Wall decoration with wallpaper is the most popular option for decorating indoor walls. Undoubtedly, gluing wallpaper on flat walls is quite elementary and requires only a little skill, but wallpapering the corners of a room is technically more difficult. Before you apply wallpaper with your own hands, you need to properly prepare the walls.

First you need to remove old wallpaper or paint, apply primer to the walls and level their surface. And only then start wallpapering the corners.

So, repair specialists identify the following stages of this process:

1. You need to start by leveling the corners; for this you can use putty and after it dries, clean it sandpaper. In order for the angle to be even, you can use special device– a plastic corner that is attached to the putty. Remember that if you don't get rid of uneven surfaces Wallpaper may come off.
2. The next step is to apply glue - before gluing the wallpaper to the corner of the room, you must very carefully coat the entire height of the corner with glue. If the roller does not cope with its task and leaves uncoated parts, you should use a brush.
3. Directly pasting corners with wallpaper - there are various lessons from specialists that help to correctly wallpaper a corner of a room, it’s worth listening to them, but for greater productivity let’s outline some features of this stage: competent finishers do not recommend gluing wallpaper in whole strips in the corners, this is explained by the fact that they can distortions will appear and the joints will be uneven.
4. The wallpaper must be cut so that its side extends 50 mm onto the adjacent wall.

The glue must be applied to the strip of wallpaper and the corner of the wall. Next, you need to apply the wallpaper to the corner of the wall as follows - if the pasting process begins from left to right, then the left side is applied to inside corner for even coverage.

At this stage, you need to clearly understand that you need to wallpaper the outer and inner corners in different ways.

Outside corner

External corners can be glued in two ways: firstly, if outside corner has flat surface, you can not waste time on leveling it and immediately apply wallpaper to the corner, then use a level and measure the edge of the strip so that the remaining strips lie evenly; secondly, to paste the outer corners, you first need to bring the strip around the corner 4-5 cm, and glue the next part of the wallpaper at the top. By using stationery knife and a ruler to cut these layers vertically.

Internal corner

Internal corners require more attention. Wallpaper should be glued so that it extends onto the adjacent surface by about 3 cm, but no more, otherwise it will wrinkle. The bend and rotation of the wallpaper must be coated with glue. Next, you need to measure the width of the wallpaper located on the adjacent wall, mark the allowance of the pasted side, which is glued at a distance of approximately 2 cm from the corner and a vertical line is drawn through it using a plumb line - this will be the mark of the edge of the wallpaper to be pasted.

Wallpaper is leveled using the rolling method; there are special rollers and spatulas for this.

All the above stages of wallpapering in the corners proceed sequentially.

Wall corners for wallpaper: what is it?

Plastic corners Wallpaper is a good finish for finishing corners - they have protective functions and give the corner a finished look.

Construction markets offer various decorative corners:

• Corners with a width from 20×20 to 50×50 mm are suitable for corners that are subject to heavy wear;
• Dimensions of 10x10 or 15x15 mm will give a neat, finished look to the wall - they are called decorative corners;
• The corners may differ in color and may have the texture of wood or metal.

For arched external corners, it is better to use corners with the following approximate dimensions: 5 × 17.7 × 17.10 × 20 and 15 × 25 mm. It is recommended to install plastic corners using silicone sealant, it is colorless and has good adhesion. The length of the corners ranges from 3 to 7 m, so it can be adjusted to individual sizes.

Decorative plastic corners help protect wallpaper from mechanical damage at the corners of the wall; in addition, they are not expensive and easy to install.

How to glue wallpaper in non-woven corners: features and tips

Non-woven wallpaper is particularly durable, but it is quite difficult to work with it, especially on corner surfaces, because they are not elastic.

To cover a corner of a wall with such wallpaper, when cutting off part of the wallpaper, you need to make an allowance of 1.5 cm, this allowance should overlap.

Need to know little secret– gluing non-woven wallpaper will be easier if you make equal cuts along its edge along the entire length.

In this case, the glue is applied only to the wall, and the wallpaper should remain dry. When decorating a corner with such wallpaper, it is better to use a corner first, then unnecessary crooked places will not appear. If the choice is made in favor of wallpaper with a pattern, in this case it is necessary to carefully adjust the pattern in the corners. In order to keep the pattern in the corners intact, you need to cut the next strip from the corner to match the pattern of the already pasted wall.

