The door handle is the most necessary element For interior door. Opening a sash - swinging, sliding, folding - without this device is extremely inconvenient, so it is a more popular accessory than the same lock or latch.

Door handle: classification

These devices can have quite a variety of forms, but are divided into two large groups.

• Stationary – have no connection with the lock and are installed as an independent device. The handle serves only to grasp it and open or close the sash. It is usually attached with screws to almost any surface. The design of the handle can be very diverse. The most popular form was and remains U-shaped, in the form of a bracket, which is fixed vertically. If there is still a need to restrict access to the room, a roller latch is mounted on the sash from inside the room. The photo shows a stationary view of the fittings on an interior door.

• Push ones - their mechanism is somewhat more complicated. The presence of a latch requires cutting into the door leaf and forming a corresponding groove in the frame. When pressed, the spring moves the latch tongue and the door opens. When the handle is free, the latch is in the extended position and the sash can simply be slammed shut. This method ensures a tighter fit of the sash to the frame, which means higher sound and heat insulation of the room.

The mechanism provides the possibility of emergency opening: with front side There is a slot that allows you to use a screwdriver or other flat object to open the locked door.

Push ones are divided into two categories.

• With a one-piece pallet cover - mounted through a lock. You should pay attention to the axial rod on which the fittings are placed - it must be equal to the thickness door leaf. The length of the element can be adjusted. In the event of a breakdown, the entire mechanism must be replaced. The photo shows a sample.
• With separate escutcheons – installed with or without a lock. What matters here is the size of the pads and the size of the key hole.

• Knobs - pens round shape, are a type of push-on, but may also be known as rotary. The action is similar, but to open the sash you need to turn the knob. Usually the mechanism is equipped with a locking button, pressing which allows you to turn the ball on the other side of the interior door and open it. For emergency tearing, there is also a slot on the front side of the device. In the photo there is a handle-knob installed on an interior door.

How to disassemble a stationary door handle

Since its structure is the simplest, breakdowns associated with stationary fittings rarely occur. As a rule, the need to disassemble the handle arises when the owner wants to change an outdated or unsuitable model. IN in this case The steps are very simple: use a flat-end screwdriver to unscrew the screws and remove the handle.

An option is possible when the fittings on both sides of the door are installed on a common axial rod. This is checked this way: the handle is held on one side, and on the opposite side it is turned counterclockwise. If the fragment unscrews, then the fittings are rod-shaped. You just need to carefully unscrew the first fragment, and then remove the second one from the door.

How to disassemble I press the handle

In this case, it will take a little more time, since it is known in advance that both pieces of fittings are connected by one rod.

1. Use a screwdriver to remove the screws holding the trim. The pallet is removed.
2. The tetrahedral retaining rod should be inspected. In some models, the axial element and fittings are additionally equipped with a fixing rod with a cap. If this is the case, then the rod holding the element is removed, and the fittings are easily unscrewed from the axle.
3. The second fragment is removed from the web along with the axial rod. The second cover must first be removed.

How to disassemble round fittings

The sequence of actions is almost the same. To disassemble the mechanism, you will need a flat-head screwdriver and a key with a stop included in the lock kit. If the key is missing, any other object with a thin point will do.

1. On the side where the nob is located without a key, simply turn it, use a screwdriver to pry up and remove the cover.
2. The nob fixes the mechanism stopper. In order to disassemble the fittings, you should hold the stopper with a key or other object with a thin end, and remove the released fragment.
3. Using a screwdriver, remove both pieces of hardware from the front and end sides of the canvas.
4. The screws holding the halyard latch are unscrewed and the mechanism is removed.

The video shows how to disassemble the door handle in more detail.

Door hardware is a mandatory element with rare exceptions, and even in this case we are not talking about its complete absence, but about invisibility. There are the most different types these accessories, however door handles Knob for interior doors can be called the most popular option.

Type of fittings

The appearance of accessories can be very diverse - from elegant Italian products to deliberately rough ones that imitate antiquity. More important is the design of the fixture.

Based on this feature, there are 3 main types of fittings.

• Overhead – or stationary. They do not include any locking mechanisms and serve only to open or close the sash. The shape of the accessory can be very diverse: U-shaped, round, sculptural. This handle can be disassembled using a regular screwdriver.
• Push - turns on the locking mechanism. When you press the pressure lever, usually L-shaped, the force is transmitted through a special rod and removes the latch tongue from keyway. In this way, the interior door is opened.
• Knob - have a round, oval or other three-dimensional shape, although in fact they are from other types door hardware They are distinguished by the presence of a more complex lock, which allows you to lock the room from the inside. This option is very common in living rooms and hotels, but is also rare in apartments. The photo shows an elegant version of the accessory.

