Ceramic tiles are quite fragile finishing material. What to do if it becomes necessary to cut through it without spoiling the appearance. But it is precisely with a similar problem that we often encounter when installing tile coatings. Below we will tell you how to drill a hole in a tile than to make a hole.

Possible difficulties

The main difficulty lies in the fragility of the material structure. With a significant point mechanical impact, it is destroyed, chips and cracks are formed. This is true for all types of ceramic products. That is why you need to know how to properly drill a hole in a ceramic tile without its uncontrolled deformation.

During drilling, there is a significant increase in temperature in a certain area of ​​the product. This entails a change in operational and technical qualities. One of the problems lies in the structure of the decor. It consists of a ceramic base and a layer of glaze. The second is much harder and prone to destruction with a sharp increase in external pressure.

Before cutting a round hole in a ceramic tile, it is recommended to get acquainted with the most common mistakes:

• The wrong tool. This applies to the cutting part, which should gradually destroy the glaze layer, and then the ceramic base;
• The working conditions do not meet the standards. The tile must be on a solid base. It doesn't matter if it's horizontal or vertical;
• Excess load. The selected drilling technique should not involve pressure, but ceramic cutting. Otherwise, the likelihood of chipping increases.

Given these nuances, you can choose several ways to form holes of various shapes and sizes. First you need to determine the thickness of the tile and, according to this indicator, choose the best tool.

If the processing of the decorative material is carried out after the final stop, cracks may appear on the inside. In the future, a small blow will be enough, which will lead to the final loss of appearance.

Required tool

The correct selection of tools is one of the basic principles for carrying out this kind of work. At the first stage, it is necessary to determine the size of the holes, their shape and number. To perform a large amount of work, a cutting tool is required that will retain its original qualities after long-term operation. Therefore, it is recommended to purchase consumables designed for this operation.

Drill

Here they proceed from certain restrictions that the fragility of the tile imposes on the tool. The latter requires particularly careful handling, so the drill must be without an impact mechanism, or at least it must be turned off. Work is carried out at low speed, because at a low speed, the drill will have little play and vibration.

• an electric drill operating at minimum speed;
• screwdriver: either a cordless type, providing the highest speed of 800-1000 rpm, or a low-speed one that operates on mains voltage.

Drill

Cutting occurs due to the friction of the abrasives.

• To work with glass and tiles, special drills are used. The special sharpness and spear shape allow you to do the job without going into details, how to cut a hole in a ceramic tile.
• If these are not at hand, they can be replaced with well-known Pobedit drills. We only clarify that the tool needs to be sharpened as much as possible.
• For hoods and sockets, pipes or under the toilet, diamond crowns of the appropriate diameter are usually selected. The minimum possible is 5 mm.

• If we are talking about how to make a round hole in a ceramic tile of different diameters in its center, a ballerina will be an excellent solution. Outwardly, it resembles a compass. With its tip rest against the center and adjust the distance between it and the cutter in accordance with the required diameter. Ballerina can drill the wrong tile.
• Another popular tool is a circular drill (saw). They are very easy to use. One element takes about 5-6 minutes.
• If you need to cut a lot of different elements, the jig will facilitate the work. This is a thick plate on which round cuts of different diameters are made. It serves as a kind of stencil.

Some nuances of using tools

During the cutting process, neither the drill nor the tile itself should overheat. Otherwise, cracks will pass through the upper layer of the material, due to which it may crack. The surface to be treated is cooled by periodically pouring water over it.

It is very important to press the drill correctly. The pressure is supposed to be not too weak, otherwise it will simply not be possible to cut anything, nor too strong so as not to break the tile. It is necessary to develop the optimal degree of pressure on the tool.

When drilling tiles, it is necessary to exclude the reverse mode. The drill rotates clockwise at low speed. Otherwise, the material will begin to crack.

If you do not know how to drill a hole in the tile seam, then the process may end with the “loss” of the tile. Pay attention to the location of the center of the hole: its place is the middle of the seam. If you start drilling near the seam, then usually the drill slips into it. As you know, there is no protective layer on the edge of the tile, so it is likely that a chip will form.

Cut holes on the tile correctly

Before drilling a hole in the tile, make marks with a contrasting marker. To avoid slipping of the drill from the smooth surface of the tile, the drilling site is glued with a plaster or paper tape.

If it is supposed to use a conductor, it is brought to the mark with a slot suitable in diameter and fixed.

