How to make a whistle out of wood with your own hands, what you need to know and be able to do.

Material selection:
A plant hollow reed trunk is suitable for this product,

reeds or a tube made of wood (you can use food-grade plastic).

Detailing:
tube
inlet cylinder
tone control plug

TUBE

Made of wood. O.D- twelve millimeters. The wall thickness is two millimeters. Length - one hundred and twenty. On the side of the inlet channel, at an angle of thirty degrees, there is a cut. There is a groove on top for air outlet. The surface is decorated.

CYLINDER

Made of wood. Its diameter is eight millimeters.

At the top there is a cut at an angle of five degrees towards the entrance of the tube. At the bottom there is a cut identical to the cut in the tube.

PLUG

Made of wood. Its diameter is eight millimeters. Length - eighty.

Assembly order
1. Coat the cylinder with glue and insert it into the tube from the cut side.
2. Insert the plug into the tube with reverse side.
3. Use the depth of the plug to select the sound tone (the deeper, the finer the sound)
4. Cut off the excess part of the plug.
5. Coat the remaining part of the plug with glue and insert it into the tube.

Reference: if the length of the tube is increased to 280 (mm); make six holes in turn on the surface of the groove, from the edge of the product (each of which has its own tonality - the wider and further from the groove, the higher the note) with a step of 20 (mm); make one hole on the back side of the groove surface, from the edge of the product, at a distance of 140 (mm); we get a pipe.

We invite you to watch the video clip: “How to make a whistle from wood,” where a product of a different design is presented.

Homemade whistle – funny toy with cheerful sonorous trills, which can be made from paper, tree branches, tin cans, plastic stoppers. We have collected the most interesting and proven methods for making a whistle - choose the material and follow our advice.

How to make a whistle from wood

For the whistling mechanism, a freshly cut even twig of willow or hazel, 15 cm long, 2 cm in diameter, is suitable. You will also need sharp knife and some free time.

• Cut vertically one end of the twig, and make a circular notch on the second.

• On one side of the stick, closer to the edge, cut off the bark in the form English letter– D. Tap the workpiece with a knife so that the bark comes off, then press it with your fingers and it will move off the base itself.

• From the bare rod, cut off a small rectangle at the location of the ring marking and cut off part of the wood from it - the gap for the whistle.

• Insert the resulting part into the bark case with the cut side up. Stick the remaining piece of twig into bottom part whistles.

• Blow into the upper hole of the tube, and with your hand, alternately raise and lower the bushing stick, adjusting the sound range. When the timbre suits you, shorten the craft.

Tip: when the bark dries, the whistle stops whistling. Soak it in water for half an hour and it will work again.

Your child liked your gift so much that he whistles as loud as he can all day long? Build a pipe using the same principle, doubling the length of the product and cutting several round holes, and listening to the music going on will be much more enjoyable.

How to make a whistle out of paper

Even a kindergartener can make a paper whistle. True, the thing will be short-lived, but it will whistle a lot.

• Take a sheet of office paper and cut one third of it horizontally.
• Set aside 1.5 cm to the right and left of the wide part, draw lines and crease them.
• Fold the figure in half so that the strips folded on the sides go on outside. Cut two triangles in the center of the fold.
• Place your lips on one triangle and blow into it, then blow into the second hole. Of course, the sounds that come out don’t resemble a whistle; rather, it looks like the purring of a cartoon mammoth looking for its mother, but the kids will like it, that’s for sure.

How to make a mini whistle

A whistle resembling a hunting call can be cut from a tin coffee or beer can. Prepare: scissors, pliers, electrical tape, nails. See the craft drawing below.

• Cut a piece of tin from a can, and from it - two rectangles, measuring 20 x 40 mm. Mark them with a nail and make them according to the template.

• Bend the wings on both sides of the first piece using a folding meter or fingers to create a 0.5 mm hole for air to pass through.

• Insert a second plate made of tin into the slot. Crimp the structure with pliers and secure with insulating tape.

• Bend the tab using a round pin.

• Close the side exits of the tongue with your fingers and whistle. Do you think the whistle is too small? Adjust the model to the desired size by increasing its parameters proportionally.