Accessories are made from the most different materials. Moreover, both the style of the product itself and the design of the fittings are important. So, for the pressure version, metal is most often used, less often plastic - the latter is too soft and fragile and, if pressed too intensely, quickly becomes unusable. The overhead model is made of wood, metal, and plastic.

For a round model, metal and glass, both silicate and organic, are most often used. As a rule, glass is painted in different colors, patterns are formed and even an image is formed in the depth of the object. No less popular is the option of combining metal with glass. This combination is especially effective with sculptural fittings.

The design of the knob handle for an interior door is quite simple, which makes it easy to disassemble and repair the hardware if it breaks. You can deal with this yourself.

Knob disassembly diagram

The fittings, especially if we are not talking about an elegant product from Italy, but about a completely ordinary imitation from China, break quite easily. The fact is that for such cases no serious locking mechanism is provided, so this kind of product is made from fairly soft alloys.

Side handle interior space A locking pin holds it inside the sash. For smooth running, it is equipped with a spring. In fact, to disassemble and repair the lock, it is quite enough to press on the pin with a thin, sharp object. But, as a rule, the latter is invisible, so they act somewhat differently.

How to disassemble the knob handle of an interior door?

1. First, remove all decorative trims that do not allow access to the mechanism. The linings are attached with ordinary screws, which are unscrewed with a screwdriver.
2. Then, with a thin, sharp tool, like a screwdriver or an awl, press down on the locking pin and pull out the handle. The photo shows the removal of the knob.
3. Then, at the end of the canvas, where the latch comes out, unscrew the bar. Usually this is enough Phillips screwdriver, however, there are models that require special tools.
4. Use a screwdriver to pry up the bar and carefully pull out the latch.

How to repair a product depends on the damage.

Typically, springs become stuck or weakened, but other damage can also occur.

How to repair the knob handle of an interior door with various damages is demonstrated in the video.

An attentive and responsible owner takes time to repair and replace worn-out household items. Door handle – functional element accessories, with which various problems occur due to frequent use: the mechanism can jam or click. Often the fastening points become loose, causing the handle to become loose and uncomfortable to use. To find out which element has worn out and broken, you need to gain access to the inside of the product. Thus, in order to replace outdated parts or the entire product with a new one, you need to dismantle the fastening from the door leaf. To do this, you should consider in advance the question of how to disassemble the door handle. By becoming familiar with the best method, you can reduce your time and effort.

Depending on what type of fitting this element belongs to, the technology for its removal and disassembly will differ. You can easily find out how to remove a handle from a door using step-by-step scheme parsing. The main types of structures: stationary, push, rotary or knob handle. Removing a stationary handle from a door is easiest, since it is in no way connected to the lock mechanism. Accordingly, when removing, the push and turn are disassembled.

When may dismantling be necessary?

• Breaking. How more complex design product, the higher the likelihood of an early breakdown. It is also worth paying attention to the cost: door fittings that are too cheap are unlikely to last long. In addition, if the door is used frequently, the fastening may become unusable faster. Therefore, when choosing a product, you should take into account its intensity of use. Where the pen is not used very often, you can choose cheap options. If the handle will have to be repeatedly exposed to workload during the day (for example, for a bathroom door), you should choose a product with high strength ratings.
• Planned renovation of the premises. When creating a new room design, often old products “do not fit” into the new design picture.
• Scuffs on the surfaces of decorative elements. Usually the first ones to fail are internal parts, especially the locking parts and locking tabs. But sometimes the inner part serves for a long time without breaking, and the outer surface takes on a worn and shabby appearance. In this case, you should consider replacing it.

Stationary handle

Stationary door handles differ from similar products in their simplicity. They are not connected to the lock mechanism and are secured with self-tapping screws or self-tapping screws. Removing and replacing them is not difficult. You just need to unscrew the fastening elements and release the product.

There is another option. If the screws are not visible, you need to rotate one part of the product to the side while holding the other part in place. This is typical for stationary round mounts. They are usually fixed using a main axis.

Lever handle

The push structure has an internal mechanism that connects it to the locking tongue. As a rule, these are “L”-shaped products. When you press it, the tongue disappears into the doorway and the door opens freely. The deeper the tongue goes into the hole in the doorway, the more pressure you need to apply. Accordingly, a design that does not require deep pressing is more convenient to use. Fastening is carried out immediately on both sides of the door. General procedure for removing a push-type product:

• Remove the main part. There is usually a bolt or screw on the bottom of the handle that needs to be unscrewed.
• It is necessary to remove the decorative trim, which hides the screws securing the main part of the structure. The cover plate is in most cases attached using threads.
• Unscrew the screws and pull the part towards you, holding the fastener on the other side of the door leaf.
• Taking off design on both sides, you can start releasing the lock.