The drill must be positioned at right angles to the surface of the tile. To begin with, the drill is turned on at minimum speed with the smallest pressure. After the drill has gone deep enough, you can switch to the average speed of the power tool. But even then, drilling is performed carefully, without undue haste.

Many craftsmen, before drilling a tile, pierce a small hole in the marked place with a kernet. Then the spear-shaped drill can simply be inserted there, and at the same time it will not have any play in the groove.

If during the repair work it is necessary to drill a part of the base, then the process is carried out in two stages. The first step, using the appropriate tool, is to drill through the tile. Then, the drill is replaced in the drill for a specific surface and, if necessary, for example, for concrete, the impact mode of the drill is turned on or a hammer drill is used.

How to drill a hole in a ceramic tile for an outlet

Of course, it is easier to cut holes with a small diameter. Along the way, it can be slightly expanded by repeating the operation with a larger diameter drill. And how to cut a round hole in a large diameter ceramic tile? There are two possible options - use:

• cutting crowns made of hard alloys with diamond coating. This is a rather expensive tool, so you need to think about how justified it is to purchase it. The crowns cannot be overheated, therefore, in the process of work, they are moistened with water, and they must work at low speeds of the drill.
• For single works, you can choose a more affordable option. Instead of diamond coating, there are victorious teeth. The tool is produced with different diameters, up to 15 cm. This tool requires extremely careful handling. Unfortunately, the edges are uneven anyway. The obvious disadvantage of crowns with teeth is their fragility, they are able to provide only about 20 cut elements.

If special tools are not at hand, a large hole can be obtained as follows:

• mark a circle of the desired diameter on the tile;
• around the circumference, holes Ø 4–5 mm are drilled tightly to each other;
• gently squeeze or knock out the middle;
• the remaining irregularities are removed with pliers and the edges are sanded with sandpaper.

• It will be useful for beginners to practice on unnecessary pieces of tile to begin with.
• Check the tiles for possible voids underneath. If a dull sound is heard when tapping, you can start cutting a hole without the risk of breaking it.
• Keep in mind that when making holes around the edge or corners of a tile, there is a high chance of cracking.
• If the chips on the edges are small, they are cleaned with sandpaper or covered with a decorative ring.
• In the process of work, they periodically stop. These pauses are used to cool the treated surface with water.
• When working with the "ballerina" you need to avoid fluctuations of the drill in the horizontal plane. To do this, you can install a special tripod used to fix the tiles.

Safety goggles when drilling are a necessary precaution.

In conclusion, we bring to your attention a video on how to cut a hole in a tile using a drill with a victorious tip.

When tiling any surface, the master is always faced with the need to make holes in the ceramic tile for a pipe, an electrical outlet. Holes can be divided into internal, located inside the perimeter of the tile, and external, which extend beyond the tile. Also, in shape, they are divided into radius and rectangular. The way to cut a hole in a tile for a toilet, pipe or electrical outlet depends on its shape and location on the surface of the tile.

Using a grinder

The grinder is a versatile multi-purpose tool that is in the arsenal of every home master. It can be used to cut tiles instead of a tile cutter, which is considered a special tool and not every master has it. To work on the grinder, a metal diamond wheel is installed for dry cutting.

Bulgarian with a circle and discs on stone

The peculiarity of the grinder is that it only performs a straight cut. Therefore, an angle grinder can easily make rectangular holes or make a large cut with a radius shape if the contour arc has a slight bend. A smooth arc or a perfectly round hole will not work right away. First, mark the contour of the radius cut and draw a lot of chords. An inscribed polygon should appear inside the outline. After marking, several cuts are made along the line of chords, after which the contour is finalized with sandpaper.

Important! The tool must be equipped with a protective cover. It is necessary to work with gloves and goggles.

In this case, the grinder does not perform a translational cut, but the tile is cut pointwise from the front side along the markings. Thus, if you plan to cut a round hole, you need to take a diamond wheel as small as possible. The larger the hole diameter, the more accurate the cut will be. The chords along the radius contour will be short, and the cut will be as close as possible to the radius and it will take less work with a round bar with sandpaper to refine the edge.

Work as a grinder

This method works well with tiles. To make radius holes in porcelain stoneware, it is better to use the special tools described below.

Video of the wizard:

Using a jigsaw

A jigsaw is also available to most craftsmen, but it provides more options for curly cutting ceramics. To do this, insert a diamond file into the tool and you can cut a hole in a tile of any shape. To cut the internal holes, you will need a drill with a thin diamond drill bit. They drill a hole on the inside of the contour. A jigsaw file is inserted into it.

