Price - UAH 3,000 per gram, available
Doorhan Sliding 800, SL-800 drive

Reliable electromechanical Doorhan Sliding 800 drive was designed for automation sliding gates with a maximum curtain weight with sheathing up to 800 kg. Ideally suited for residential sliding gates such as country house, summer cottages, cottages, small parking lots or for a workshop. Intensity of use SL-800 is 50 percent, which is quite enough to service an average number of cars. Thanks to the introduction of new technologies, the automation works stably from -40 to + 60 degrees.

The main part of the drive body is made of high-strength duralumin and coated with a special layer with high protection from corrosion. The main mechanical elements and the control unit are enclosed in a sealed plastic casing. The control unit is also covered with a plastic cover and protects the electronic part from moisture and dust. Set Sliding 800 comes with built-in PCB-SL control unit. The PCB-SL is designed with an unstable voltage supply in mind. The control unit is located in such a way that the wires are easy to connect, as well as access to the main settings is located on the top panel of the PCB-SL.

Externally SL-800 drive similar in design to FAAC 741, 740. Automation mounts are located on both sides in 4 places, which facilitates installation. Thoughtful design will allow you to install and configure DoorHan drive in just a few hours. Like most modern automation in the drive Doorhan Sliding-800 there are several operating modes - this is "Automatic mode", separate control "Open" and "Close" and "Open-Stop-Close-Stop". In automatic mode, the sliding gate leaf will close after a certain time, which is easy to set in the control unit, both during installation and after installation. Separate control provides for the presence of the operator, one press on the control panel and the gate opened, another press and the gate closed. The third mode also provides for the presence of an operator, but in this case, so that Gates stopped, you need to press the remote control one more time. In addition, the control unit can be configured work time, pause time and increased engine operation. The open and closed position of the gate can be easily adjusted using magnetic proximity switches. Also, to protect vehicles from damage, Doorhan Photocell safety photocells (receiver and transmitter) with a range of 25 meters are supplied in the kit. If your electricity is often cut off, the drive is equipped with a system for transferring to manual mode, it is also called "Emergency mode". Manual translation is done in the same style as for automation FAAC. It will be possible to transfer to emergency mode using a special unique key that is supplied with each kit.

Technical characteristics of the Doorhan Sliding 800, SL-800 drive

On the this moment there are 3 modifications of actuators Doorhan sliding- it Sliding 800, Sliding 1300 and Sliding 2100. In this manual, we will consider SL-800 drive... This drive is powered by mains alternating current at 230 volts, while the power consumption is 250 watts, and the current consumption is 1 ampere. The gear ratio of the gearbox is 1 to 32. SL-800 supports rail type M4x12,566 mm. The gear wheel is metal Z16, and the maximum torque is 20-43 Nm. The maximum use intensity is 50%, Weight Limit gate 800 kg. The drive works reliably from -40 to +60 degrees. Built-in 10 μF capacitor.

Doorhan Sliding 800 drive set, price, installation, repair

At the moment, the drive kit Sliding 800 KIT consists of: drive unit with built-in PCB-SL control unit, M4 DHRACK toothed racks (4 pieces), Doorhan Lamp, Photocell safety photocells, Keyswitch. The complete set is priced at 366 euros. You can order from us as full set and accessories separately. In addition, our company is engaged in the installation and repair of Doorhan drives. Sliding 800.

You can download instructions for installation, configuration and repair on the same page.

The company "Gate Systems - Dnepropetrovsk" offers products of all world manufacturers of movable enclosing structures in the following areas:

Sectional garage and industrial doors: DoorHan Dorhan (Russia), ALUTECH Alutech (Belarus), Hormann Herman (Germany), Krispol Crispol (Poland), Ryterna Riterna (Lithuania), Circle(Czech)

Roller shutters (roller shutters) and roller shutters: DoorHan Dorhan (Russia), ALUTECH Alutech (Belarus)

Gate and roller shutter automatics: DoorHan Dorhan (Russia), Faac(Italy), CAME(Italy), Nice(Italy), Marantec(Germany), Sommer(Germany), Somfy(Germany).

Barriers: DoorHan(Russia), Faac(Italy), CAME(Italy), Nice(Italy)

Transfer equipment: DoorHan Dorhan (Russia), Hormann Hermann (Germany)

To order!

The reliable electromechanical operator Doorhan Sliding 800 was developed to automate sliding gates with a maximum door leaf weight with sheathing up to 800 kg. It is best suited for sliding gates for domestic use, for example, for a country house, summer cottage, cottage, small parking lot or for a workshop. The SL-800 is used at 50 percent, which is enough to service an average number of vehicles. Thanks to the introduction of new technologies, the automation works stably from -40 to + 60 degrees.