Knob handle

The peculiarity of the Knob design is that a lock is embedded in its center. At the same time, it may outwardly resemble a conventional rotary or push version. This type of product is most prone to frequent breakdowns, therefore, the relevant question for the owner is how to disassemble a round door handle. Disassembling this design can be more difficult than other types of door hardware.

Before disassembling it, you should look carefully and find where the pin is located. It is usually located on the side of the room and helps secure the handle to the door. You may have to tinker around to find it, as it may be hidden under a decorative trim. A special key with a stop is often included in the kit when sold.

• Using a screwdriver or other object, clamp the pin.
• Remove one handle and unscrew the screws.
• Remove the second handle.
• Unscrew the bolts and release the lock.

Understand The question of how to mount the knob is not difficult. You need to do all the same manipulations in reverse order.

Round handle with rosette

The method of removing it differs in that it usually requires separating the elements manually. The part that is located closer to the door leaf should be held, and top part crank This will remove the top piece from the thread.

The second step is to remove the socket, unscrew the screws and remove the axle. Dismantling should be carried out carefully to avoid damage to decorative elements.

Dismantling and disassembling door hardware will not be difficult if you carefully and thoughtfully familiarize yourself with the features of its internal structure.

We often have to deal with situations such as repairing a door handle, replacing it, or reinstalling it on another panel. The process of removing this element itself is simple, especially if the structure is not equipped with a locking mechanism. How to disassemble a door handle correctly? To do this, you must adhere to certain rules.

Accessories that are distinguished by their beauty and good quality, serves as a wonderful decorative element for any door. Handles familiar to everyone allow you to easily enter and exit the door and use it. Modern industry produces a huge variety of such products, differing in color, shape, quality, price, and material of manufacture.

To ensure that the door is securely fixed in one position and does not open at the slightest movement, it is equipped with a special handle with a latch. This device should ensure soft and smooth movement of the structure. Special attention products of rounded shapes, the lock of which is equipped with a drum closing mechanism, deserve. This requires dismantling the device. In order to carry out such work clearly and systematically, you should prepare necessary equipment:

• Phillips or flat screwdriver;
• key with stop;
• adjustable wrench and pliers.

How to disassemble a round door handle? This problem interests most of the craftsmen who carry out repairs and door reinstallation. Typically, these elements on the same plane have a special locking mechanism that is operated by a key. Having prepared the necessary devices for work, you can begin dismantling. How to remove a door handle? To do this, use a flat screwdriver, which can easily remove the decorative elements of the mechanism.

Then they are removed from the valves located at the points where the handles are located. Then, using a key or other pointed product, you need to press on the stopper that appears. At the same time, the handle should be pulled and removed. The screws that appear are unscrewed with a Phillips or flat-head screwdriver. Next, the two halves of the mechanism are removed from the canvas. All screws are removed. The product should be disassembled in the same sequence, observing the reverse order. You need to start by fixing the latch on the canvas.

It is placed with the beveled part of the tongue at the opening point of the structure, then the part is fixed with two screws. After this, the handle parts are installed, it has a turnkey drum device. WITH reverse side a clamping element is placed, then it is secured with screws. During the work, it is necessary to monitor the tightness of the screws, slightly turn the door element and return it to its original position.

If desired, you can center this element. The decorative part is fixed to a given point. The clamping part, fixed to the canvas earlier, is intended for installation of a moving element on it. You should pay attention to the correct location of the square tube and the plate at its base. How to disassemble the handle? To ensure the work is done accurately, it is necessary to rotate the fixing part so that the opening coincides with the hole square shape in the position that the tube has a similar configuration with a flattened plate.

Now you can install the product in its place. After it is in the stopper, you need to apply pressure in a transverse position relative to the clamping element, pressing it in. The part of the product that is being removed should be pushed onto this part all the way. Now you can install decorative element. For such purposes, it is combined in grooves and put on to the base.

Don't forget to check the handle for strength. After installation, you need to test the effect of this door element, and from both sides. It is necessary to monitor proper work latch and drum device with a key. Any shortcomings that have appeared should be eliminated.

How to disassemble the handle correctly? You can do this simple job on our own, you just need to strictly follow certain steps. Most often, products with latches and locks are installed on interior doors. In order to better understand how to remove the handle, we suggest that you familiarize yourself with the main stages of the process of dismantling this element.

1. Study the structure of the handle design. You need to carefully examine it and determine the method of connection to the door.
2. Unscrew the fasteners and release the product.
3. Unscrew the handle from the interior door, attached to a separate base. Unfasten the spindle. In the same way, release the product from opposite side door leaf.