Jigsaw cutting

Work with glass cutter and pliers

Manually, without using a power tool, you can make a straight or radius cut for a pipe or outlet from the edge of the tile.

Breaking off with pliers

In addition to the glass cutter and pliers, you will need a straight or round bar with fine sandpaper. The work is done like this:

• Using a marker on the front side, the outline of the future cutout is marked.
• Before cutting a hole, it is recommended to pre-soak the tile in water. This will reduce the risk of splitting.
• After that, a cut is made with a glass cutter along the applied line. To make the furrow deep, it is necessary to apply sufficient force. In this case, you must not overdo it and not split the tile.
• In order for the glaze to completely split along the cut line, the tile is tapped from the back.
• Then, with the help of pliers or special tongs, they bite off a piece of tile, as if biting into it. Gradually, reaching the intended line, the tile will break off along the cut contour.

With this method, it is possible to obtain lines of any configuration, but there will always be small notches on the edge. They need to be removed with sandpaper.

drilling

You can drill small holes (up to 15-20 mm) using a drill by inserting a conical or spiral drill of the appropriate diameter into it.

Drill with cone drill

Drilling is convenient if the tile is already glued. But usually a hole must be drilled before the tile is glued in order to bring the wire into it or put it on the pipe. Therefore, the tile must be well fixed on a flat surface. Drywall or chipboard sheet is used as a substrate. To reduce the risk of breaking the ceramic during drilling, it must be wetted. It is recommended to fill the slats on chipboard to make a box. The rails are glued with silicone. A tile is placed in a box and filled with water. They drill ceramics right in this box. Water will soften the tile, there will be no internal stress in it, and the drill will be constantly cooled.

The technology for performing drilling in tiles is as follows:

• The first problem is that at the first revolutions of the drill, the drill slides along the smooth surface of the tile. An adhesive tape will come to the rescue, which is glued at the place of drilling.
• Mark the drilling point. It should be on duct tape.
• Drilling begins with a slow speed of the drill, so that the drill does not float on the glaze from a jerk and does not make a scratch.
• After the drill has caught on the tile, the drilling site is moistened with water. During the work of the drill, it is necessary to ensure that the workplace always remains wet.

Using a drill, you can make a hole of large diameter under the sewer pipe. But this method can be used when one or two holes need to be made, since the process is laborious and the quality leaves much to be desired.

Contour drilling

To do this, a lot of holes are drilled along the contour of the cutout with a thin drill. Thus, a perforated contour is obtained. After completion, the inside of the hole is knocked out, the remnants of the teeth are cleaned with pliers and leveled with sandpaper.

Drilling with crown and ballerina

If you need to cut a circle of any diameter with high quality and accuracy, professional tile drilling tools will come to the rescue. These include diamond-coated crowns and ballerinas with victorious incisors.

It is easier to work with a diamond crown, since it is a cylinder of a certain diameter with a cutting diamond edge. To center the crown in the center of the cylinder, a conventional pobedit drill is located.

The ballerina is a conventional drill, which has one or two L-shaped pins with a cutter at the end. The pins are attached with a clamp. By pulling out the pin, the desired diameter is set. This is the advantage of the nozzle over diamond crowns, which have a fixed diameter.

ballerina

Despite the fact that this tool is the simplest and most accessible, some skill is needed when working with it:

• Models with one incisor are more durable, but during operation such a ballerina becomes an eccentric, which leads to vibration.
• Models with two cutters are less durable, it is difficult to set both cutters to the same radius. Because of this, the tool cuts two circles, making a double cut.
• When working, it is necessary to maintain a right angle between the axis of the drill and the surface of the tile, otherwise the ballerina will begin to burrow from one side of the circle. In order to maintain this angle constantly, they produce ballerinas with a plastic basket. It performs the function of a control stop and will be able to help the master maintain the angle.

When working as a ballerina, double-sided drilling is performed. First, a protruding drill makes a hole in the ceramic tile. As the drill deepens, the cutter begins to cut through the glaze. Having cut through the glaze, continue drilling from the back side.

Crown

Crowns are sold in sets for standard sizes. Before working with a crown, it is first necessary to drill a central hole into which the crown drill is inserted with a conventional drill.

Video of using the crown:

Modern plumbing is equipped with decorative facing washers on the pipe, and sockets have linings that can block the hole cut by hand or grinder. Therefore, it is not always necessary to cut an even circle, sometimes you can do without special tools.