The main part of the drive body is made of high-strength duralumin and coated with a special layer with high corrosion protection. The main mechanical elements and the control unit are enclosed in a sealed plastic casing. The control unit is also covered with a plastic cover and protects the electronic part from moisture and dust. Sliding 800 kit comes with built-in PCB-SL control unit. The PCB-SL is designed with an unstable voltage supply in mind. The control unit is located in such a way that the wires are easy to connect, as well as access to the main settings is located on the top panel of the PCB-SL.

Externally, the SL-800 actuator is similar in design to the FAAC 741, 740. The automatics mounts are located on both sides in 4 places, which facilitates installation. A well thought-out design will allow you to install and configure the DoorHan drive in just a few hours. Like most modern automatics, the Doorhan Sliding-800 drive provides several operating modes - these are "Automatic mode", separate controls "Open" and "Close" and "Open-Stop-Close-Stop". In automatic mode, the sliding gate leaf will close after a certain time, which is easy to set in the control unit, both during installation and after installation. Separate control provides for the presence of the operator one press on the remote control and the gate opened, another press and closed. The third mode also provides for the presence of an operator, but in this case, in order for the gate to stop, it is necessary to press the remote control one more time. In addition, in the control unit, you can set the working time, pause time and engine boost. The open and closed position of the gate can be easily adjusted using magnetic proximity switches. Also, to protect vehicles from damage, Doorhan Photocell safety photocells (receiver and transmitter) with a range of 25 meters are supplied in the kit. If your electricity is often cut off, the drive is equipped with a system for transferring to manual mode, it is also called "Emergency mode". The manual translation is done in the same style as that of the FAAC automation. It will be possible to transfer to emergency mode using a special unique key that is supplied with each kit.

At the moment, there are 3 modifications of Doorhan Sliding drives - these are Sliding 800, Sliding 1300 and Sliding 2100. In this manual, we will consider the SL-800 drive. This actuator operates on 230 volts AC with a power consumption of 250 watts and a current consumption of 1 ampere. The gear ratio of the reducer is 1 to 32. The SL-800 supports the M4x12,566 mm rail type. The gear wheel is metal Z16, and the maximum torque is 20-43 Nm. The maximum intensity of use is 50%, the maximum weight of the gate is 800 kg. The drive works reliably from -40 to +60 degrees. Built-in capacitor
10 μF.

Doorhan Sliding 800 drive set, price, installation, repair

At the moment, the Sliding 800 KIT drive set consists of: a drive with an integrated PCB-SL control unit, M4 DHRACK toothed racks (4 pieces), a Doorhan Lamp signal lamp, Photocell safety photocells, a Keyswitch key switch. The complete set is priced at 366 euros. You can order both a complete set and components separately from us. In addition, our company is engaged in the installation and repair of Doorhan Sliding 800 drives.

Fully customizable overhead motor garage doors includes

• adjustment of the extreme positions of the upper and lower
• regulation of the force of the blade along the guides
• remote control programming

Instructions for adjusting the blade end positions of the Sectional-750 (SE-1200; Fast-750)

1_ Setting the upper end position of the garage door

Press and hold the "P" key until "1" lights up. Then release and press "P" again, "1" will start blinking.

2_ Setting the bottom position of the garage door leaf

Press and hold the "P" key until "1" lights up.

Final saving of the upper and lower position of the garage door leaf:

Pressing the "+" key set the number "1" on the display. Then press the "P" key for 5 seconds. The display shows "0".

The programming is fully saved and completed.

CONFIGURING THE REMOTE

Instructions for setting up the DorHan control panel for the Sectional-750 overhead drive (SE-1200; Fast-750)

On the display of the electric drive, press and hold the R button. One more zero should appear and go out for a second.

After that, select the desired button on the remote control and click on it twice. The remote is programmed!

VIDEO INSTRUCTION

Programming the remote SE-750 (SE-1200); Adjustment of the upper, lower position and force of the gate.

WE CONFIGURE THE SLIDING AUTOMATIC GATES

Instructions for setting up the DorKhan control panel for sliding gate drive Sliding 800 (SL-300; SL-1300; SL-2100)

1.Hold down the programming key of the electric drive board.

The indicator should flash.

Release the key and press the button on the DorKhan remote control (2 times), which was chosen for this opening of the device.

The remote control recording is over.