Instead of a conclusion: all the whistles presented in our selection make piercingly loud sounds, so it is better to practice whistling in nature, and not in a city apartment.

The most valuable gift is a gift made with your own hands! To make it interesting, original, unusual, you won’t need much time and effort! The main thing is desire. If you have it, then this article is for you.

Whistle- an excellent, unusual gift for both any child and every adult. The task is not the easiest to make the whistle work and whistle the first time. This will require your patience and attentiveness.

How to make a whistle with your own hands?

You will get a very beautiful and interesting toy if you make a whistle from wood! It will turn out natural, natural and alive! Will bring joy and pleasure to its owner. When choosing a tree for a future whistle, they usually give preference to willow or linden, since you can easily peel the rod without spoiling it at all.

How to make a whistle from a tree?

1. Be careful when choosing future basis for the whistle. You need to choose a beautiful rod, the thickness of which will be about the thickness of a finger, about 12 millimeters, and cut it off. It is very important to choose a twig with a smooth, beautiful peel, because this is the basis of the future whistle. The length of the branch can be from 5 to 7 centimeters.

2. After you have chosen the desired rod, you need to trim it from all kinds of twigs, leaves and small twigs. It is necessary to clean it of this; the rod must be even and smooth. Next, you should trim the edge of the future workpiece.

3. The next step is to make a small wedge-shaped cutout. It should be made quite in-depth. The cut should engage the wood. You need to make such an unusual mark, which will soon be necessary and will help your future creation.

4. The next step is a ring cut. It must be done 4 centimeters from the end of our rod. The bark should be cleared from the rod; this can only be done with a deep cut.

5. You need to tap the rod. To quickly and conveniently tap the rod, you can use the handle of the most common standard knife. It is lightweight and easy to use.

6. A very delicate task - you need to remove the bark. We scroll through the workpiece and carefully remove the bark with a knife. You must definitely succeed!

When you peel the bark, it looks like this:

7. Have you forgotten about the unusual mark we made earlier? Now it’s useful to us! It is necessary to remove small curves of wood. Very important: you need to give it the shape of a strip.

Hello! I think for those who get lost in the forest the whistle is just necessary thing. This article caught my eye.
So, we need a smooth willow rod, 7-10 millimeters thick. Why willow? Because with willow twig- You can remove the bark very easily without damaging it. And this, as we will see later, is very important for us.

In addition, willow is a plant with brittle branches, which means you won’t have to spoil a living plant. It is enough just to take a walk under a willow tree after a fresh breeze to collect a bunch of branches, exactly what we need.

We select a branch with intact and even bark (this is very important condition), if possible, without knots. Now we need to find a flat section of 4-7 centimeters long on this branch. There may be buds in this area (this is common for willow), but under no circumstances should there be any knots.

Now we cut the branch along the border of a flat area. At the other end of the piece we make a circular cut, as shown in Figure 1. The cut should be deep enough and lightly (just lightly) cling to the wood. To make sure that the entire layer of bark is really cut through, you can remove a ring 1-2 millimeters thick.

After this, we begin to lightly “tap” the bark with a small hammer in a circle in all places. Instead of a hammer, you can use the handle of a knife (Figure 2). Instead of tapping, you can also “roll” the twig. This is done so that the bark subsequently peels off the wood more easily.

We make a cutout on the branch, of the same shape as shown in Figure 3. After this, carefully, using rotational movements, we try to remove the bark from the branch without damaging it. There is no need to rush; if the bark does not come off, you need to knock on it again and try again. In the end, it will definitely come off (Figure 4).

Now carefully cut off the “round piece” from the branch remaining without bark with a knife, just along the line of our cutout, as this was done in Figure 5.

Then we cut off the round barrel (Figure 6).

Don’t try to cut it absolutely evenly, it won’t work anyway. Actually, we don’t need that. If the cut turns out to be wedge-shaped, as in our figure - this is only for the better - it will be easier to regulate the sound.

We insert the cut round piece into its original place, cut side up. If our cut is oblique, then we place the bottleneck towards the hole (Figures 7 and 8).