Here are some tips:

• It is necessary to make a small overlap on the other wall;
• It is better to hide the joints at the top of the corner;
• It is better to glue wallpaper with a pattern in the corners plumb.

Meter wallpaper is a wide non-woven fabric slightly larger than a meter. This type of wallpaper helps to paste over faster large apartment and choosing a pattern becomes easier. In order to paste meter-long wallpaper in the corners, you need to overlap up to 3 cm on next wall. The rest of the procedure will not differ from the standard pasting of corners, which is described above.

How to glue corners to wallpaper: installation technique

Then proceed according to the following plan:

1. The adhesion of the corners to the wall will be stronger if they are glued to the wall rather than to the wallpaper;
2. Evenly distribute the adhesive material along the inside of the corner;
3. Attach and press to the desired area on the wall, remove excess glue with a napkin;
4. Do not touch the corners until the material is completely dry.
5. In order for the sealant to adhere better to the area, you can secure the corner with adhesive tape.

How to properly glue wallpaper in corners (video)

So, knowing the technology for gluing wallpaper in corners, you can high-quality repairs with your own hands and also help your family in this difficult matter.

If all surfaces were perfectly smooth, it would be so simple and easy to stick wallpaper to the wall! However, things are not so simple when it comes to wallpapering corners. Every little detail is important in this matter. In this article you can get invaluable information on how to glue external and internal corners, and you can confirm your book knowledge by watching the video lessons we have prepared.

Even a beginner can stick wallpaper on a wall. With the right adhesive that matches the type of wallpaper, you can easily cope with flat wall, devoid of various bends and angles. However, many people have difficulty with the corners of the rooms, and this is where all sorts of difficulties associated with the task begin. There are so many experts, so many opinions, on the question of how to glue wallpaper in corners.

How to properly glue the inner and outer corners of a room

Internal: Each standard room has at least four corners. From what angle should you stick the wallpaper? If you are new to the world of renovation, in particular wallpapering, then start from the corner that is not in the most visible place. We recommend that you practice in inconspicuous places in your home.

In order to achieve perfect result, then you need to glue the wallpaper in the corners so that the wallpaper glued to the wall extends onto the adjacent surface by no less than 3 cm, otherwise there is a possibility of the wallpaper peeling off in the room after drying, and no more than 5 cm, otherwise the adjacent the strip will wrinkle.

Folding and turning the wallpaper onto an adjacent plane must be carefully lubricated with glue, pressing the canvas firmly for a more reliable fixation. The further algorithm of actions is simple: you must measure the width of the adjacent canvas located on the adjacent wall. As a rule, it is about 53 cm. The mark for the allowance of the glued strip of wallpaper should be fixed at a distance of approximately 2 cm from the corner, draw a vertical line through it using a plumb line. This mark will be the edge of the glued canvas.

External: If your room has external corners - be it all kinds of niches, protrusions in the walls - then information on how to wallpaper external corners will come in very handy. There are two gluing methods:

The process of wallpapering with trimming in the corner of the room video tutorials

1. Making sure that the outer corner has a perfectly even texture and does not require additional leveling or putty. First you need to apply wallpaper to this place. Using a level, it is necessary to measure the edge of the strip so that subsequent sheets can be glued evenly.
2. By analogy, the internal and external corners of the room must be glued with wallpaper as follows: first, the strip should be placed around the corner by 4-5 cm, and the next strip should be glued on top with an overlap. Using a paper knife and a ruler (preferably an iron one - it is stiffer and will not move to the side) we make a vertical cut between two layers of material.

How to properly glue corners with vinyl wallpaper

Vinyl sheets are very attractive, however, to glue them, you should learn about characteristic features this type of material.

Secondly, when gluing, you should not bend the entire panel at the junction of the walls. In order to properly glue wallpaper in corners, vinyl wallpaper experts advise not to bend the entire panel for pasting at the junction of the walls.

A characteristic feature of vinyl is that it is undesirable to combine two solid panels in one corner. The best option This is done by gluing a continuous strip with an overlap of 3-5 centimeters.

How to paste the corners of a room with non-woven wallpaper

How to glue wallpaper in the corners if your choice fell on a material such as non-woven fabric? To properly paste over an internal corner in a room, you need to cut the fabric that goes over it with an allowance of 1-1.5 cm, which should overlap the adjacent wall. They will fit more tightly if you make small cuts along the edge along the entire length and at an equal distance every 4-5 cm, and press the canvas tightly against the wall.