VIDEO INSTRUCTION

Programming the remote Sl-300 (Sl-800; Sl-1300; Sl-2100) new drive board; Drive board without protective cover.

DOWNLOAD INSTRUCTIONS DOORHAN SECTIONAL-750 ELECTRIC ACTUATOR PDF file format

Sliding 800 sliding gate electric drive produced by DoorHan Group of Companies (Russia) is the optimal solution for automation of private gates. Sliding 800 drive manufactured on modern high-tech equipment. The drive consists of two main units - electric motor with control board PCB-SL / V.1.0. with built-in radio receiver with a maximum number of programmable consoles in the amount of 60 pieces and a mechanical gearbox. The electric motor of the drive and the gearbox are installed in a single sealed robust housing and this factor actually allows the Sl-800 drive to work submerged in water almost to the control board itself. Therefore, the Sliding 800 sliding gate operator is very quiet and does not cause discomfort to the user. The Sliding 800 drive has a self-locking gearbox, which is unlocked with the key supplied in the kit and allows you to open the gate by hand in the event of a power outage. Electronic limit switches of the Sliding 800 electric drive reliably stop the motor in the set end positions of the door. Sliding-800 drive is controlled by wired closing contact or radio remote control remote control and can also be controlled by a combination of these controls.

The Sl-800 actuator, like its similar model Sl-300, is screwed with four nuts to the base on which it is mounted. The SLIDING 800 does not have a special mounting base. The Sliding 800 drive has a built-in electronic end reader DHSL041N, which is triggered to stop in end positions thanks to magnets that are mounted on a toothed rack on brackets of different polarity. These end magnets are always supplied with the actuator in the same box. Sliding 800 sliding gate drive has a built-in PCB-SL / V.1.0 control unit. This control board compares favorably with the previous series with easily removable and pluggable clip-on terminals. Control board PCB-SL / V.1.0. has a protective cover and protects it from accidental damage. Control board PCB-SL / V.1.0. equipped with a built-in radio receiver board for 60 consoles. New board PCB-SL / V.1.0. has all the functions you need most to use and has many new advantages:

The control board has multi-colored terminals that visually simplify connections necessary devices and control elements.

The control board has a nice option of slowing down the work before the end positions of work, namely, it is activated by DIP No. 4, which contributes to a significant increase in the service life of the operator and the gate.

The control board has an installable option for remote programming of consoles i.e. from an already programmed remote control, you can transmit and record a radio signal to a new remote control within the range of the control board receiver and you do not need to remove the drive cover.

- The board has a modernized input electrical circuit, and this is especially useful when the voltage level is unstable and thereby increases the board's service life.

SLIDING 800 Drive Specifications

Supply voltage - 220V / 50Hz

Rated power - 280 W

Gear ratio of the reducer - 1:32

Gear - Z16

Maximum linear force - 900N

Maximum moment - 20 Nm

Thermal protection - 120 0 С

Door leaf speed - 12 meters per minute

Maximum door leaf weight - 800 kg

Intensity of use - 50%

Range working temperature from - 20 to +55 0 С

Protection class - IP54

Control block - PCB-SL / V.1.0.

Limit switches - magnetic

Consumption current 2.1A

Capacitor capacity - 10 μF

The board has a self-resetting fuse made of polymer material with very low resistance. In the event of an overcurrent, the resistance rises sharply, knocking down the current as much as possible to a safe value.

The Sliding drive control board transformer has improved technical characteristics due to the increased cross-section of the winding wire and the optimized core.

The optimally matched value of the operating voltage of the varistor of the control board allows protecting the transformer and the board from high-voltage impulse noise.

The Sliding drive is programmed using fine tuning knobs and DIP switches. Conveniently program the desired functions

Sliding gates must comply with the standards EN 12605 and EN 12604.

- Before installing the SlIDING 800 actuator, it must be ensured that the climatic conditions are correct.

The SlIDING 800 is not intended to be mounted more than 2.5m above the ground.

- The SlIDING 800 must not be operated in areas with flammable substances and gases.

When installing the Sl-800 electric drive, you must use the tools specified in the instructions.

- When installing or maintenance Always disconnect the power supply to the SlIDING 800 drive.

If the Sl-800 operator is mounted on a gate with a built-in wicket, then it is imperative to install an open wicket sensor on the wicket.

The SlIDING 800 electric drive must not be left uncoupled, as uncontrolled movement of the door leaf can occur and it can break.

Always for safe work the gate must be fitted with a safety mechanical stop to restrict gate movement.
- Electric cables to the SlIDING 800 actuator must be laid by a qualified installer, and the power supply cable is laid in a protective corrugation.

