How to wash off the fungus in the bathroom with folk remedies. Effective remedies for getting rid of mold in the bathroom and methods of prevention

06/08/2017 0 4 616 views

Not everyone knows how to get rid of mold in the bathroom at home, but you need to do it. Mold in the bathroom brings not only aesthetic discomfort, but can also adversely affect the health of the household, especially if the family has children.

Mold is a fungus that grows very quickly in humid conditions. Poor ventilation of the room contributes to the appearance of mold. It can appear on the bathroom itself, walls, sink, floor. You can cope with this problem, the main thing is to know what tools can be used.

Methods for dealing with mold in the bathroom

Mold is a black fungus that spreads easily indoors. Its main danger is that it can cause respiratory tract infection if it enters the lungs. People suffering from asthma are especially susceptible to various complications that can be triggered by mold.

It is quite difficult to completely remove the fungus from the bath, it will require complex measures and, possibly, the use of several antifungal agents. Small particles are found at the seams of the tiles, so this section of the walls should be given special attention. Subject to all of the following recommendations, you can deal with mold in the bathroom forever.

Installation of ventilation or its improvement

So, you have come close to the issue of removing mold from the bathroom, then you should understand that it is not possible to do just one cleaning. Mold is a very caustic fungus that penetrates into various crevices and cracks; it can be removed only with an integrated approach, when a blow to the fungus will be made from different directions.

The first and very important step is to ensure good ventilation in the room. This is what becomes the main cause of mold formation. The bathroom is always very humid and if the room is in this state for a long time and the ambient temperature is within certain limits, namely above 20 degrees, then the chances of fungus formation are almost 100 percent.

A steam room is formed in the room, which is an excellent breeding ground for mold.

If there is no ventilation at all in the bathroom, then it will not be possible to get rid of mold forever, first you need to ensure the possibility of air circulation.

If there is ventilation in the room, but it does not function, then it needs to be cleaned, perhaps it got clogged with dust and dirt over time and now cannot fully fulfill its function.

Troubleshooting plumbing

Once the ventilation is in place, it's time to move on to the next step in fighting mold. Despite the fact that the bath is a place where there is always a lot of water and moisture, it is very important to keep it dry. So, if the tap is leaking, it needs to be repaired or replaced with a new one. Water leaks will cause increased humidity, that is, the mold will come back again and again.

If there is a washing machine in the room, then it is very important that there is no water left in it, as it also becomes a soil for the spread of mold. After each wash, thoroughly wipe the rim of the washing machine if moisture accumulates there periodically.

When the fight against mold lasts for many years, then it can be won only by applying drastic measures. The old bath, sink and tiles will have to be replaced. Small cracks that have formed on them over time have become a place where the fungus continues to multiply. Even after general cleaning, if these problem areas are not addressed, mold will return. The vicious circle will continue and life between the tiles will flourish.

Reducing dampness

If your apartment has low-quality pipes and condensation constantly forms on them, then the previous two steps will not work. It will be possible to completely eliminate the fungus only after the pipe insulation has been improved.

Permanent condensation is one of the reasons for the appearance of mold on the floor, ceiling, walls.

After all the above points, the room will need to be dried very well; an electric heater is suitable for this. Then you can start using various anti-mold products, which you also can't do without.

How can you clean up mold in the bathroom?

Mold is a rather caustic and tenacious fungus; coping with it is not an easy task. When all the technical points have been improved, cleaned and dried, it is time to clean the surfaces from mold with products that can be prepared at home or purchased at a specialized store.

Baking soda

Baking soda can help remove mold from horizontal surfaces.

  1. A small amount of baking soda is poured onto the dirty areas of the bathtub, sink or floor so that it covers a thin layer of mold.
  2. Vinegar is added on top, after the reaction is over and the soda stops foaming, it is removed with soapy water or a cleaning compound.
  3. After removing traces of mold, the bath is rinsed with running water and wiped dry with a soft cloth.

Do not be afraid to clean the joints between the bathroom and the wall with baking soda, it does not leave any marks on the sealant, does not change its color and is absolutely safe.

Table vinegar

The following composition quickly and very effectively deals with mold:

  • water is poured into the container, 2 tablespoons of vinegar, 2 tablespoons of hydrogen peroxide, 1 teaspoon of boric acid are added to it. All ingredients are mixed;
  • using a sponge or rag, wipe the contaminated areas with the prepared composition;
  • after removing all contaminants, the bath is rinsed with running water and wiped dry with a soft clean cloth.

The prepared composition is suitable not only for cleaning the bathtub and walls, it copes well with the fungus that can spread to the curtain or curtain. They are gently wiped with a product and rinsed in running water.

Hydrogen peroxide

Mold is a caustic fungus, but it doesn't always require complex cleaning agents to remove it. If you can't find all of the above remedies in your home at once, then you can use a mixture of only two, which will be almost as effective in fighting the fungus.

  1. Pour warm water into a container, add two tablespoons of hydrogen peroxide to it and mix with the same amount of vinegar. Stir.
  2. Soak a clean cloth or sponge in the prepared solution and apply to the soiled areas. Leave it on for 30-40 minutes. During this time, a chemical reaction should occur that will remove the fungus from the surface.
  3. After the time has elapsed, rinse all areas thoroughly with warm running water and blot with a dry cloth.

Not only does hydrogen peroxide kill the fungus itself, it removes yellowness and brings bathroom surfaces back to life. Allows you to clean the tile, does not spoil it and does not change its color.