You can start gluing the adjacent wall from the opposite corner, and when all the strips are pasted, the last strip needs to be cut with an overlap of 2-3 mm, gluing it overlapping.

Subtleties when gluing wallpaper video lessons

The peculiarity of how to glue outer corners is that the strip of wallpaper adjacent to it must be cut so that the distance between the seam and the corner is approximately 1.5-2 cm, which will need to be rolled around the corner. Along the edges, as in pasting the inner corners, make cuts, and the next strip of wallpaper should be glued on top, overlapping the edge on the corner.

If you do, then both strips should be cut at the corner using a sharp knife, and after gluing, you need to walk along the joints in the corner part, and only then paint.

Angles and drawing

The easiest way is with wallpaper without a pattern. However, how to glue wallpaper in the corners of a room with a selection of patterns if your choice fell on canvases with a pattern? It is important to think through everything in advance before purchasing wallpaper. You should take into account such an important factor as the unevenness of the walls in the room, as it can have a significant impact on the final result. The simplest material is with a vertical pattern, however, if you have uneven walls, this will only emphasize the curvature of the walls. It is not advisable to give preference to canvases with patterns - large and small flowers, as well as complex patterns.

How to wallpaper in corners with a pattern? Do not rush to haphazardly cut the wallpaper into strips of the required height. Take the time to match all the patterns before you start trimming. To maintain the integrity of the pattern, the strip next to the corner needs to be adjusted, trimmed to match the pattern of the finished wall.

You can get a more visual idea by watching the video on our website. They will help you understand all the intricacies of wall repair and wallpapering corners, both external and internal.

How to trim an inside corner video tutorials

A certain logical completeness of your renovation will depend on how carefully you arrange the corners of the room. Follow the advice given in this article, and you will never have problems when gluing vinyl and non-woven wallpaper, and the thought of how to properly glue wallpaper in the corners will not take you by surprise.

Reading time ≈ 8 minutes

- the most common type decorative finishing walls The technology of the process does not seem complicated from the outside, because even a beginner can apply glue to the wallpaper and stick it to the wall. Therefore, many owners decide to do this work themselves.

A beginner can easily handle wallpapering if the wall surface is fairly smooth and without obvious defects. However, the surface is not always properly prepared and leveled for finishing works. And also, amateurs often face the question of how to properly glue wallpaper in the corners. Here it is important to ensure that the selected pattern matches, if present. Therefore, in this article we will talk about a special technique for gluing wallpaper in corners.

Material selection

Wallpaper remains the most popular material for decorating walls in an apartment or office premises. They are able to transform a room beyond recognition, hide interior imperfections and highlight advantages. What you need to know when choosing wallpaper for your apartment:

In the store, modern wallpaper is presented in a wide range of models, varying in texture, color scheme and composition. Most rare species– liquid wallpaper sold in the form ready solution V plastic buckets. However, we will consider the more common roll type. There are several types of wall coverings, the most popular of which are:

Each profession has its own tricks, if followed, you can achieve the fastest and highest quality results. Pasting wallpaper in the corners is a labor-intensive process that requires compliance with some nuances:

• The corners in the room should ideally be straight and located strictly in a vertical line. However, often rooms do not have the correct geometric parameters, so the corners must be aligned.
  
• For curved corners and walls, it is better to choose voluminous canvases made of vinyl or non-woven fabric. The pattern should be simple and the shade should be matte. You need to glue such wallpaper in the corners of the room to mask all the imperfections.
  
• If you have uneven corners, thin paper sheets, or 3D coatings with large intricate patterns that need to be adjusted all the time, are not suitable for you.
  
• It is best to start gluing from the window, gluing the very first sheet strictly vertically.
• If your room has smooth corners, it will be enough for you to treat them with putty, masking minor minor irregularities.
  
• The corners should be aligned using special plastic corners, which are easy to find in any hardware store. They are securely attached to the wall using putty.
  
• The corners need to be leveled at the stage of finishing puttying the walls.
  
• If you decide to glue paper sheets without using an additional layer, you should take into account the capriciousness of this material. Gluing must be done promptly so that the paper does not have time to absorb moisture from the glue.
  
• If there are sockets or switches in the gluing area, you should turn off the electricity in the apartment during the work. This way you will avoid unpleasant situations and undesirable consequences.
  
• Do not cover the corners with solid canvas. Before starting work, you need to take accurate measurements and cut the wallpaper into strips so that one sheet extends at least 20 centimeters onto the next surface. For example, gluing non-woven wallpaper even in even corners with a solid sheet is quite difficult.
  