Now, attention. We clamp the open end of the resulting tube and blow into it quite strongly from the side of the round. The result will be a distinct whistle. True, its timbre may not be very beautiful.

No problem, we will adjust it now.

We cut off the remaining end of the stick, insert it into the open end of the tube and move the stick back and forth to select the most pleasant timbre of the whistle (Figure 9). Then we cut off the protruding part of the branch and the whistle is ready! (Figure 10)

Attention! Our whistle makes a pretty loud whistle. Therefore, the best place for exercise is a dacha or country house, but not a city apartment.

And finally, one piece of advice. If you manage to find a willow twig with a sufficiently long section of smooth bark, 10-15 centimeters, then instead of a whistle you can make a simple homemade pipe. It is made in exactly the same way as a whistle, only instead of selecting the timbre of the sound, simply plug the open end with a wooden stopper, and in the remaining space, make 3-4 holes in the bark, so that they can be plugged at the same time with your fingers. By opening one or another hole one by one, we can reproduce the simplest melodies. Of course, our notes will not correspond to the natural scale, but we don’t need it. The main thing is that the melody is pleasant.

I got the article here.

How to make a wooden whistle that fits in your pocket - this complex process, which takes practice, experimentation, and tweaking, but I hope this tutorial will give you all the information on how to make your own sumac pocket whistle.

Materials:

• An even branch of downy sumac (or any other tree with a soft core, such as willow) 7 - 10 cm in length and 1.5 - 2 cm in diameter
• A pair of twigs, peeled of bark, approximately 0.5 cm in diameter

Tool:

• Hand pruner
• Hacksaw for metal
• Small sharp knife
• Drill
• Cue ball 0.5 cm

Safety. This manual covers working with power tools and knives, so work carefully and wear safety equipment.

Step 1: Drill a hole in the sumac

Focusing on the core of the sumac, we drill a 0.5 cm hole through it using a cue ball.
Keep the drill at high speed, but do not push it too hard. This will increase the chances that the wood will not burst during drilling. Try to get the hole as close to the center of the piece of wood as possible. If the cue ball is shorter than the sumac, then drill a hole on the other side as well.

Step 2: Remove the bark from the sumac

Peel the bark off the sumac until you reach the wood. If the sumac is fresh, there will be a thin green layer around the wood that can be easily scraped off with a knife, and sometimes it can be removed simply with your fingers. When using a fresh sumac branch, the bark is easiest to peel off.

Step 3: Cutting the Serif, Part 1

Using a fine-tooth saw, cut through the sumac to half its diameter. This cut should begin approximately 1.5 - 2 cm from one of the ends of the whistle. Saw slowly to ensure the cut is even, straight and precise.

Step 4: Cutting the Serif, Part 2

Measure 1.5 - 2 cm from the previous cut and make a mark in this place. Using a knife, cut the wood towards the cut. The angle of the cut part should be approximately 35 - 45 degrees. Cut the wood carefully so as not to inadvertently cut off the part that comes after the cut.

Step 5: Create the first plug

Trim the first branch, leaving a length of 1 cm. To obtain a branch required diameter, you will have to be patient and make several attempts. This plug should fit very tightly into the end of the whistle. Opposite of where we made the cut.

Be careful when cutting out the cork. After all, working with such small objects requires caution, precision, and the knife must be very sharp.

Step 6: Create a Second Plug

Following the same procedures as in the previous step, create the second plug. It should fit tightly on the side of the sumac where we made the cut.

Once the cork is ready, cut 2/5 off along the long side. This will create a small opening for air when the plug is inserted into the hole and air is blown into the notch.

Step 7: Insert the plugs

Insert the plugs into the corresponding holes so that they are flush with the ends of the whistle. The inner end of the plug inserted from the mouth side should be in line with the notch line.

Step 8: Finishing Touches

Trim the end of the whistle where the lips will be attached. To make it more convenient. I kept the design of this whistle simple by cutting the same amount of wood off the other end and making a single circular cut along the body of the whistle.

Feel free to experiment and come up with ideas. various decorations for the whistle, just don't cut the grooves too deep. Make whistles with in different forms under the lips, also whistles from the branch different lengths will create different tones and pitches.