Ammonia

When the pollution is extensive, only drastic measures will help to cope with them, but if everything is not so scary in your bathroom, then you can use the following remedy:

  • add two parts of ammonia and two parts of any detergent to four parts of water;
  • the prepared mixture is applied to the contaminated areas and left for 20-30 minutes;
  • after a lapse of time, the applied composition is washed off with warm running water, and the surface is wiped dry with a clean cloth.

Ammonia works well against mold, while it has an antiseptic effect and prevents fungal spores from spreading to other surfaces, exacerbating the problem. An ammonia-based product can be used not only to remove mold, but also as a prophylactic agent to prevent mold formation.

Copper sulfate

When no other product allows you to completely get rid of the mold, you can use copper sulfate, which perfectly eliminates this problem.

It is very important to use copper sulfate on time, to observe safety measures. Do not start cleaning the bathroom without wearing rubber gloves.

  1. In a bucket or bowl, dissolve the copper sulfate in water, in a ratio of 1 to 10. Mix thoroughly.
  2. For application to dirty areas, it is best to use a brush instead of a cloth or sponge. Thoroughly moisten problem areas with cleaning agent and leave for about one hour.
  3. After the time has elapsed, rinse the applied composition with running water, it is advisable to do this several times in order to completely remove traces of the product.
  4. Dry the surfaces with a clean cloth and ventilate the bathroom.

If the contamination was so strong that it was not possible to remove the contamination from the first time, then repeat the procedure by increasing the exposure time.

Boric acid

The following solution will help remove old traces of mold:

  1. Pour 10 liters of clean water into the bucket.
  2. Add 500 g of boric acid, 1 kg of borax and two tablespoons of vinegar. Stir with a wooden stick.
  3. Apply the prepared solution to the contaminated areas with a sponge or spray bottle and leave for several hours.
  4. After the allotted time, wash off the applied composition with clean running water. Dry the surfaces in the bathroom.

To fix the result, repeat the procedure after a few days. Boric acid does not corrode surfaces, so it can be used regularly to clean surfaces from mold. At the same time, it can leave burns on the skin, so do not contact the solution without rubber gloves.

Chlorine

Not every product is capable of dealing with extensive contamination. However, chlorine-based products can do this.

  • Pour water into a container and dilute with chlorine bleach in a 1 to 1 ratio;
  • use a sponge to apply the product to the surface;
  • rub into seams and cracks with a brush;
  • rinse with warm running water, dry and apply sealant to the joints.

Bleach is very toxic, so take care of a face mask and rubber gloves before cleaning. After removing mold, ventilate the area.

Antifungal agents

In apartments with an old renovation, mold often forms in the gaps between the tiles, which is extremely difficult to remove. To do this, the tile joints are sawn, cleaned, and abundantly treated with an antifungal agent. After drying, the seams are rubbed again.

This way of dealing with mold is very cardinal, it is better to regularly clean the room and prevent a large accumulation of mold.

Antifungal agents

If you have tried all kinds of home remedies for getting rid of mold, but it comes back regularly. Then you should contact a specialized store for help. Modern industry produces a wide variety of products that do a good job of dealing with mold, even with a large accumulation of mold.

Having visited a household chemicals store, consult with a specialist, she will have to tell you which product is best to use. Usually, antifungal agents are used to get rid of mold. Before you start using it, read the instructions carefully and strictly follow the indicated recommendations. Do not forget about safety measures, you must wear rubber gloves and a mask.

When choosing a product, make sure that it is designed to remove mold from surfaces, and it is used to prevent it.

Video: how to get rid of mold in the bathroom at home?

How to get rid of black mold in the bathroom?

Some are afraid when they see traces of black mold on the wall and do not know which means to grab. In fact, you can use any of the above tools to remove it.

You can also prepare a special composition:

  1. 4 parts of water, 2 parts of hydrogen peroxide, 1 part of boric acid, 3 parts of vinegar are diluted in a small container.
  2. All ingredients are thoroughly mixed.
  3. Using a sponge, the solution is applied to the contaminated areas and rubbed thoroughly.
  4. After 15-20 minutes after application, it must be washed off with warm running water.
  5. Be sure to wipe the surface dry with a clean, soft cloth.
  6. Ventilate the room and do not use it for 6 hours.

Mold is an insidious fungus, it can arise even in seemingly washing conditions. Regular cleaning does not always allow you to avoid its appearance, but good ventilation will be a good prevention.

Make sure that there is no high humidity in the bathroom for a long time, and that condensation does not settle on the pipes, then you will not have to face the problem of mold.

A good bathroom should not only have expensive fixtures and fittings, but also be clean and well-groomed. Maintaining it in proper condition and order is not so easy, and among the many problems in this matter, the fungus stands out the most. Having appeared, it is able to spoil the appearance of even the most expensive and sophisticated bathroom. But this is only half the trouble - the fungus still poses a serious danger to the health of everyone who lives in an apartment or house. At the same time, it is not easy to get rid of it - microorganisms sometimes show tremendous vitality and resistance to all influences. Therefore, for many owners and housewives, the problem of how to remove the fungus in the bathroom is extremely relevant and important.

Where does the fungus most often appear in the bathroom and how to recognize it

Even in the cleanest and most well-groomed apartment, there is certainly a certain amount of fungal spores in the air in a "canned" state. But this is only until the moment when they do not get into a warm and humid environment, favorable for them. If the conditions are right, mold colonies begin to develop from the spores. Mycologists subdivide them into many genera and even more species. But for a person with only basic knowledge of biology, the difference between different fungi will consist only in their colors, which are shown in the table below.