• Don’t forget to coat all walls and corners with glue before you start gluing. The glue must be distributed over the entire surface, and in the corners with special care. It is believed that it is in the corners that wallpaper most often begins to peel off and come off. Using a roller, the glue can be easily distributed over the entire area and perfectly prepare the surface for further finishing.
  
• IN hard to reach places Apply glue with a special brush.

Wallpapers represent one of the most available materials for finishing even not very high-quality and even walls. They can perfectly hide uneven spots and even distortions. But gluing them on a completely crooked surface is not easy, inconvenient, sometimes even impossible. Therefore, the first step is to maximize, and the corners should be given the greatest attention. If in other areas of the wall the wallpaper became elastic from being impregnated with glue and could stretch, then on crooked corners, both internal and external, surprises in the form of distortions and large folds are not excluded.

Even at perfectly straight corners, difficulties sometimes arise. Therefore, before starting work, you should be well prepared for gluing wallpaper in the corners.

Where to start gluing?

Many recommend from the window, and some from the door. In reality, there is no difference, unless you take into account past trends when wallpaper had a special edge for overlap. Because of this, they had to be glued with an overlap of at least 1 cm. In this case, the best option was to glue it from the far wall with the window. So the seams were not visible when entering the room. Today, wallpapers are produced without this edge, and it is recommended to glue them end-to-end. Wallpapering corners is no different from flat spaces.

The first step is to decide what kind of wallpaper there are and how much glue is required to impregnate them:

• Paper ones require moderate impregnation and pre-coating of the wall.
• Vinyl ones require good impregnation, especially when pasting them in corners, since they are quite thick and dense.
• Non-woven wallpaper requires impregnation of only the wall.

Tools used for wallpapering.

Often the wallpaper has a pattern on it that is not resistant to mechanical damage. Therefore, a special rubber roller or brush is required to smooth them out.

Finishing internal corners

Having figured out the types of canvases and the amount of glue, you can get to work. If the wallpaper started to stick from the corner, then mandatory Using a long level and a metal ruler, it is necessary to apply markings in the form of a vertical line.

It should be positioned so that when gluing, the sheet lies with a fold at an angle of 2-3 cm. The inner corner is the least noticeable, so even if a small overlap forms there, it will not be very noticeable.

If, when gluing the canvas, the edge of the sheet is not straight, then it can be trimmed using a wallpaper or mounting knife. It is recommended to break off the blade after each cut. Otherwise, the next time you use it, scuffs and tears will occur.

The corner is where the wallpaper is most susceptible to peeling off the wall. Therefore, you should not skimp on glue here; the best option would be to pre-impregnate the surface in several layers.

To reliably glue the corners, use special glue. PVA glue is perfect.

Wallpapering the outer corners

The rules for wallpapering on the outer corners are to fit the canvas perfectly. The option with an overlap will not work here, because it will be clearly visible. The best option will be "Cutting". But to decorate beautifully external corner, its surface is necessary.

Next, it is recommended to pre-coat the wall surface with several layers of glue. If necessary, you should use a brush because it is often impossible to get into small cracks with a roller. The pre-impregnated sheet is glued to a corner with a 2-3 cm bend on the second wall. In this case, an uneven edge of the sheet is almost always formed. This is due to the geometry of the walls and their imperfection. The second sheet of wallpaper is pasted with an overlap of 5-8 cm over the previous one. This is necessary so that it can be comfortably grasped when removing it.

Then, using a plumb line, or better yet, a long level, cut both panels with a new blade of a mounting knife.

You should not save money here, because when the blade becomes dull, nicks can form on the surface, which will become very unattractive.

After making the cut, the excess piece is removed, and the edges of the joined sheets are carefully peeled off. The cut residue is removed from underneath and the wallpaper is glued in place. If necessary, you can add glue.

The appearance of the interior is now being presented high demands. Owners of Khrushchev apartments, who have repeatedly glued paper trellises in their apartments, now do not dare to begin repairs with their own hands. They don't know how to put wallpaper in the corners to make the room look good. Vinyl and non-woven fabrics are more difficult to work with. They are heavy and require certain skills. If you properly seal the corners with wallpaper, then the next repair will not happen soon.

How to glue wallpaper in corners?

Uneven corners frighten novice craftsmen, but even ones are very rare

It is difficult to bring two planes together perfectly. Therefore, even with smooth walls the angles have a lot of deviations. I had a lot of work and Vadik had to decorate his aunts’ apartments on his own. He was hesitant to start because he didn’t know how to properly glue wallpaper in the corners.

