this business does not require great skill, but only a little skill. The dismantling process may differ depending on the type of handle, but the whole process should not cause any particular difficulties.

How to remove the handle from interior door? Before proceeding with the analysis of the mechanism, you need to find out what kind of classification it belongs to. The division is based on several criteria. The one described below is suitable specifically for parsing a pen, because it has a classification according to design features.

Varieties of handles

Press. Such a handle is attached on both sides of the door leaf and has an L-shape. Opening occurs due to the load on the handle, after which the tongue is set in motion. The disadvantage of this fitting is that it is very traumatic.

Swivel. The opening method is the same as that of the push, only the tongue is set in motion not by pressing the handle, but by turning it. Such models are often not very convenient, because to scroll it, you need to have your hands dry, otherwise they will slip. When replacing them, a reasonable question arises about how to unscrew the interior door handle.

Stationary. This handle does not have a latch. It is attached with screws directly to the door leaf. It happens one- or two-sided, while it has an axial connecting element.

Reasons for parsing a pen

It is not so difficult to disassemble any of the models of door handles, because they have a similar design.

At the same time, it is extremely rare to carry out the analysis of this fitting. What reasons can lead to this? How to remove the handle from the interior door?

The first reason is breakdown. It occurs most frequently. Often, inexpensive Chinese models are prone to breakdowns, which are not designed for a constant and rough load. If the prevention of some elements is not observed, then the fittings become unusable. It should be repaired, and sometimes the entire element should be replaced.

The next reason is the need for replacement. Every year the market is replenished with new and improved models. At the same time, you can choose color scheme suitable for the interior, or put a new, more functional and reliable model.

Renovation in a room often involves a change in style. Do not ignore the door handles. Therefore, the question often arises of how to disassemble door handle.

Another reason is spoiled appearance. If the part is made of low-quality material, then scuffs and scratches will be visible on it very soon, which negatively affects the entire interior.

Removing the push handle

How to remove the handle from an interior push-type door? This mechanism is more difficult to disassemble, because in its design there is an axis rod, due to which the handle is held. It is tightened with a tetrahedron.

The process of parsing the handle must begin with the removal of the plugs around it. They are fastened with screws or tightly pressed. They are very easy to remove with a minus screwdriver.

On one side of the door, you need to unscrew the fittings and remove. Then the second part is removed, on which the axis rod remains.

If the handle is with then it is also removed.

Following the sequence and accuracy will allow you to remove the mechanism without problems, without damaging the parts and without creating unnecessary hassle.

How to remove the handle from the interior door rotary with a rosette?

When there is no hole on the side of the rotary type fittings into which a key or screwdriver can be inserted, the elements are separated manually. Both parts of the handle should be scrolled in different directions and gradually removed from the thread. On one of them there will be an axial rod.

In this way, the socket is removed and the screws are unscrewed. When the axis is removed, you can do the following elements - a latch or lock, if necessary. When decorative parts are removed, you need to monitor the use of your strength, because overdoing it can damage the elements.

Removing the rotary knob

The handle with a lock for interior doors of a rotary type is removed as follows.

This will require a key to clamp the spring mechanism. Often it is not included in the package with the product, but it can easily be replaced by a nail or other thin object.

The first step is to remove the decorative plates, which can simply be pry off with a sharp object.

Use a key or nail to move the spring-loaded pin by inserting the tool into the technological hole located on the side. At the same time, pull the handle and remove it together with the cap.

After that, you need to move the fastening screws located on the plate. Then the two parts of the handle can be removed together with the axle.

Assembling the round door handles back is not difficult, only all steps must be done in reverse order. First comes which is fixed with a plate, then an axis is inserted, fasteners are put on it. Decorative inserts are mounted last. The main thing is not to forget that the decorative flange is first threaded, and only then the main part of the handle is attached.

Removing the fixed handle

How to disassemble a fixed type door handle? They are the least likely to break or deform. This is due to the lack of moving elements in it. Often doorknobs of this type after removal, they do not repair, but change entirely. The withdrawal process is as follows:

1. Self-tapping screws are unscrewed with a screwdriver.
2. One part is unscrewed from the rod, and the second is removed along with it.

This design may not have a central rod, which greatly reduces the process. You only need to choose the right screwdriver to unscrew the screws of a certain diameter.

Removing the latch handle

First of all, when dismantling the latch handle for interior doors with an automatic lock, you need to remove the screws with a screwdriver. Next, unfasten the overlays. Use to unscrew the rod.