Table. What can be the fungus in the bathroom.

AppearanceDescription

The most frequent "uninvited guest" of the bathroom. Depending on the specific strain and the degree of development, the color ranges from light gray to jet black. This mold requires high humidity to grow. It includes the genera of the fungi Ulocladium, Penicillium, Aspergillu and Phoma. Black mold is highly pathogenic and poses a serious threat to human health.

Compared to the previous type of mold, it is much less common. The white fungus generally prefers to grow on food and potted plants. In the bathroom, it can be found on the walls, but it is quite rare.

The main victim of these fungi is wood. In the bathrooms of city apartments, they are practically not found, which cannot be said about country houses and cottages built of timber or logs. Blue mold not only impairs the appearance, but also reduces the structural strength of materials. Over time, a tree affected by such a fungus becomes completely unusable and collapses.

It is not difficult to recognize the appearance of mold in the bathroom - it is a bloom of black, gray, blue, brown and, in some cases, white. To the touch (you should only touch the fungus with gloves), it seems fluffy. Most often, mold appears on the seams between the tiles and at the joints of the sink or bathtub with the wall. In especially severe cases, colonies of fungi are located simply on the wall or ceiling in the room. It is not uncommon for mold to be found under the bathtub, or - a dark, warm and humid place is extremely attractive for fungal spores. Microorganisms can also appear under wall cladding that does not adhere tightly to concrete.

In addition to external signs, the fungus can also be recognized by its smell - the bathroom begins to smell of dampness, musty and basement. It is impossible to confuse such a "flavor" with something else.

Important! In some cases, an indirect sign of the presence of fungus in the bathroom is the increased frequency of headaches among residents of an apartment or private house.

Reasons for the appearance of fungus in the bathroom

So you've found mold in your bathroom. Now it is necessary to understand why it appeared there - otherwise the elimination of the fungus will turn into a fight against the consequences, but not the cause.

There are several reasons why mold could develop on tiles or joints between the bathroom and the wall:

  • high humidity;
  • lack of natural light;
  • high room temperature;
  • the presence of hard-to-reach and dark places;
  • problems with air circulation.

Now let's look at the causes of mold in more detail.

First, the fungus needs a moist environment. The bathroom fully meets this requirement - something connected with the use of water is constantly working here (shower, washing machine, sink, and in the combined bathroom - also). Dryness in such a room is extremely rare. In addition, the situation with high humidity can be aggravated by leaking plumbing and water pipes, on which condensation falls.

Secondly, mold does not like direct sunlight. Therefore, the bathrooms of typical high-rise buildings are a very favorable environment for her in this regard - they are not equipped with their own windows, the lighting there is exclusively artificial. Sunlight does not get there, therefore it cannot suppress the activity of mold. For country houses and cottages, the situation is rarely better - there the windows in the bathrooms are also not installed too often.

Third, the fungus needs warmth. The bathroom is a very limited space where you work, and hot water is constantly used. And, as mentioned above, there is no window. Therefore, the temperature in the bathroom is extremely low, which is what molds need.

Fourthly, it is desirable for microorganisms to have secluded and dark places with difficult access, where they can grow, multiply, and then move to visible surfaces unnoticed by the owner of an apartment or cottage. In our case, there are many such places - under the bathroom, behind the washing machine, sink and toilet, floor and ceiling joints with pipes, etc.

Fifthly, the absence of air circulation in the room is desirable for the fungus. And if the ventilation in the bathroom does not work properly, then over time, in the presence of dampness and heat, mold will certainly appear.

Advice! There is an easy way to check how good or bad the air circulation situation is. Bring a piece of tissue paper or a lighted match to the grate of the ventilation shaft in the bathroom. If the paper or the flame is not "blown away" anywhere, it means that the air circulation in the room is unsatisfactory, it may be necessary to install a forced ventilation system.

Why is the presence of fungus in the bathroom dangerous?

The most obvious problem caused by the appearance of mold in the bathroom is the deterioration of the appearance of the room. As mentioned in the introduction, even an exquisite and expensive finish loses all its beauty when mold appears. And in the most serious cases, removing the fungus will require dismantling the tiles - in fact, you will have to repair the bathroom again.

Mold is a big problem for owners of country houses - in the course of their life, microorganisms gradually decompose some components of the wood. As a result, it not only deteriorates externally, but also loses its strength, and rather quickly - the fungus in this regard is distinguished by its "gluttony". Mold and other materials are not sparing - microorganisms can spoil concrete, brick and even tiles.

But the main danger of fungus in the bathroom is not damage to finishing and building materials, but in creating an immediate threat to the health of all residents of an apartment or cottage. Mold can come into contact with a person in two ways - by contact with the skin and by inhalation of small particles and spores.

These microorganisms, in the course of their life, emit a lot of toxic substances, and the presence of a fungus in the bathroom can lead you or your household to the following diseases:

  • headache;
  • various allergies;
  • asthma;
  • sinusitis;
  • sinusitis;
  • disorders of the digestive system;
  • disruption of the kidneys and liver;
  • joint diseases.

The fungus found in the bathroom will be especially harmful for children, the elderly and those whose bodies are weakened by other diseases, recent surgeries or chemotherapy.

Important! Doctors categorize all ailments and diseases caused by mold and other fungi into a separate category - mycoses.