During the repair process, the need repeatedly arises to make a hole in the tile for an outlet or, for example, a pipe. Moreover, such a need may arise both during the installation process and after installation. Consider how to act in both situations and what tools to use.

During facing work, you can not do without drilling tiles

Most often, making a hole in the tile is required at the laying stage. Until the tile is fixed on the surface, the easiest way to do this is with a grinder. This tool will come in handy more than once during the lining of the floor and walls. It is suitable for curly cutting along the edge of the tile.

How to make a hole in a tile with a grinder:

1. Mark the outlines.
2. Take a diamond blade for dry cutting.
3. Start cutting from a comfortable edge. Move the instrument smoothly away from you. Hold the tile with your hand, do not forget to protect your fingers.
4. If the work area is not too comfortable, stop in the middle and bring the grinder from the other end. However, there is a risk of divergence of cut lines.

You need to work on the front side of the tile to avoid chipping.

A diamond blade is used to cut tiles.

Using a jigsaw

This tool allows you to cut out any shape both from the edge and in the center of the tile. True, in the latter case, you need a drill to make the initial hole.

How to cut ceramic tiles with a jigsaw:

1. On the front side, draw the outlines.
2. If the processing area is adjacent to the edge, start cutting.
3. To make a hole in the center, use a drill to pre-drill a small hole. Thread the cutting thread through it and place the jigsaw on the border of the cutout.
4. Slowly guide the tool according to the markup. Step back from the line a little inward so as not to cut out the excess.

The necessary holes are made in the tile in advance - before laying

Handmade

If you need to make a small cut on the edge, and there is no jigsaw available, there is an alternative way. You will need a glass cutter and tongs or pliers. What is the essence of the process:

1. Mark the contours of the future hole on the tile.
2. To soften the material, soak it briefly in warm water.
3. Take the glass cutter and, without lifting the roller from the surface, draw a line according to the marked markings. Apply sufficient pressure to create a furrow, but do not damage the tile, especially if it is a glossy one.
4. Tap along the cut line to deepen the furrow.
5. Using tongs, break off in small pieces until all excess is removed and an even outline remains.
6. If there are small nicks, sand the edges with fine grit sandpaper.

Hole drilling

If the tile is already laid, you will need a drill. When working with ceramic tiles, special cone-shaped drills or ordinary spiral drills are used.

Exit for engineering communications

How to make a hole with a simple drill:

1. Since the surface of the ceramic tile is quite slippery and it is very difficult to keep the tool in one position, cover the area being worked out with masking tape. It will protect the tile from scratches, prevent chips and slipping of the nozzle.
2. Mark with a dot the place to drill the hole.
3. Start work slowly.
4. To prevent the drill from overheating, periodically moisten it with water. Spray the tile itself as well, but only after you are deep enough so that the tool does not slip off.

If you want to make a large hole, after drilling a small hole, use a thicker drill. Increase the diameter gradually, so the risk of chipping is minimized.

Another way: make several holes along the inner contour of the future hole with a thin drill. Then carefully knock out the center and grind the teeth with sandpaper.

Special drill bits

There are specialized tools designed to work with tiles that allow you to cut a hole of large diameter. One of them is a ballerina. It is a drill with an additional cutting element.

Special nozzle for a drill

How to cut a round hole in a tile using a ballerina:

1. Make a small indentation exactly in the middle in any way.
2. Install the ballerina on the drill and fix it in the hole with the central drill.
3. Begin to deepen slowly. The side elements will begin to scratch the tile, outlining a circle, like a compass.
4. When half the work is done, turn the tile over and do the same on the back until the center falls out.

Another type of nozzle is a diamond-coated crown. Its diameter is selected for a specific size.

How to make a hole in a tile with a crown:

1. Apply masking tape to ceramic tiles.
2. Outline the hole.
3. Attach a drill and start to go deep at slow speeds.
4. Moisten the nozzle with water to prevent overheating.

When purchasing drills for a drill, pay attention to their price and quality. A good job can only be done with a good tool.

02-07-2015

How to cut a hole in a tile? Ceramic tiles are given a significant place in the design of walls, floors in homes and public institutions. She is often finished with sanitary rooms, rooms with bathrooms, landings and much more. The tile is a strong and decorating material for any room, it is practical, easy to use, does not require much maintenance, is not afraid of high humidity, does not change its qualities under the influence of adverse external conditions. In addition, the tile is able to withstand maximum loads on its surface.