Used cables for Sliding 800 drive and photocells

- Cable 2x0.5mm - photocell and step-by-step button for control.

4x0.5mm cable - photocell receiver.

Cable 3x2.5mm - power supply.

Doorhan SLIDING-800 operator for sliding gates weighing up to 800 kg

Possible complete set of DOORHAN Sliding-800 automation

DOORHAN Sliding-800 set minimum

DOORHAN Sliding-800 maximum set with safety accessories

The drive of this model is suitable for domestic or semi-industrial use.

In this article, I tried to talk as briefly and easily as possible about design features Sliding-800, as well as what in general you need to pay attention to when choosing automation.

• What does a consumer and industrial drive mean?
• Loads affecting the operation of automation
• Specifications DOORHAN Sliding-800
• Sliding-800 drive
• Self-locking drive
• Control unit electronic board
• Flush-mounted receiver
• Rack
• Remote control
• Magnetic limit switches
• Photocell safety
• Signal lamp
• Buying automation from us

What does a consumer and industrial drive mean?

By design, mechanisms are household, industrial, and also semi-industrial ones can be distinguished. All of them are characterized by an indicator of the intensity of use - this is a characteristic of the possible working time and the need for rest during a certain period of time.

Usually, drives with this indicator up to 40% are considered domestic, and those with a higher value are semi-industrial or industrial.

Sliding-800 automation can be described as a semi-industrial equipment that is capable of servicing the gates of private houses or small public parking lots, where the traffic flow is small.

To correctly determine what purpose the model is needed for your gate, I recommend that you contact one of our specialists for a free consultation.

The fact is that buying automation above the necessary capabilities, you can overpay even more than twice, and buying a drive less powerful than you need, you risk getting equipment burned out from constant overloads.

Loads affecting the operation of automation

When moving the gate, the drive must in normal mode (without overloads) overcome the following loads:

• Bundle weight and length
• Stiff gate movement
• Snow and ice
• Wind pressure

Weight and length sash load is understandable, which is constant. It should only be noted that the equipment passport indicates the maximum parameters of the gate, which cannot be used simultaneously, because they are inversely proportional. That is, the heavier the sash, the shorter its length should be, and vice versa.

Stiff gate movement... This load depends on the quality of the fittings. If there are distortions or wedging during the movement of the sash, this leads to an increase in the gate resistance, due to which the operator will have to work with increased effort.

Snow and ice... Fittings for low temperatures air may freeze and the automation will need additional force to move the sash.

If the door leaf has various decorative elements(planks or niches), these can become places where snow will accumulate and ice forms, which will weigh down the gate.

Wind pressure. When the sliding gates are moved, wind pressure is practically not transmitted to the drive, but it still affects its operation.

It is difficult to foresee the magnitude of these loads, and even more so to assemble them into a single whole, therefore our experts recommend lowering the specified parameters of the gates for equipment by a factor of 2-3, so that the mechanism works without overloads.

Specifications DOORHAN Sliding-800

The upper part of the drive housing is made of impact-resistant ABS plastic, and the lower part is made of powder-painted aluminum.

The case has an IP44 class and protects all elements inside from dust and moisture.

For the convenience of making all connections to the control unit, a special hole is made in the lower part of the drive.

The outer gear that drives the gear rack is made of steel, but the drive gear of the reducer is made of polymers, which is not the best technical solution to work in our climatic conditions.

The manufacturer indicates the temperature range for the normal operation of Sliding-800 from -200C to + 550C, and in most of our regions the temperature can be higher or lower than these values.

At low temperatures, polymers become brittle and break, and at high temperatures they become soft and lose their shape under stress.

The Sliding-800 drive electric motor operates on 220V and has a power of 250W.

Self-locking drive

Sliding-800 is a self-locking mechanism that, after stopping, will not allow the leaf to be moved manually, therefore, it is not essential to install a lock to lock the gate.

Blocking occurs due to the fact that all gear drives gearboxes are in constant mesh with each other.

If it is necessary to remove the lock and move the gate manually, for example, when the power is turned off, you need to use the unlocking mechanism.

For this you need:

• insert the key into the connector on the drive housing and turn it clockwise
• pull the special lever
• turn the key counterclockwise and remove it - the drive will be unlocked.

To return equipment to auto mode, the unlocking steps must be performed in the reverse order.

Control unit electronic board

For stable operation of the automation, the board has special filters to protect against electromagnetic interference.

On the board, all the terminals are signed, so it will not be difficult to connect it yourself. The board also has special connectors for connecting additional elements(safety photocells, signal lamp).