Removing fungus from tile seams

Most often, mold in the bathroom appears in the form of small colonies of microorganisms that settle on the grout between the tiles. If you notice this in time, then the growth of the problem to something larger can be prevented. We will get rid of a small and shallow focus of the fungus lesion mechanically.

To do this, you will need the following materials and tools:

  • sandpaper or metal brush;
  • rubber spatula;
  • dry grout mixture and container for it;
  • varnish and brush.

Here is the process of removing the fungus from the seams of tiles in the form of step-by-step instructions.

Step 1. Identify the areas affected by microorganisms. If you wish, you can mark next to it with a marker on the tile.

Step 2. Using an emery cloth or metal brush, scrape off the old grout from the joint between the two tiles. Work must also be carried out near the places where the spots of the fungus are located - there may be still invisible colonies of mold that have not yet grown enough.

Step 3. Clean the seam where the old grout was located completely - both from the fungus and from the dust formed during the work with sandpaper. Then treat it with "Whiteness", bake it with a soldering iron or, at least, a regular hair dryer - the high temperature will help "burn out" the remaining mold.

Important! Do not wet the seams with hot water - in this case, its temperature is insufficient, and the very presence of moisture can only help the microorganisms to survive.

Step 4. Dilute the grout mixture. Using a rubber trowel, apply it to the seam between the tiles.

Step 5. When the applied grout is dry, use a brush to cover the seam between the tiles with varnish to deprive the fungus of a surface suitable for existence.

Removing fungus in the bathroom using folk methods

Before the advent of modern household chemicals, the owners of apartments and cottages fought the fungus in the bathroom with the help of available tools, many of which are in any kitchen or in a home medicine cabinet. Therefore, we will give a brief overview of folk methods of dealing with mold.

Vinegar. One of the most common tools that must be in the kitchen. Allows you to cope with small colonies of fungi that have settled on the joints of the tiles, under the mixer or between the bathroom and the wall. The simplest table vinegar without any additives is suitable for removing mold.

Step 1. Pour a small amount of vinegar into a container with a spray bottle or soak a rag with it.

Important! Vinegar, when inhaled, can irritate the mucous membranes - cough, runny nose, watery eyes, but is unlikely to cause general poisoning of the body.

Step 2. Spray the liquid or apply with a rag to the problematic area of ​​the bathroom.

Step 3. Wait 60 minutes for the vinegar to dry.

Step 4. Remove mold residue with a rag or stiff brush.

Step 5. Rinse the lesion of the fungus with water, then wipe dry. Then ventilate the room.

Step 6. Within a month, repeat the procedure on this area of ​​the bathroom weekly - this will prevent the return of the fungus to the previously affected area.

It is a remedy that can be found in almost every home. It copes not only with heavy dirt, but also with the fungus that has settled on the tile or bathroom. Work with "Whiteness" should be done exclusively with rubber gloves.

Step 1. Identify mold-affected areas in your bathroom.

Step 2. Pour a small amount of bleach on horizontal surfaces, lubricate vertical surfaces with a cotton pad or a cloth soaked in "Whiteness".

Step 3. Leave the bathroom for a few hours. If possible, do not use it during this time.

Step 4. Ventilate the room and check the results - "Whiteness" is able to successfully remove small accumulations of fungus. Remove residues and bleach residues, rinse everything with water.

A 3% hydrogen peroxide solution is also a common folk remedy for mold. Apply in the same way as with vinegar and bleach - locate the affected area of ​​the wall or plumbing, process, let the substance dry, then ventilate the area, remove the remaining fungus and rinse everything with water.

Important! Remember that both Whiteness and Hydrogen Peroxide are bleaches. Therefore, some finishing materials from contact with them may lose color.

According to similar principles, some hosts use baking soda and ammonia... In the case of the latter, after application, you should not visit the room for a while - the substance produces a very pungent and unpleasant odor that can cause you a headache. Also, under no circumstances mix ammonia with bleach - as a result of their combination, chlorine is released, which in a gaseous state is dangerous to humans.

A kind of "last chance weapon" in the fight against fungus in the bathroom is creosote- a dark oily liquid made from tar. The main field of application is the treatment of sleepers and other wood products in order to protect them from decay. Dissolve the creosote in alcohol or oil, apply to the affected area of ​​the wall or ceiling, wait for a while and rinse everything very thoroughly with water and detergent. Remember that this substance is toxic, therefore, after processing, it should not remain in the bathroom at all. In addition, work with creosote only in protection - with glasses, a respirator and gloves.

Important! Do not use creosote to remove fungus on wood - it will be absorbed there and will have a toxic effect on you and your household instead of mold removed by it.

Video - Remedy for fungus in the bathroom. Test - experiment

Removing fungus in the bathroom using household chemicals

The modern chemical industry produces a huge amount of fungicide substances that can quickly cope with even serious foci of fungus in the bathroom. The principle of application for most of them is the same - an antifungal agent or its solution is applied to a mold-affected wall, ceiling or plumbing with a spray gun, then a certain time is waited, and then the same area is washed with water.

Below is a list of the most popular and effective household chemicals designed to combat such microorganisms:

  • DALI;
  • MILLKILL
  • Atlas Mykos;
  • SZAVO;
  • Spectrum Fungicide;
  • "Titan Fungicide";
  • Belinka;
  • Mellerud;
  • Astonish.

Important! Before using any household chemicals to remove fungus in the bathroom, carefully read the instructions for use. It is advisable to do this in the store, when choosing a product.