If the door leaf needs to be painted in the future, then it is necessary to remove the layer of old paint and clean the base with emery cloth. Then the door must be washed with water detergents, after this the surface should dry. After sanding the canvas, you can begin painting it. To perform the above work and install a new handle, you may need:

• different types of screwdrivers;
• bucket, napkin;
• putty, spatula;
• fine-grain sandpaper;
• grinding block;
• awl;
• drill;
• new door handle with lock, spindle and fasteners.

Installation of a new handle is carried out in a certain sequence.

1. 1. Screw in the spindle.
   2. Using an awl, make marks for the screws that secure the new product.
   3. Put the handle back in place.
   4. Make markings. Fix the spindle in the opening by putting a part of the product on it. The awl will help determine the location of the new fasteners that are inserted into the holes of the handle.

1. Make indentations at the desired points. Tightly covering the door requires the use of an electric drill.
2. Similar actions are carried out on the reverse side of the canvas.
3. The handle is fixed on the spindle and attached to the door leaf. In this way, its other part is attached on the reverse side.

Any new product must completely cover the screw holes. If they remain visible, they are sealed with wood filler. Taking advantage sandpaper, you can achieve perfect polishing surface, then it can be painted. The product with a shorter base is replaced with a new one included in the kit. Any element of a pressing nature is represented by the right and left parts; they can have an identical appearance if the spindle is located in the middle of the mechanism.

It is important here to trace the direction of rotation of the product before starting installation. Otherwise, it may be installed incorrectly and when the door is opened, instead of moving down, it will move up. To the front part locking device To restore the former radiance, it is removed before installation. Unscrew 2 screws and lift the tongue. old paint removed using a special liquid, after which the tongue returns to the specified position.

In order to paint the canvas yourself, the handle is removed. Next, the place that was covered with it is well coated. In this way you can protect the fittings from getting enamel on its surface. Giving the door a new tone should involve applying two layers of paint to the surface. If desired, the canvas can be treated with different colors on both sides. To do this, the shade of the surface on which the hinges are located is applied to the end parts.

Clearly and correctly assembled and installed fittings will ensure easy opening and closing of the door regardless of the sides. If visible defects are detected or elements become loose, they must be tightened and adjusted.

How to disassemble an interior door handle or kitchen door? Each of us may face this question sooner or later. Breakdown of this mechanism occurs due to its regular use. However, like any other mechanism, the door handle handle is designed for a certain number of jobs, after which the mechanism needs to be overhauled or replaced.

Various options for interior door handles

In this text we will look at how to disassemble the interior door structure handles, and we will clearly demonstrate the simplicity of this procedure, after which everyone can do it independently at home, having at hand a small set of tools and two hours of free time to disassemble such an element as the handle mechanism. It is worth noting that there are currently many different door opening mechanisms, so let’s look at examples of disassembling the most popular and in demand models today.

Device diagram and door handle mechanism

In this case, we will begin the analysis of examples with the rules for disassembling an ordinary stationary handle, which does not have a push set and mortise lock under the response larva. Here we need a flathead or Phillips screwdriver or a screwdriver with a bat. Let's look at an example of parsing a regular stationary handle:

Read also

Installing door handles on interior doors

In the case of a stationary handle, the entire disassembly consists of removing the decorative trim and unscrewing the fasteners. Next, a new mechanism or an old element with new fasteners is installed in its place.

Handle disassembly process

It is worth noting that replacing a stationary handle with a new mechanism requires additional manufacturing of the corresponding fitting grooves in the door leaf.

Disassembling a round handle with a rosette

A socket, as a rule, refers to a mechanism that allows you to lock a lock using a special small key on one side and an accessible thumb on the reverse. In this case, disassembling such a mechanism consists of the following steps:

If the handle requires repair or replacement of a certain mechanism, then you will have to completely disassemble the individual parts and find the cause of the malfunction.

Important. When disassembling a round handle with a rosette, all fastening elements must not be lost, otherwise you will not be able to assemble the mechanism together and install it in its original place after reassembling and replacing one of the parts.

Watch the video: door handle repair.

Disassembling the round knob handle

How to disassemble a round door handle-knob? This question interests many owners when entering new apartment, where door leaves with a non-removable handle mechanism are installed. In this case, to remove this element from the door leaf, as a rule, the following steps are performed:

Such an element as non-separable round handle secured using conventional mounting bolts. The mechanism is designed in such a way that it will not be carried out later renovation work, and a new cover will be immediately purchased and will take the place of the old handle.

It is worth noting that this process is associated with the purchase and replacement of a mechanism; otherwise, there is no point in removing and attempting to disassemble such an element.


Since the manufacturer did not provide options for repair and installation of the handle after repair in its original place.