The board has light indicators for visual control of the automation operation.

It is located at the top under the drive cover and is additionally protected by a special case against dust and condensation.

When there is a need to make adjustments to the control board, there is no need to open its protective case, because all the fine tuning knobs are brought out of it.

The board has a special additional connector for connecting an antenna, which increases the range of the remote control.

It has a low impedance self-healing fuse. When an overcurrent occurs, the resistance of the fuse rises to knock down the current to a safe value.

When everything is back to normal, the fuse will restart itself and reduce its resistance.

In addition to a protective case against condensation and dust, the surface of the board is covered with a special varnish for greater safety.

The board is responsible for the following automation capabilities:

• Automatic closing. The gate will close itself after the set time.
• Reverse engagement after exceeding a preset effort. If the gate hits any obstacle and the motor is overloaded, the drive will begin to move the leaf in the opposite direction.
• Wicket mode. You can stop and fix the gate, leaving any width for passage or passage.
• Start with increased effort. For the first two seconds, the drive operates with increased power in order to move the gate without any problems.

Flush-mounted receiver

This electronic element built into the control board. The receiver receives signals from the remote control with a frequency of 433 MHz.

For signal transmission, you can register up to 60 remotes.

Rack

It is attached to the bottom pipe of the gate frame and moves them by receiving torque from the outer gear of the drive, translating it into a forward motion.

The rail is made of galvanized steel and can last a long time.

The length of the rail must correspond to the length of the sash (+ 1m), therefore it is supplied in one meter lengths.

Remote control

DOORHAN offers two series of remote controls:

• Transmitter Series
• TW series

Transmitter Series:

Transmitter-2- with it you can control two automatic devices(for example, home gate automation and parking gates).

Transmitter-4 and Transmitter Premium- these models of remotes are capable of controlling four automatic devices

TW series:

TW1- single-channel remote control. Can control one automatic device.

TW2- two-channel remote control. Can control two automatic devices.

TW15- fifteen channel console. It can control 15 automatic devices.

Magnetic limit switches

These elements are designed to stop the drive when the gate is opened or closed as much as possible.

Magnets with special brackets are attached to the edges of the rack, and a reed switch is installed inside the drive.

When the magnet is opposite the actuator, its field acts on the reed switch, which breaks the circuit, stopping the motor.

If we compare a magnetic system with a mechanical one, it should be noted that it is more expensive, but does not fail in winter period, as is often the case with mechanics.

The fact is that a mechanical system in frost can freeze the spring on the drive to one of the switches, and the automation cannot be turned on, because the control unit will assume that the mechanical switch acts on the spring. Therefore, this node will have to be warmed up.

If there is snow on the surface of the toothed rack, then when the gate moves, the spring can rake it up until it is enough for it to bend back and turn off the automation.

In this case, you will have to clean the rack with a broom.

Over time, the metal spring can rust from atmospheric cages and break, as a result of which the gate cannot stop.

Photocell safety

These elements are needed to avoid a possible collision of the gate with an obstacle - they identify it in advance.

The receiver and transmitter are attached to poles or mounted on racks, between which an infrared ray is formed, breaking it off by an obstacle, will serve as a signal to stop the gate and direct it in the opposite direction.

When installing photocells on the posts, the obstacle will be detected earlier than their attachment to the posts, because they are located at some distance from the gate.

Doorhan has three models of photocells:

• Photocell-N
• Photocell-R
• Photocell-W

Technical characteristics of Photocell photocells

Photocell-N scatter an infrared beam at a distance of up to 20 meters at an angle of 7 °, so there is no need to install them in a strict horizon in relation to each other.

Photocell-R can be installed on different levels, and correct the elevation using the turntables.

Photocel l - the power supply is carried out by batteries, so there is no need to conduct wiring to them.

Signal lamp

It accompanies the movement of the gate with its flashing light signal. This safety element is especially useful in poor visibility.

Doorhan offers two lamp models:

• Lamp-LED

Model Lamp Comes with a built-in antenna to extend the range of the remote control.

Model Lamp-LED has LED elements that are durable and significantly reduce the power consumption of the lamp.

Indicator light specifications

Buying automation from us

Buying automation from our company, you get:

• The ability to test our recommended drive for a year. This means that during this time you use the equipment and can return it, if you do not like something in it, we will refund your money.
• Choice of how to pay for the order - payment can be upon receipt of the equipment or prepayment
• Guaranteed service maintenance equipment recommended for purchase by our specialists throughout the entire service life.