Another very unusual anti-mold agent in the bathroom is an ionizer checker. When activated, it emits smoke containing silver ions. Quickly enough, this smoke fills the entire bathroom, penetrating into the most inaccessible places, disinfecting them and killing the fungus. Use a checker-ionizer as follows.

Step 1. Open the package and take out the checker.

Step 2. If ventilation in the bathroom is carried out forcibly, with a fan, turn it off.

Step 3. Pour some water into the checker box, put it on the floor in the center of the bathroom.

Step 4. As soon as abundant smoke begins to come out of the checker, leave the bathroom and close the door. Tuck the door underneath with a rag if necessary.

Step 5. Wait approximately 90 minutes.

Step 6. Ventilate the room, examine the bathroom. Remove mold residue with a cloth or brush.

Fungus remover prices

fungus remover

If all of the above methods did not have the desired effect, or if mold is removed during the repair process in the bathroom, use the method given in this step-by-step instruction.

Step 1. Identify and mark the affected areas.

Step 2. Remove trim from these areas of walls and other surfaces, if any.

Step 3. Moisten the molds with water to prevent spores from rising into the air.

Step 4. Spray a strong antiseptic or fungicide on the affected area. The treatment area should be "with a margin" of 0.75-1 m from the visible center of mold. So you cover that part of the fungus that is still growing and is not visible to the naked eye of a person.

Step 5. Wait for the applied product to dry. Repeat the treatment 1-2 times if necessary.

Step 6. Use a scraper, trowel, or wire brush to scrub the affected areas of the wall. If at the same time there are remnants of the old finish on them - remove it.

Step 7. Treat the wall with an antiseptic again.

Step 8. Equip a new bathroom finish - tile or paint.

Preventing the appearance of mold in the bathroom

As in many other situations, the best way to fight fungus in the bathroom is through timely prevention; a set of simple measures will help you in this matter:

  • elimination of the problem of ineffective ventilation;
  • elimination of the problem of excess moisture;
  • regular cleaning of the bathroom;
  • the use of antiseptic additives in finishing materials.

Now let's take a closer look at these measures. As it was written at the beginning of the article, one of the main reasons for the appearance of fungus in the bathroom is poor air circulation when a conventional exhaust shaft does not cope with its task. In this case, the problem is solved by installing a fan. It usually turns on when you turn on the light in the bathroom and while you wash or use the sink and washing machine, the fan circulates air and removes excess moisture. In addition, the simplest, but quite effective measure is to keep the bathroom door open (except when using a shower, of course). This evens out the difference in temperature and humidity between the bathroom and the rest of the apartment.

Eliminate excess moisture problem in the bathroom, four simple steps will help.

  1. Check if the heated towel rail is working. If not, repair or replace it.
  2. Wipe off condensation on the pipes regularly with a cloth.
  3. Repair all leaking taps and connections.
  4. Do not dry your laundry in the bathroom. Use the balcony or other rooms for this.

Regular cleaning of the bathroom will not only make her neat and beautiful, but will also help to destroy the fungus at an early stage, until it grows into a real problem. In this case, be sure to use household fungicides.

Of course, one of the best ways to prevent the appearance of mold in the bathroom is to use finishing materials with various additives during the repair, which will inhibit the vital activity of the fungus and prevent it from developing. Follow all the above measures, regularly carry out general cleaning of the bathroom and the problem of fungus and the need to remove it will bypass you!

Video - How to get rid of mold in the bathroom

Headaches are one of the signs of the presence of a fungus

Mold in the bathroom is a common occurrence that many have probably encountered. There are many reasons for its appearance, but the main one is high humidity. Of course, her appearance will not please anyone, she not only spoils the appearance of the walls of the room, but has a harmful effect on health. Therefore, as soon as the first fungal spots began to appear on the tiles in the bathroom, they must be immediately treated with special means. And how to clean the mold on the tile joints and what is used for this, we will tell you in more detail.

Many people often ask - why does fungus often appear in the bathroom? After all, it seems, it seems that everything is done to ensure cleanliness and order - cleaning, washing floors and walls, using special detergents. And fungal spots still appear again and again, and it is not possible to clean them. To begin with, it is worth finding out the reasons for the appearance of mold:

  • it is possible that during the installation of the tiles the corresponding standards were not observed and mistakes were made;
  • poor ventilation in the room;
  • lowered temperature level in the bathroom;
  • poor-quality cleaning of the premises;
  • high level of humidity;
  • carrying out constant water procedures - drying things, washing.

Often, mold spots appear on the tile joints, which greatly spoil the aesthetic appearance of the room. But don't forget that fungus has a serious impact on health and can cause serious consequences. Therefore, at the first detection of stains on the seams, it is necessary to immediately process them. For removal, you can use a special antifungal primer mixture. The seams are thoroughly wiped with a primer until the stains are completely removed. They can be covered with grout on the sealant.

In addition, the bath and the bathroom must be ventilated after taking a bath or shower, washing. To do this, you need to open the door. It is advisable to install a fan in the ventilation duct to blow the room. Due to this, moisture will be eroded faster.

It is good if the room has a hot heated towel rail or radiator. If these elements are missing, then a heater can be installed there to heat the room. It is also imperative to do cleaning using detergents that protect the tiles from fungal and mold stains.

Locations of mold stains

We sort of figured out the reasons, now it's worth finding out where spots of black or green fungus can appear. This will simplify the work and also save processing costs.