After that, pull out the rotary mechanism wrapped in a spring.

popular way

There are several ways in which the latch handle for interior doors is removed. round shape with latch. Here is the most popular one.

It is necessary to remove it with a screwdriver, first from the part where the latch device is located. It is necessary to press on the opened stopper and at the same time pull the handle towards you.

Then the latch is pulled out, for which the screws are unscrewed, after which the latch is released.

Thus, disassembling any door handle with your own hands is not a big problem.

The door handle is used several times a day, resulting in the need to repair the device or complete replacement. The first stage of the work is the analysis of the handle and finding out the causes of the breakdown. How to disassemble the interior door handle yourself, read on.

The main types of handles for interior doors

The following types of handles can be installed on the interior door:

• stationary. The handle does not have any latch elements and serves solely to cover or open the door. Stationary handles can be installed on one or both sides of the door;

• pressure. When the door handle is pressed, the latch mechanism retracts into the interior of the handle, making it possible to open. If the handle is in the horizontal direction, the door is closed and fixed in the selected position;

• rotary. The latch-lock is actuated by turning the handle. Rotary handles for maximum user convenience are made in round shape as a priority. Round knobs are also called knob knobs.

The push and turn handles can optionally be fitted with key operated locks.

Handle disassembly

When Disassembly is Necessary

Self-disassembly of the handle may be required:

• when a creak is formed or the latch mechanism is jammed. In this situation, it is enough to lubricate all working elements. For lubrication, machine oil or a special mixture of WD-40 is used;
• when the device is not working due to a long period of use or lack of care and periodic maintenance. All door handles require regular inspection and timely lubrication of moving elements, which increases the life of the product;
• to carry out the current, for example, to replace the latch or tighten the mounting bolts that fix the device on the door leaf;
• to replace the handle with a newer or improved model. New models are constantly appearing on sale that can serve as an interior item or have a greater degree of protection.

How to disassemble the interior handle for repair or replacement? For this, you need to familiarize yourself with the following instructions, which are developed by experts for the most popular types of pens.

Replacement of stationary handles

To replace the stationary handle, it is necessary to unscrew the fixing screws, which can be located:

• on the front of the handle;
• under a decorative overlay.

To remove the decorative trim, it is enough to carefully pick it up from one side with a sharp tool.

Disassembly of rotary knobs

To disassemble the round handle, you need to prepare:

• special wrench for loosening the locking pin. The key is supplied with the handle. If a special device is lost, then you can use any hex key that is suitable in diameter;
• screwdriver.

The disassembly of the handle is as follows:

1. on the decorative overlay, you need to find a hole for the hex key. It is most often located below or on the side;
2. the key is inserted into the hole and pressed lightly. In this way, the locking pin is loosened;
3. the other hand removes the handle. To do this, just pull the device towards you;

1. at the next stage, a decorative overlay is removed that covers the hole in the door leaf;
2. under the trim there are fixing bolts that must be loosened with a screwdriver. After performing this operation, the door handle splits into two parts.

If you need to replace the rotary knob, you will also need to remove the latch. To do this, it is enough to unscrew the fixing screws located on the end part and fixing the corresponding mechanism.

Removing the latch mechanism

The process of self-disassembly of the rotary knob is presented in the video.

Lever handle disassembly

To disassemble the handle with a push mechanism, you will need a screwdriver that is most suitable for the mounting bolts.

The disassembly process is carried out as follows:

1. the first step is to remove the decorative trim. The lining can be attached in two ways:
   • using carving. To remove the element, turn the cover several times counterclockwise;
   • with the help of a latch. To remove the overlay, you will need to move the tongue a little to any side with a sharp tool;

If, due to contamination or breakage, the lining does not turn away, then you can resort to using a screwdriver and a hammer. The screwdriver is inserted between the trim and the door. Hammer blows on the screwdriver handle allow you to move the mechanism from its place and unscrew it completely.

1. the next step is to unscrew the bolt located at the bottom of the handle. With the help of this fastener, the handle itself is fixed to the mechanism with a latch;
2. under the decorative trim there are two or three screws that fix the main mechanism;

1. after unscrewing all fasteners, the handle is freely pulled out.

The locking mechanism of the lever handle is removed in the same way as handles with a rotary system.

Having become acquainted with the proposed schemes for disassembling door handles, it is possible to repair the device or replace it without the help of a specialist. To install the handle, you can follow the instructions attached to the new device or perform all the steps indicated in the diagrams in reverse order.