Features of such a process, tools

When renovating your home, sometimes you have to make holes in the tiles. The matter is not entirely simple. As a rule, you need to make a cutout under the pipe, outlet, faucet, in the corner areas of the sink. The whole difficulty lies in the fact that inherently solid ceramic tile cracks or simply breaks as a result of a change in its integrity. And often you need to make a hole in the tile of the desired size and configuration. Many non-professionals feel awkward and confused with such a task. To avoid omissions and unnecessary questions, you should know some of the nuances of working with this fragile material.

The question of how to cut a hole in a tile worries many craftsmen. Moreover, the use of conventional tools is unlikely to help. To solve this problem, you can use a number of construction devices: a ballerina, a diamond-coated drill on a crown, a hole saw. The problem of how to cut a hole will be solved in the article below.

Before starting construction manipulations with tiles, it must be prepared. First of all, you need to make the necessary markup. It is done on the front side with a special marker.

Then the tile is fixed on a straight and strong base. Such a surface is a sheet of drywall, chipboard. The wetted tile will not generate dust during the work, it will not crumble or crack.

Using a thin drill during work, many holes are made in the ceramic tile at the same time, and then, using pliers, you can safely break the hole to the desired size. Holes should be made as close to each other as possible, this will help to make a break carefully, achieving smooth edges.

Back to index

Drill with diamond-coated bits

This type of power tool helps to make a hole in ceramic tiles by submerging the tile under water or pouring a small amount of it on the drilling point. To carry out the work, you should select the required size of the diamond crown and fix it on the base of the device.

To avoid errors at the drilling site, a mark is applied to the tile, which can be made with a glass cutter. During work, as a rule, the glaze is removed first, and then the coating of the ceramic tile.

We note an important feature: drilling should be done slowly, without pressing the handle of the tool, without hurrying. It is then necessary to ensure that moisture does not get into the housing of the electrical appliance. Making holes in the tile without the use of water will not work, the tile can quickly crack.

The use of a high-quality diamond crown in the work will ensure its reliability and hardness.

And this is very important when drilling large diameter holes. Such a tool will help to make recesses, holes not only in the tile, but also in the concrete base.

Back to index

Ballerina for round holes

This tool is a round drill. It is used for drilling holes in ceramic tiles, and these holes can be of any size. This is the peculiarity of this device.

Its incisors are set by hand. The only, not entirely convenient nuance is the uneven edges after work, which have to be further processed.

The drilling method is similar to the previous example. A drill treated with water will cool, and the resistance of the tile will decrease.

Back to index

Hole saw: tool application

You can make even round holes using this kind of saw with a carbide tip. This is a special power tool that can slowly but thoroughly perform the work assigned to it. Holes in tiles made in this way will look flawless. Before carrying out work, the hole saw should be prepared. To do this, the drill located in the center should be thoroughly fixed in the drill using a chuck.

Pay attention to this pattern: if the ceramic tile is well fixed, then you can make holes in it in a dry way.

If there is no fastener, it needs to be wetted with water. The whole wisdom of this type of saw is in the intense heating of the tile during operation, the appearance of dust, the tile quickly breaks. The use of water will help cool the tile, thereby maintaining its integrity, including increasing the operating time of this power tool.

One of the nuances of using a hole saw is the likelihood of water penetrating into the body of the device. You can secure the tool by putting batteries in the drill and installing a saw in it. But, of course, long work will not work, because batteries have a limited supply of energy. He doesn't have enough power either.

Also, experts recommend using an outlet with grounding or a special mechanism that can protect the saw and prevent it from becoming inoperative. The residual current device will quickly detect a short circuit and disconnect the device from the network.

For better fixation of ceramic tiles during work, it should be securely fastened. To do this, you can make a plywood box, the corners of which will be insulated. The water poured into such a container will ensure the integrity of the tile.

The tile is lowered into the liquid, then the drill should be fixed in the desired position. Then you can get to work. So that the surface of the tile does not get cracked and does not crumble, you do not need to press hard on the drill during operation.

Having tiled a kitchen or bathroom room, the tenants face the question - how to make a hole in the tile to hang a mirror, hooks, a shower holder or wall cabinets without damaging it.

Indeed, the question is not easy, since the tile can crack or even break into several pieces. And the need to drill a hole in the tile still remains, so it is necessary to find an acceptable and safe way to drill ceramic tiles.

The structure of ceramic tiles

Clay is the main component of ceramic tiles. It is fired and covered with glaze, which includes glass. Accordingly, the tool chosen for drilling must overcome glass and fired clay equally well.