In the bathroom, fungal accumulations often appear in places:

  • spots of black or green color often fill the seams of the tile covering;
  • fungus can appear in the corners of the room;
  • at the joints of the walls;
  • sometimes mold can be found in a shower stall, between shelves, in any spaces of cabinets, walls.

Mold in the area of ​​the mixer

Mold in the corner of the room

Mostly fungal spots appear in places with an increased accumulation of moisture. Be sure to wipe everything thoroughly during the cleaning process and check for mold spots.

How to get rid of mold

Of course, the best way to get rid of mold and mildew stains is to keep them out. But if, nevertheless, they appeared, then it is necessary to immediately start cleaning them.

The joints between tiles can be cleaned in many ways. But before processing, it is necessary to prepare special mixtures for cleansing. For mildew stains, you can use the following products:

  • household chemicals, which include chlorine. Household chemicals include "Whiteness", "Domestos" and products that contain chlorine. These mixes are great aids in the fight against mold. They not only remove it well, but also disinfect the place. In the future, mold spots do not appear in places treated with chlorine-containing mixtures;

Household chemicals with chlorine

  • special antifungal drugs designed to combat mold at home. One of these products is Polymix. This mixture contains a microbiocide in the form of a quaternary ammonium. The drug has a destructive effect on all kinds of fungi, mold, pathogenic bacteria and microorganisms;

Polymix

  • baking soda;
  • alcohols and alcohol-containing compounds;
  • antiseptic agents - hydrogen peroxide, potassium permanganate;
  • products containing strong acids - acetic, oxalic;
  • copper sulfate.

Folk remedies for mold

Cleaning process

The cleaning agent has been selected, now it is worth preparing the necessary equipment for processing:

  • for ease of use, the seams can be cleaned with a toothbrush. For these purposes, use an old unnecessary brush;
  • wiping cloths;
  • many products can be harmful, it is better to use a respirator;
  • so that the skin of the hands does not suffer, you can use rubber gloves;
  • container for diluting the detergent mixture;
  • a spray gun for spraying the mixture on tile joints with fungus spots;
  • sponge with a hard surface;
  • thin brush;
  • bucket.

We proceed to the treatment of the bathroom itself:


  • for this, it should be poured into a small cup;
  • moisten the toothbrush a little with water and put a little baking soda on the bristles;
  • then you need to brush the seams of the tile covering with a baking soda brush. Cleaning is carried out until the stains are completely gone;
  • with alcohol and antiseptic preparations, cleansing is carried out using a spray bottle;
  • the solution is sprayed onto the seams and wiped with a cloth;
  • you can get rid of mold stains with vinegar. Moreover, this remedy is found in everyone in the house;
  • in a spray bottle you need to pour up to half of water and the same amount of acetic acid. Everything mixes well;
  • the mixture must be sprayed onto the seams of the tiled wall covering in the bathroom;

When cleaning walls from mold, be sure to use a respirator

  • after a while, you need to clean the fungus with a brush or sponge;
  • at the end, remove everything with water and a damp cloth;
  • processing can be done with copper sulfate;
  • for this, copper sulfate in an amount of 50 grams is poured into the bucket, 5 liters of water are poured;
  • with this mixture, the places between the tiles are smeared. A thin brush should be used for lubrication;
  • leave the mixture for 2-3 hours. After that, we clean and rinse everything.

Replacing grout

Sometimes it is not possible to clean the mold with these products. Then you will have to make repairs, of course, you will not need to completely change the tiled coating, but you will have to redo the seams.

How to do:

  1. if mold spots have appeared on the sealant and cannot be removed with special means, then they should be redone. First of all, we clean the mixture with a nail, spatula or other device;
  2. then you need to purchase a lubricant for seams with an anti-fungal and moisture-resistant effect. It is desirable that it be on the sealant. The sealant does not allow moisture to pass through;
  3. the mixture is applied to the intervals of the tile covering with a rubber spatula.

Sequence of actions when replacing grout

Application of an alternative method

As an alternative to detergents and other preparations against the fungus, action using the microwave method can be used. Many people note that exposure to microwaves does not have a damaging effect on the finish, in addition, with this method, mold stains can be removed.

Removing mold with microwave

The thing is that during processing microwaves act pointwise, namely only on the affected areas. This treatment is carried out using a special device that generates electromagnetic waves and creates vibrational processes of water molecules in microorganisms. These processes occur most intensively in places with high humidity. It is worth noting that fungal microorganisms consist of almost 90% of water and as a result of this effect, their heating occurs faster, in contrast to finishing materials. This all ensures the rapid destruction of mold.

Further, this coating will protect against the appearance of mold spots and strokes. And the walls and appearance of the bathroom will always be beautiful. Using this method, you can get rid of almost any fungus. But before processing, you need to make a full check of the room for the presence of fungal stains.

Prophylaxis

Getting rid of mold spots and mildew is very difficult and sometimes causes a lot of problems. Therefore, so that she does not bother again, it is worth following the rules of prevention. They will help prevent the development of this trouble on the tiled flooring in the bathroom:

  • first you need to determine the cause of the appearance of mold spots. Sometimes replacing the grout will fix this problem permanently. Use grout-on-sealant mixes. No fungal accumulations appear on the silicone coating;
  • it is advisable to disassemble, clean the ventilation. It is better to install a fan from the side of the bathroom;
  • do not dry a large amount of laundry in the bathroom, because it can create a high level of humidity in the room;
  • the bathroom door should be kept constantly open so that air constantly gets into the room;
  • after taking a shower or bath, be sure to wipe the walls, plumbing and floor with a dry cloth;
  • plumbing must be regularly checked for water leaks;
  • be sure to monitor the condition of soap dishes, cups, because these things are breeding grounds for fungus. They must always be washed and without water;
  • all possible joints should be treated with a sealant so that water does not seep there;
  • periodically do the cleaning in the bathroom. It is necessary to rinse the walls and floor with water. You should also use detergents - powders, gels, whiteness. All this will help prevent the appearance of mold again;
  • if iron pipes are installed in the room, then it is better to replace them with plastic ones. Usually, moisture constantly accumulates on iron products.

