The main decoration of the New Year is certainly the green forest beauty, which should be installed in such a way that during the celebration it does not fall and unforeseen situations arise.

Of course, today there are a lot of different options, due to which the process of installing a Christmas tree occurs in a matter of minutes. This includes various crosspieces, spacers, and factory-made fasteners. However, sometimes it is necessary to install a Christmas tree without a cross, and we would like to talk about how to do this most optimally.

Standard installation of a Christmas tree in the sand

It involves placing the green beauty in conditions close to natural, due to which the tree does not lose its attractiveness for a long time and can delight others for a whole month.

The process of installing a Christmas tree in sand is carried out in the following sequence:

• The tree trunk is leveled (using a hacksaw, the edge of the trunk should be trimmed so that an even cut is obtained);
• Using wooden blocks 150 - 200 mm long, reinforcement is made, for which the materials are knocked together crosswise and the entire resulting structure is nailed to the end of the Christmas tree trunk;
• The trunk treated in this way is placed on the bottom of the bucket, and the entire tank is filled with raw, clean sand.

To ensure moisture, the sand should be periodically watered with warm, slightly sweetened water.

High-speed installation of a Christmas tree

A more innovative solution is quick installation Christmas tree using a bucket and plastic bottles(volume 1.5 - 2 liters). The essence of this method comes down to the fact that plastic bottles are filled with water (not to capacity) and installed vertically in a bucket around the perimeter in such a way as to provide clearance for installing the barrel. After this, the tree trunk is forcefully inserted into the cavity formed in the middle, and the tree is properly fixed in the bucket.

Essentially, the water bottles act as spacers and hold the tree trunk in position in the bucket. The advantages of this method are obvious:

• You can install a Christmas tree with any trunk diameter (by selecting plastic bottles of a certain size);
• Absolute cleanliness during work (unlike installation in sand, with this option there is absolutely no debris generated);
• Speed ​​of work (you can install a Christmas tree without a cross using plastic bottles within a couple of minutes).

Watering such a Christmas tree is also not difficult and warm water Simply pour it into a bucket (5cm from the bottom) and add it periodically as needed.

From all of the above, we can conclude that installing a Christmas tree is a very responsible procedure, which, if you follow all the recommendations, can be done independently.

Found. But since I promised to show a couple of options for installing a Christmas tree on a quick fix, then you will have to make a new one. This is a simple matter, but you never know, maybe it will be useful to someone.

I’ll make a reservation right away. By Christmas tree I mean a coniferous tree at least two meters high. You can stick a meter-long stump into a bucket of sand and not have to worry about it. But, to be honest, this is not a Christmas tree. This is a potted plant. A Christmas tree is when the star is above your head, not under your armpit. I have nothing against artificial ones. Beautiful, practical, convenient. Just a view plastic Christmas tree always brings me to the same thought. If the Christmas tree is artificial, then why isn’t Olivier made of papier-mâché? Logically, if the Christmas tree is plastic, then the herring under the fur coat should be synthetic. Plastic champagne, plastic caviar, dummies instead of gifts, inflatable latex guests. Convenient, practical, beautiful. No one falls face down on a salad, no one vomits vinaigrette in the toilet, no need to wash or finish anything, wipe it with a cloth in the morning and put it away. And that’s it, I forgot. Well, isn't that great?

In short, I am a supporter of a living Christmas tree. And I try, whenever possible, to go to the forest rather than to the market to get it. It’s not about money, it’s just strange somehow, living in the forest, to buy a Christmas tree at the market from Azerbaijanis. A Christmas tree is not a watermelon. But by and large, it doesn’t matter where the tree comes from, the main thing is that it exists. And when there is a Christmas tree, you need to put it up somehow.

There are a million ways and options. You can stupidly buy a crosspiece like this at the market or Christmas tree market.

I won’t talk about the disadvantages of this method; anyone who has encountered it knows. If you don’t have the time, opportunity, or desire to do this, then there are several simple, practice-tested ways to install a Christmas tree carefully and reliably with your own hands.