Do-it-yourself installation of a lock with a latch on the door is within the power of almost every man who knows how to use a tool. In this article, we will tell you how to mount and disassemble a door handle with an integrated latch yourself. In addition to textual information, the material is provided with a video that will help you better understand the work process.

How to disassemble the latch handle and dismantle the lock

Door handles with latches are convenient in everyday life, they are installed on the entrance and interior canvases. The mechanism can be push (classic L-shaped version) or rotary (in the form of a ball or socket).

To disassemble the push-type locking mechanism, you must first remove the handle. On the side or bottom on it, you need to find a recessed screw and unscrew it with a screwdriver (in some cases you will need a hex key). Then the decorative overlay is removed. Most often it has a thread, and this is easy to do. Having removed the panel that hides the fasteners, you can unscrew the main bolts holding the mechanism. Next, the lock plate is unscrewed from the end side of the canvas. The lock can be easily removed by pulling it towards you.

The process of disassembling a device with a rotary round handle differs little from actions with a push mechanism. In some models, the ball is threaded, you only need to hold the second handle motionless, turning the part to be removed in the opposite direction. Sometimes manufacturers supply mechanisms with screws hidden in small recesses, as in pressure devices.

In some models it is necessary to find on the handle small hole. Having found it, we turn the ball so that in this recess we see a button (stupor). By pressing on it with something thin, we pull the handle towards ourselves. Often the kit comes with a special key for this. Decorative protection in such models is usually removed if you simply pry it off with a knife or screwdriver.

Installing a Latched Door Handle

Installation is divided into several mandatory stages:

1. Determining the installation location and marking.
2. Drilling holes.
3. Mechanism fastening.
4. Box preparation.

Having determined the height of the location, mark the center of the handle. Next, the place for the latch is marked. To do this, determine the middle of the end of the door, apply the lock as it will be mounted, outline the tongue. To work, you need to prepare the following tools:

• Drill;
• Screwdriver;
• Chisel;
• Hammer;
• crown on wood;
• Feather drill;
• Spiral guide drill for wood;
• Square;
• Line, roulette.

To drill a hole for the mechanism, a wood crown is used. First, one side of the canvas is drilled, then the other. If you immediately make a through hole, then decorative coating on the opposite side may peel off. The drill must be held at an angle of 90° during operation.

Important! For most standard models locks with latches, a feather drill with a diameter of 22-23 mm and a 50 mm wood crown will do.

The hole for the tongue is most convenient to drill pen drill with guide. The speed of the drill should be minimal, you need to work carefully. A mechanism is inserted into the resulting hole and the location of the plate is marked. In order for the lock to be located on the same plane as the end of the door, excess wood is chosen with a chisel.

The mechanism is installed in place, the plate is screwed under the latch. A square is inserted, the design of the handles is assembled, everything is tightened with screws. The last step is screwing decorative panel that hides the fasteners and firmly tightens the locking screw.

Advice. In order to screw parts of the lock with a latch without distortions, the screwing points are first marked with an awl, then drilled with a thin drill. In this case, the screws go into place easily and correctly.

To mount the reciprocal hole in the box, after closing the door, leave a small mark from the latch on the jamb. You can smear the tongue with oil for this. Having outlined the place, we apply the overlay that comes with the lock, circle it along the contour. We drill a hole for the tongue, deepen the bar, then fasten it.

Installing a door handle with a latch with your own hands is not difficult, if you take your time and do everything carefully. Almost every model has an instruction, it will not be superfluous to familiarize yourself with it first. By following our advice and manufacturers' recommendations, any House master will do a great job.

How to disassemble the door handle knob: video

Door handle with built-in latch: photo

Nowadays, almost any interior door is equipped with such a thing as a door handle. Moreover, we are not talking about an ordinary handle, for example, a round one, which you can simply grab, but a mechanism that allows you to open and close the door and, if necessary, keep it in the closed position, despite the efforts made to open it. Such a mechanism is, for example, a latch with a latch. As you use door furniture wears out, and any handle just breaks.

Today we will talk about how to disassemble and dismantle it.

Features of various designs

First, let's talk about the designs of door handles and their features.

• The first category we will look at is stationary models. These are the most common solutions for interior doors. Such fittings are now practically not used. Is that on the doors installed back in time Soviet Union which have not been upgraded since. And in residential premises it is usually not used. Outwardly, it looks like a bracket. There are two varieties of this model. The difference between them is that they can be one-sided or end-to-end.