Getting rid of mold and mildew in the bathroom is not an easy task, and it takes a lot of time and effort. To remove fungal accumulations in the bathroom, you can use various agents that have antifungal effects. The main thing is to do everything right, then you can remove this problem completely and for a long time.

The beauty of a bathroom lies not only in beautiful and stylish tiles, expensive exquisite sanitary ware and furniture. The main indicator is cleanliness and well-groomed appearance. Regular cleaning, washing the floor and plumbing does not help to avoid the appearance of fungus. There is a high level of humidity in the washroom. Poor ventilation contributes to the appearance of a dark coating on the seams between the tiles, the ceiling, the junction of the walls and the bathroom. This plaque spoils not only the appearance of the room, but is also a threat to the health of the inhabitants of the house.

Where does the fungus come from

Many housewives are perplexed about where the mold appeared in the toilet, because this room is regularly cleaned. Mold develops by spores. They are always in the air. For active growth, they need certain conditions: a stable warm temperature and humidity of at least 90%. Therefore, the fungus does not appear in cold or well-ventilated rooms. The bathroom is the perfect place for many reasons:

  • constant use of water maintains a high level of humidity (the threshold of 90% is often overcome);
  • insufficient ventilation (one small strangler is responsible for ventilating the air in the room; there are no windows in the dressing rooms);
  • complete lack of sunlight;
  • frequent condensation.

The habitat of mold can be the ceiling, tiles (especially the seams), walls, shower surfaces, and a bathing curtain. Under favorable conditions, fungal spores develop at a rapid rate. If you do not get rid of small black spots in time, over time they will turn into large foci. The more the fungus has grown, the more difficult it is to find an effective way to remove it.

Harm to humans

There are three main types of mushrooms:

  • blue (does not pose a danger to apartments and houses, is formed on wood, especially on pine);
  • decay (it is also dangerous only for wood, the decay process due to fungal attack cannot be stopped);
  • moldy (can form on wood, concrete, plastic, sealant, brick and painted surfaces).

Mold can lead to a number of health problems. Some people notice a sharp deterioration in health (headaches, cough). If you do not fight the fungus that has appeared in the bathroom for a long time, you may experience coughing, asthma, runny nose and even rheumatism. People prone to dermatological diseases note the appearance of dermatoses. Young children can develop allergies, causing discomfort in later life.

How to normalize moisture levels

Before removing the mold, you need to create an unfavorable environment for its development. First you need to check if there are any unnoticed water leaks in the bathroom. This can be the outgoing drain hose of the washing machine, a hole in the pipe, a leaking joint between the bath or shower stall and the wall. A non-drying puddle of water is a surefire way to maintain a high humidity level in a room. The source of the fungus is often the shower tray or the floor under the bathtub.

The second step to normalizing humidity levels is good ventilation. The ventilation duct is responsible for this. Ventilation is often impaired in old multi-storey buildings. In this case, it is necessary to equip an additional ventilation unit in the toilet or purchase an air dryer. Don't keep the bathroom door closed. It is a bad habit to keep moisture in the room. Do not dry towels in the bathroom; take them out to the balcony or another room with better ventilation.

Removing the fungus

You need to act immediately after detecting black plaque. If the fungus in the bathroom is not removed immediately, colonies will spread along the walls, mirrors, furniture and ceiling. It is much easier to remove mold from a smooth enamelled surface than from a rough plastered wall. Mold can be removed with proven "grandmother's" means and aggressive modern antiseptics. Folk remedies are impossible to cope with the fungus in advanced cases.

Traditional methods

Professional solutions based on chemicals and acids appeared on the market relatively recently, and mold has always been present in the life of mankind. The perennial problem forced people to find ways to overcome it with folk remedies. Most of them are toxic. You need to work with them in gloves and a protective mask. Small children and pets must not be in the apartment.

Creosote

Creosote is far from a harmless remedy. It is made on the basis of tar. The oily, yellowish liquid has a very pungent odor. It is better not to use creosote in its pure form. Dissolve it in alcohol or ether. The resulting solution can only handle smooth, dense surfaces (walls lined with tiles or plastic panels, furniture, concrete, ceramic products, bricks). It is strictly forbidden to apply creosote to wooden surfaces. The product will instantly be absorbed into the loose structure. It will be impossible to wash it. After treating the surfaces affected by the fungus, wash them with soapy water.

White vinegar (natural) is one of the folk remedies that can help get rid of small spots of mold. This product is indispensable in cooking and in everyday life. Experienced housewives know that vinegar helps clean many surfaces of dirt. The acid helps to cleanse the bathroom of mold growth. Many women are scared off by a specific pungent smell. You don't have to worry: it will disappear within a couple of hours after surface treatment.

Pour vinegar into a spray bottle and apply to moldy areas on walls or ceilings. Spraying facilitates better penetration of the liquid into the surface structure. Smooth tiles can be treated with a sponge soaked in vinegar. Wait for it to dry. After that, you need to remove the dried remains of black mold with a dry cloth or brush. Be careful, as black streaks may remain on rough surfaces.