Option one. Cross.

In my understanding, the crosspiece should be of such a design that it would hold the tree in the presence of chaotically moving objects in the house, such as dogs, cats, children, drunk relatives. The only way to knock her down was to fall flat from the stool. You can make a reliable crosspiece in an hour with straight arms and a minimum of tools. With experience - half an hour maximum. In general, according to the mind, the cross is made each time for a specific Christmas tree. He throws it out with her.

What is needed for this?

Some kind of wooden base. Anything will do, a board, a block, a picket from a neighbor's fence. Last year I bombed a pallet that happened to turn up in the yard. It didn’t turn out particularly beautiful, but it was reliable.

This time the base will be a 5x4 block like this.

To be honest, it should be wider. The wider the beam, the more securely it holds the tree. But it is what it is.

Tool. The maximum set is a tape measure, a hacksaw, a pencil, a square, a drill, a screwdriver, and a dozen self-tapping screws. Minimum set - hacksaw, tape measure, hammer, a dozen nails.

We cut off, trying to maintain a semblance of a right angle.


Let's figure out how it will all fit together.


We measure the thickness of the butt of the tree. (Since our hole is square, then the butt can, in principle, be cut and made square. But if you don’t have experience, it’s better not to. You can wear out the tree and be exhausted yourself)

We set aside this distance from the edge of each block. (It’s better to take a little less so that the butt grips well. My butt thickness is a little more than five centimeters. I set aside exactly five.)

I immediately set aside the second distance, the line along which the bars will join. This is half the thickness of the bar.

Drill a couple of holes along the line for self-tapping screws.


Since my timber is thick and the screws are not particularly long, the holes will have to be countersunk.

Done, ready to assemble.

This is what ended up happening.

What's missing from this cross? Just like those sold on the market. For a tree to stand longer, it needs moisture. The butt must be in the water. Cut four cubes from the same block.

We drill, countersink, screw.

Well, that's all in principle. You can put up a Christmas tree. Having previously placed some kind of water cap at the bottom.
If necessary, level the trunk with wedges.

Second way. Cup.

This option does not require any tools other than a screwdriver and a dozen screws. You also need some kind of massive base. On my balcony there are two scraps of kitchen countertops left over from installing the stove and sink. You still need three corners. There is an abundance of such corners in every household store.


Everything is quite simple here. Find the center and draw a circle.


We put the corners and screw them in.


You can put up a Christmas tree and secure it. Five minutes of time.
If you wish, you can take a polypropylene plumbing pipe of a suitable diameter


and cut a piece from it.


You will get a glass.


Having pulled a pair of condoms onto it from below, you can safely pour water.


A not particularly aesthetic appearance can be easily draped with improvised means.
Well, that seems to be all. All this homemade work took me three times less time than writing the post.

Option three. Stool.

If you’re on the edge and don’t have anything at hand, you can stupidly turn the kitchen stool over and tie the Christmas tree to the legs :))

And in conclusion.

If anyone has problems with their hands, or is a girl, then you can come and pick up this cross for yourself. I can even write on it “Hell of Daragoga Rocketcheg for eternal memory.”

If possible, show how and what your Christmas tree is. Just wondering.

About the quality of photographs.
Since during the shooting the shket left for some New Year's performance and took the camera with him, the pictures had to be taken with what was at hand. I had a test smartphone at hand

There is not much time left until the New Year. Soon many will start thinking about installing a holiday tree. By the way, we talked about it in a previous article of the same name. But bad luck... I can’t find the old stand. We suggest that you do not waste time looking for it (you will find it later), but quickly make a new wooden cross for the Christmas tree with your own hands.

You will need:

• bars (2 pcs.);
• wood hacksaw;
• drill with screwdriver and drill set different diameters;
• several screws;
• small piece metal pipe according to the diameter of the tree trunk.