If we talk about the latter, then on long screws, 2 handles are fixed, which are placed with different parties door leafs - one against the other.

Such a handle is removed very easily - just unscrew the bolts that hold this design. Such fittings can literally be called a penny, as it has a minimum price. Yes, and repairing it is pointless, because she does not understand.

• The next option is pressure structure. Such a decision on the structure will be a little more complicated. The handle is a lever-type product: the working elements, thanks to the axis, are tied to the lock mechanism. Some options of this type are additionally equipped with a latch that locks the obturator.

Such a handle can be dismantled using a screwdriver with a narrow sting. By the way, such a handle can have a lock with a metal core.

• Another design worth mentioning is rotary model. It has a lot of differences from the above options, which are in the form and design features. The general principle of operation is the same as that of other models.
• The next version of the considered fixtures for the interior door is handle with socket. Such handles have a round shape and, depending on the design, can be disassembled according to different algorithms. They also differ in the method of fixing the decorative element. The spherical shape is very convenient to use. Such models are also called knobs.

In general, as can be seen, there is a large number of door handles for interior doors. Each type has its own advantages and disadvantages, at the same time, the algorithm for disassembling them will be approximately the same.

Required Tools

To disassemble the door handle, you will need to have a certain tool on hand. Regardless of its type, it may contain some hidden elements and parts that cannot always be pulled out using conventional tools.

For this reason, the following list of tools should be on hand:

• hammer;
• screwdriver;
• drill and set of drills with a crown;
• pencil;
• awl;
• square.

How to disassemble and remove?

Dismantling the door handle is quite simple with the above tools, as well as a little knowledge of the theoretical plan for the structure of this mechanism.

To do this, you must follow these steps.

• Support and fix the door well so that it is in a fixed position.
• Now you need to pry off the decorative type flange and pull it off a little. Under it are fasteners that should be unscrewed.
• On the mentioned flange of the pressure part there is a special pin, which is locking and spring-loaded. It should be pressed in with a screwdriver. In rotary versions, it is usually located in the housing. To get there, you should insert a key or an awl. If it was not possible to probe it, then the flange should be rotated until it comes into contact with the pin.

• Now you should press the pin and at the same time pull the handle design.
• Now we unscrew the fastener bolts.
• We separate the inner part of the element from the outer one, pull out the handle and the decorative type flange.
• If there is a need to remove the latch for replacement or repair, then unscrew the screws that fix it on the side of the door block, then remove the bar, and then the mechanism itself.

When mounting accessories to a different position, it is better not to disassemble it for spare parts. It attaches easily to door structure, but in reverse order.

Now let's talk directly about the disassembly of each category of pens.

• Let's start with the stationary, which does not have a push fitting, and is also not equipped with a mortise-type lock. In order to unscrew such a handle, you will need a Phillips or flat screwdriver. Alternatively, you can use a screwdriver. Dismantling must begin by loosening the screws that secure the mechanism.

If there is decorative elements, they must first be removed. As the bolts are loosened, counter parts should be held with reverse side canvases. If this is not done, then the structure may simply fall out of the canvas and deform.

It should be noted that the fastening can be one- or two-sided, respectively, the design can be disassembled in different ways, which means that this must be taken care of in advance. When all the bolts are unscrewed, it is necessary to carefully remove the handle from the door leaf using a flat-tip screwdriver. into place old pen a different mechanism is installed or the same design, but with new spare parts.

• If you lead we are talking about disassembling a round handle with a socket, it is necessary to clarify that the word "socket" is usually understood as a mechanism that allows the lock to be locked using a small key on one side, which is not used on the other side. On the second side there is a special lamb. In this situation, the disassembly of the mechanism will be carried out according to the following algorithm:
  1. first, the screws that hold the trims that perform a decorative function are loosened on both sides;
  2. the screws connecting the mechanism on both sides are unscrewed;
  3. the handle design is pulled out and the rest of it is removed;
  4. the lock mechanism is pulled out.

If the handle needs to be repaired or any part of it needs to be replaced, then it should be completely disassembled after that. individual elements and determine the cause of the problem. It is necessary to carefully monitor the safety of all small structural elements, otherwise, if they are lost, it simply will not work to assemble the mechanism back.

• Now let's talk about disassembling a round knob-knob. To dismantle this element from the door leaf, the following steps are usually performed.
  1. The fastening bolts on one side of the door are unscrewed.
  2. The mechanism is dismantled through special holes.
  3. Disassembly of an additional counter-type bar is being carried out. To dismantle this element, simply pull it in your direction.