We glue wallpaper in the room

I decided to show my friend how to wallpaper the rooms of old houses in practice. One of my teams was renovating an apartment in a historical building. Vadik could see:

• preparation;
• alignment methods;
• how to use perforated corners;
• finishing the room.

The technology for finishing corners with wallpaper of all types is the same. Only thin paper trellises and fiberglass webs can differ. Work must begin from front door rooms when gluing end to end. When applying the edges of strips of thin trellises - away from the window.

Preparation and leveling makes subsequent finishing easier

Correctly gluing wallpaper in corners

When doing renovations in old apartments, I always putty the walls and install perforated corners. They simultaneously serve as beacons and protect the ledges from destruction. I choose cardboard ones if the inner corners have slight unevenness. In all other cases I use a PVC profile.

1. I'm checking laser level verticality of the walls. You can use a plumb line. I choose a flatter base surface.
2. I putty and embed the profile in the solution, leveling it.
3. After drying, I smooth it with another layer of putty. For paper and non-woven wallpaper I use an additional finishing compound.

If customers don’t want to spend money on leveling and corners, then I simply fill in large depressions. I cover the corner with wallpaper, cut a strip 10–12 cm wide. I place it evenly on both walls, making cuts for a tight fit. After this, it is easier to glue wallpaper in the corners. If the top fabric has to be cut or the paper trellises burst, then thanks to the background made of the same material it will not be noticeable.

We glue wallpaper in the corners ourselves

Advice! It’s better to align the corners well once than to fool your head every time you wallpaper a room.

Paste over the protrusions

The last strip in front of the corner is cut off so that it extends onto the other wall by approximately 2–5 cm, depending on the curvature. The greater the differences, the wider the approach. It should completely cover the most convex place by at least 8 mm.

For a better fit, I make notches with a sharp knife or just cuts with scissors. It is desirable that they be inclined towards the edge. I cover the corners with wallpaper and smooth out the main part first, then the strip around the corner.

How to glue wallpaper in the corners of an apartment?

Before you start gluing the wall from the corner, measure the width of the trellis and draw a line vertically along the level. I also check the condition of the corner. Lateral surface The strips should go along the deepest dent. I paste it strictly vertically, according to the markings. Near the corner the edge lies flat. The protrusions are hidden under the wallpaper that was pasted earlier.

It is better to cut wallpaper with large patterns so that the lines match. A slight shift will not be noticeable.

Fat vinyl wallpaper I cut along the ruler at a distance of 2 mm from the edge of the top sheet. With a sharp knife I cut both pieces strictly vertically along the entire height. I remove the excess and the canvases lie end to end. For strength, I put a painting mesh.

We glue wallpaper in the corners with our own hands

Advice! Use clear glue.

We start gluing from the door

My friend was able to see everything and now wallpapering in the corners did not scare him. Before you start finishing the room, you should draw vertical lines and check the condition of the corners. If there is no professional level, you can use a weight on a thread.

1. We glue it with an overlap of up to 5 cm on the adjacent wall.
2. Smooth the main fabric to the corner and glue it.
3. We make cuts and tightly fill all the unevenness with wallpaper.
4. We mark the vertical and, taking into account the pattern, glue the next strip end-to-end to the corner.
5. Using a ruler, we cut both sheets at a distance of 1–2 cm.
6. Remove excess pieces of wallpaper.
7. By bending both edges we glue the painting mesh. Coats it with additional glue.
8. We connect the strips end to end along the cutting line and press.

Before gluing wallpaper in the corners, make an approximate marking of the location of the stripes on all walls. If a piece of wallpaper ends close to a corner, immediately move the first strip. You can start with a strip cut along the length.

Simple techniques to hide unevenness by combining

We glue the wallpaper evenly on the corners

I told Vadik earlier that to create original interior combination with different drawings and tones. After the excursion to old building, he expressed the opinion that designers came up with such a technique to hide defects.

Before starting renovations, consider options for decorating the interior with companion wallpaper. First, cover the walls with trellises with a pattern, extending onto the adjacent wall. Then you create the transition with plain stripes. The cutting lines will visually look like straight corners. Irregularities will not be noticeable.

We glue wallpaper in the corners

For those with no experience, combining is more accessible than wallpapering with a pattern. At the same time, you adjust the shape of the room and enlarge it.