Let's get started

1. First of all, treat each board well. Give them the desired length. Make sure that each end is level, otherwise skewing of the tree cannot be avoided.
2. Prepare the timber for assembling the stand. Measure 0.5 lengths and cut a groove, its length will be equal to the width of the block, and its depth will not be less? thickness. Cut such grooves in 2 blanks.
3. If you have PVA glue on hand, apply it to each groove. After it dries, additionally fasten the cross using self-tapping screws. This way you will be twice as safe from the fall of the tree. But do not drive the screws into the center of the future stand. There you still need to make a hole for the spruce trunk.
4. After assembling the crosspiece, take measurements of the diameter of the lower part of the tree trunk. Select the appropriate drill bit and make an opening in the crosspiece. If required diameter If you can’t find one, make a mark, drill small holes along it, right next to each other, and the middle will fall out on its own. Install a pipe into the hole.

Well, the simplest wooden cross for a Christmas tree has been assembled with your own hands and is ready for use! Now all that remains is to install the forest guest and dress her up along with the kids. You can also make a metal stand, but we will talk about this in another article.

• Even the most unsightly stand can be decorated in such a way that it becomes invisible. Your imagination will tell you what to use for this.
• Remember that the most basic characteristic of each of the stands, be it a wooden or metal cross, is stability!
• Never place the New Year's beauty close to any flammable device.
• Try not to leave the tree with the lights on overnight.

A live Christmas tree brings the holiday atmosphere and the smell of the forest into your home, but at the same time it causes a lot of headaches when it comes to installing it. In this material we will offer simple and functional solutions, which will solve this problem once and for all. Check out five designs for a wooden stand for a Christmas tree - they can be easily made with your own hands using simple blanks and a minimum of tools.

Crosspiece for small and medium-sized Christmas trees

The first project is a classic wooden cross. Its main difference is the absence of a half-tree connection, which eliminates the need for complex markings, work with a chisel and subsequent hassle with adjusting the connection.

A reliable and neat cross is made from four simple blanks - two boards (60x15x2.5 cm) and two square scraps (15x15x2.5 cm).

We determine the place where the boards will intersect. In our case, we measure 22.5 cm from the end of each board.

Using a square, we apply markings.

We do the same with the second board: measure 22.5 cm from the end and apply markings.

We lay the boards along the marking lines and check the accuracy of the fit using a square.

We connect the crosspiece with four screws or self-tapping screws.

We screw supports from square scraps along the edges of the top board.

We apply cross markings to determine the center into which the main rotor will be screwed in or a wide through hole will be drilled.

Drill a pilot hole.

For small trees, mounting with a 120 mm through screw will be sufficient. If desired feather drill you can make a wide through hole of the required diameter; a depth of 5 cm is enough for the tree trunk to be stably positioned in the cross.

Glue the felt pads. They will protect the floor from scratches and add stability to the cross.

The next project is simpler, but no less reliable option Christmas tree stand. A simple cross, assembled from four boards without unnecessary joints, will provide stable support for a tree of any size. Using a board with an uncut edge, traditional question: How to close the crosspiece - it will disappear by itself. The living edge will add decorativeness to this simple design, and make it a natural extension New Year's tree. After the holidays, the crosspiece elements can be easily disassembled and stored until next year.

From a pre-prepared board with one edge trimmed, we cut 4 pieces of the same length. We focus on the size of the tree: the larger it is, the longer the boards will be needed.

We drill guide holes in the faces and ends of the workpieces to avoid splitting when tightening the screws.

We assemble the structure on a flat plane and tighten it with screws. We drill a guide hole for the screw that will secure the tree trunk.

A simple and expressive style cross is ready.

The third project is a simple and stable wooden stand that can be adjusted to any trunk diameter. The crosspiece consists of three supporting elements. The optimal length of each part is 250 mm. Two parallel grooves are milled in the face of each of them. The ends of the boards are cut at an angle of 60°, and shallow guide holes for screws with wide washers are drilled into them. It is convenient to store the collapsible elements of the cross in a compact stack until the next holiday.

Milling grooves according to pre-applied markings.