The non-separable round handle is fixed using the simplest screws for fasteners. This mechanism is made with the expectation that later no repair work will be carried out, but a new spare part will simply be purchased, which will take the place of the old handle.

• Push options. Usually, instead of turning solutions, they are used. This is due to the fact that they are durable and very easy to use and repair. Disassembly is performed as follows:
  1. first, the screws holding the decorative canvas of the overhead type, which performs the function of a clamp, are unscrewed;
  2. after this, the overhead canvases located on both sides are carefully removed;
  3. fastener bolts are unscrewed and round structural elements located on both sides of the door leaf are pulled out;
  4. it remains only to open the striker and the lock itself, and then pull them out of the fitting grooves.

How to fix?

Often, door handle repairs are carried out in the following situations:

• the handle sticks and is difficult to turn;
• the handle does not return to its normal position after being pressed;
• the handle falls out, and the base is not damaged;
• the tongue does not move when pressed.

In this material, we will consider with you how to disassemble the knob knob, which have received an unusual distribution on interior doors. And also along the way we learn how these handles are installed. Below you can find not only instructions in pictures, but also watch a video.

To install the handle-knob, it is necessary to mark on the door and make two main holes, according to the template, which, as a rule, is included with the handle with installation instructions. So, let's start installing the handle, disassembling it along the way.

Given interior door:

We make a sample hole from the end of the door leaf under the latch. Hole diameter from 23 to 25 mm: It is convenient to make a hole with a so-called spade drill for wood.

With a crown on a tree with a diameter of 50 mm, a through hole is made for the main fastening of the handle. The distance from the end of the leaf to the center of the hole is 60 or 70 mm, depending on the latch that is included in the kit.

You can find a template for installing a knob-knob from some manufacturers in the form of a stencil on inside packaging-box or in the attached instructions. It is very convenient to use ready-made kits for installation, which are called “installation kit interior handles". It is not scary (and often, on the contrary, it is useful) if the holes are made with a diameter of 1-2 mm larger than recommended. Two-position latch mechanism: provides for the possibility of installing a knob on the door, with different width the first bar of the door. The removal of the center of the handle-knob from the edge of the door leaf in the standard is 60mm:

but by moving the sleeve under the square, you can set the distance to 70 mm:

The standard height of the handle on the door is approximately 950 mm from the floor level. Next, to install the knob-knob, we partially disassemble the inner half of the handle in order to gain access to the holes for the mounting tie-down screws. To do this, we use a special “key” from the handle kit or any suitable item, for example, a knitting needle. There is a special hole on the handle, through which the door knob should be disassembled. In the photo shown it is round, but it may be various shapes. This hole is located at the bottom of the handle:

Through the hole we press the spring-loaded latch, while pulling out the handle of the interior knob.

We take out the handle and completely remove it:

Then you need to pry off the outer decorative flange of the handle with any sharp object. Take a closer look, as a rule, the flange has a corresponding groove for this:

well, the knob-knob is disassembled and we got access to the mounting screws

Further assembly of the handle-knob occurs on the door in the reverse order.
First, install the latch in the door and secure with two screws from the end. It will look like this:

Rectangular latch mechanism faceplate, flush mounted with door leaf. To do this, marking under it, with a chisel, the required depth is selected at the end of the door leaf. The same applies to the striker of the knob, which is installed according to the markup, on door frame. Also, under it, the required depth is sampled with a chisel.

Further, it is already possible to assemble the knob-knob on the door leaf, pulling together the disassembled halves with fixing screws. The square of the handle and bushings for the mounting screws will, during installation, pass through the previously installed latch, through its technological holes

Handles-knobs are universal and are not divided into left / right-handed. The design provides for the installation and adjustment of the knob for any door with a thickness of at least 35mm.

If the shape of the knob-knob has an asymmetrical shape of a ball, etc., then after installing the knob on the door, using the method described above, remove the knob handle, and change the outer and inner handles in places, having achieved their correct location, relative to the location of the door leaf ( left or right side). The mechanism of the latch or lock, if any, is also given in correct location, and if required, also swap the outer and outer sides.

The handle, assembled and without distortions, installed on the door, should work easily in both directions and independently, under the action of a return spring, return to its original position. If this does not happen, then you need to check the evenness of the installation, as well as tighten or loosen the fixing screws, achieving their equal tightening and soft stroke of the knob.