Tools for the job

The question of choosing an electric tool for drilling tiles is simple:

1. Electric drill;
2. Perforator with drilling mode (non-impact mode);

1. Powerful screwdriver.

A more responsible process is selection. A conventional drill for concrete or metal is not suitable for such work.

This requires a specialized tool, originally designed for drilling tiles:

1. A drill with a spear-shaped tip (indicated by symbols a and b in the figure);
2. Crown (in);

1. Carbide drills for concrete (d) with abrasive coating (with reservation).

Caution: The use of drills for concrete is allowed only in cases where there is simply no other tool.
A hole in the tile can be drilled with them, but this must be done with extreme caution.

Depending on the tasks, one or another tool is chosen:

1. holes with a diameter of up to 12 mm for mounting mounted modules are obtained using a drill with a spear-shaped tip;
2. holes of large diameter, for example, for sockets, pipes, etc., are obtained using.

Tip: All other attempts to drill a hole in the tiles already laid on the walls very often end in damage to them.
Therefore, the most correct option is to purchase a high-quality drill or bit for ceramics, especially since they are much lower in cost than the cost of replacing a damaged tile.

There are also other tools for drilling large holes:

1. Ballerina (in the form of a nozzle for a drill with a spear-shaped tip);
2. Universal hole saw with diamond coating (it should be used at low speeds with the addition of water at the point of drilling).

Drilling process

Many are interested in the question: when and how to make a hole in the tile in order to get a high-quality result.

There are 2 drilling methods:

1. Before laying tiles on the surface of the floor or wall;

1. After laying and complete drying of the adhesive solution.

Holes in tiles before laying

If you have to make a hole in the tile for the outlet of the water supply, for example, under:

1. Faucet in bathroom;
2. Place of connection of the heated towel rail;

1. The outlet of the drain siphon under the washbasin;

and the tile has not yet been laid, it is worth doing this work before laying it. This process is more complicated, since the tile is loose, which means that it may be damaged during operation. But in this way you can achieve a high result.

Moreover, it is completely possible to cut geometric shapes in the tile, although for this you will need a hacksaw or a jigsaw with metal blades.

If you want to make a standard round hole, then the algorithm will be as follows:

1. We lay the tiles with the applied drilling point on a solid base;
2. We punch the drilling point;
3. We begin to drill the tile, trying not to raise the rotation speed above 1000 rpm;
4. After passing the layer of glaze, you can increase the rotation speed;

1. The edges of the hole, if necessary, are processed with a needle file to remove irregularities and small chips of the glaze.

After that, the tile is tried on at the installation site, and if the hole turned out to be correct, the work comes down to laying it on the surface.

Holes in tiles laid on walls or floors

Where to start and how to make a hole in the tile, which is already laid on the surface of the walls, in order to prevent its destruction, few homeowners know. You need to start with the fact that you need to accurately determine the place of drilling and designate it graphically (using a marker or pencil).

Then you need:

1. Pick up a drill with a spear-shaped tip or a core for notches;
2. Set to the designated point;
3. Lightly hitting it with a hammer, pinch the place of the future drilling so that the drill does not jump off during the drilling process;
4. Install the drill in the chuck of the electric drill;
5. Install tools perpendicular to the tile and start the drilling process, making sure that the drill does not slip and does not leave scratches on the tile;
6. After passing through a layer of glaze and clay, we stop the process and change the drill to another one (for example, for concrete, in order to save the resource of the tile drill);
7. Further drilling allows shock mode, for example, with a puncher;

1. Having reached the desired depth, we clean the hole from the remnants of materials and install a fastener in it.

Very often, apartment owners need additional electrical outlets on tiled walls. If the holes in them were not made in the process of laying the tiles, then the process of drilling them in place is ahead. However, the ballerina can only drill through the tile, and the coated bit does not have a center drill.

In such a situation, a special device called a stencil will help. It can be purchased at hardware stores, and it will greatly facilitate the work.

The order of drilling will be the same:

1. We put the center point of the future hole on the tile;
2. Install the stencil on top;
3. Holding it with your hand, we take an electric drill with a crown for drilling ceramics;
4. We start drilling at low speed;
5. After passing the glaze layer, increase the speed;
6. Depending on the materials under the tile (concrete, brick, wood), we decide on further drilling of the hole - either we replace it with another tool, or we continue to drill further;

1. Having reached the required depth, stop drilling and clean the hole from the remnants of materials.

Conclusions: armed with power tools and acquiring high-quality equipment, it will be easy and simple for you to drill a hole in the right place and the right diameter, without fear of damaging the tiles laid on the walls.