High stand for large Christmas trees

Four elements, cut with a jigsaw according to the template suggested below, will easily turn into a beautiful and stable stand that can support a Christmas tree 2.5 meters or more in height. The structure is tightened using screws screwed into pre-prepared holes, and can also be easily disassembled without taking up extra space during storage. You can place a reservoir of water under the stand so that the spruce stands even longer and continues to fill the house with its unique scent.

Preparing for the main holiday of the year is a troublesome task. After all, there is so much that needs to be redone. The main thing is to install a Christmas tree as a symbol of the New Year. And if everyone approaches decorations responsibly with tinsel, toys and garlands, then they always forget about the stand. However, a stand that is not designed properly can ruin the entire look. In addition to beauty, it is important that the design ensures maximum stability of the New Year's tree. You can buy a stand or make it yourself from scrap materials.

DIY Christmas tree stand options

When you decide to make a stand with your own hands, you need to remember that it should not only provide stability, but also look beautiful. If the diameter of the spruce leg is small, and the tree itself is not tall, then a small stump is perfect as a stand. A stump about 30 cm high is enough. You will also need a drill, glitter for decoration, glue and a brush. It is necessary to drill a hole in the stump, equal in diameter to the spruce trunk. It must also be strictly perpendicular to the floor. After this, the stump needs to be covered with glue and sprinkled with glitter.

REFERENCE! If there is a crosspiece, but it is of an unpresentable appearance, you can give it a stylish look by using an ordinary one as a decorative element. wooden box. There is no need to close the box itself. It can be sanded a little and varnished. Place toys and other Christmas tree decorations inside.

If there is no crosspiece, you can make it yourself.

Wooden cross for a Christmas tree

This is the simplest and inexpensive way making a cross for a New Year's tree.

For it you will need:

1. Several bars.
2. Drill with drills of the required diameter.
3. Hacksaw or plane.
4. Self-tapping screws.
5. Glue.

Step by step execution:

1. First you need to prepare the bars. They need to be given the desired length by carefully trimming the ends. This must be done as smoothly as possible to avoid the tree swaying.
2. The next step will be cutting out the grooves. This can be done using a chisel. The depth of the groove should be approximately half the thickness of the block.
3. The resulting grooves must be covered with glue to securely fix the bars.
4. Next, you need to assemble the cross.
5. When the glue has completely set, the bars must be additionally secured with self-tapping screws. This is required to ensure the stability of the structure, since trees have considerable mass.
6. The final stage is drilling a hole in the middle of the resulting cross. Its diameter should be equal to the diameter of the tree.

ATTENTION! If you don’t have bars at hand, you can replace them with boards or MDF. Since their thickness is much less than that of the bars, and it is not possible to drill a hole, you need to attach something to them to install the tree. To do this, you can take, for example, an aluminum coffee can. You also need a plate to which the jar will be attached.

In this case:

• the can needs to be welded to the plate;
• for greater stability, additional stiffeners need to be welded to it;
• the boards must be glued together;
• Next, using self-tapping screws, attach the plate with the can to a cross made of boards or MDF.

After this, the jar needs to be decorated beautifully, for example, with tinsel, or you can make decorative gifts and put them under the tree.

Christmas tree stand made of metal

If available necessary tools, the stand can be made of metal.

For this you will need a pipe and rods. The diameter of the pipe must match the diameter of the tree trunk. Procedure:

1. The rods need to be fixed in a vice and using a hammer to give them the shape of future legs. This must be done extremely carefully to achieve maximum symmetry. Otherwise, the tree will sway after installation.
2. In order for the spruce to hold better in the inside of the pipe, it is necessary to make several grooves.
3. The legs are attached to the pipe using welding. If they worked out different lengths, the rods need to be cut using a grinder.
4. All ends of rods and pipes need to be processed sandpaper, to remove roughness.
5. Next, the resulting structure is painted in the desired color.
6. You need to place a jar of water under the pipe, and then install the Christmas tree.
7. If necessary, the stand can be disguised with tinsel.

After making the chosen version of the cross and installing the tree, you can begin decorating the New Year tree. This is how you can make a stand for a spruce tree with little effort and a minimum of materials.