Hydrogen peroxide or ammonia

Both pharmaceuticals can be purchased for a penny. Peroxide is preferred as it is odorless. It is very difficult to work with ammonia for a long time. Spray hydrogen peroxide on walls, furniture, or ceiling with a spray bottle and wash off the fungus with a damp sponge. A cotton swab dipped in peroxide can be used to wipe rubber and plastic products and sealant seams. Remember, hydrogen peroxide is a bleaching agent. Avoid rubbing too hard on dark plastic surfaces and tile seams.

Bleach

Any chlorine-based detergent will help get rid of fungal diseases: bleach, toilet cleaner, stain remover.

Dissolve it in water in equal proportions and apply to the surfaces affected by the fungus. The persistent smell of chlorine will disappear after a couple of hours of airing the apartment.

A similar effect is possessed by:

  • strong soda solution;
  • tea tree oil;
  • copper sulfate;
  • boric acid.

Wear rubber gloves, a respirator, and safety goggles when handling any of these items. In case of contact with the eyes, the substance may burn the cornea.

Professional antiseptics

The most popular remedy is the Antifungal solution. It is used as a prophylaxis and in case of damage to walls or ceilings by a fungus. At the stage of repair, they are treated with surfaces before laying tiles or gluing wallpaper to prevent the appearance of mold on the walls or ceiling. The manufacturer advises adding the agent to wallpaper glue or beauty in a ratio of 1: 100. This will not reduce the quality of the material and will serve as an excellent preventive measure.

Other popular remedies:

  • "Isocide". It is produced in the form of a solution in a container with a spray bottle. It is applied at the stage of repair and in the case of multiplication of microorganisms. It is used for processing wood, concrete, brick, plastered walls before painting.
  • Mill Kill. Available as a primer. Used at the stage of renovation work. The primer is safe for use in the kitchen.
  • "Dali". An antiseptic is used to destroy large fungal foci. The solution is absolutely safe. Can be used in the kitchen. Suitable for wood processing.

Before buying chemicals, try to "drive away" the fungus using folk remedies. This way you can save on the purchase of the solution. The best way to protect against fungus is to treat surfaces during the renovation phase.

Fungus and mold appear quite often in various places of the living quarters. Almost everyone can have such a problem, so many call it universal. In addition, it should be noted that it is very difficult to deal with it.

Most often, mold occurs in bathrooms, lavatories, and attics.

The causes of the appearance of the fungus

Fungus usually occurs due to maximum exposure to moisture.

Increased humidity occurs in the following cases:

  • Insulation is poorly done.
  • Freezing of wall blocks.
  • Inoperative ventilation system.

It is worth noting that faulty ventilation is most often the cause of the occurrence. If, in addition, plastic double-glazed windows are installed in the room, imported doors contribute to the maximum development of the fungus, leading to an unfavorable microclimate in the apartment.

The fungus will definitely appear in the bathroom due to the fact that ventilation does not work there and there is high humidity.

It is where the corners are very poorly ventilated that fungus occurs. For this reason, it is necessary to ensure that the rooms are ventilated efficiently. In addition, it is recommended to install a forced ventilation system.

It is easy to detect freezing of wall surfaces, in this case, moist dark deposits will be observed in the corners or along the edges of the wall. If such a defect is found, immediately dry the damaged areas, check the adhesion of the plaster layer.

The problem arises much less often in apartments located on the ground floors. The cause is moisture coming from the basement soil.

It can also occur with a faulty sewer system. In this case, the fungus appears along the pipes or along the edge of the tub. In this situation, it is necessary to dry the room well. Otherwise, expensive repairs will have to be done.

In the event of a gutter or downspout leakage, dampness enters the room and dark growths form on the wall. If timely repairs are not carried out, then the appearance of mold is guaranteed.

The first signs of the appearance of a fungus

If the fungus does not yet have visible traces, it can be detected in several ways:

  • There is a damp feeling in the apartment.
  • It becomes hard and stuffy to breathe.
  • If you touch the walls and corners, you will feel damp on your hands and a corresponding smell appears in the apartment. , was covered here.
  • If the living space is not high, double-glazed windows are installed in it, and the ventilation hole does not show signs of life, this will inevitably lead to the formation of a problem.
  • If the apartment is flooded with rainfall, in winter the wall will definitely freeze, and in spring, with contrasting temperature conditions, a fungus will appear, which will begin to grow very quickly.

The harm and consequences of the fungus


 and not only spoils the things and surfaces of the apartment, changes the appearance of the premises for the worse, it has a rather negative effect on the health of the people living there. Most often, people with a weakened immune system are exposed to diseases of a different nature.

These people include old people, babies suffering from chronic diseases.

The main thing in this situation is that it is impossible to determine the cause of the disease. Spores enter the respiratory system and cause a number of fairly serious diseases.

Disruptions in the activity of the body can manifest themselves in various ways:

  • Skin diseases that are difficult to treat and diagnose.
  • Respiratory tract diseases. This is associated with a sudden manifestation of cough, runny nose, and even bronchial asthma may develop.
  • Diseases of the joints.
  • Dizziness.
  • Headache.
  • Exhaustion of the body.
  • Nausea and even vomiting.

The fight is pretty hard, but possible. For preventive purposes, you do not need to let her develop freely. The apartments should be warm and dry.

The sequence of actions when removing the fungus from the walls

As everyone knows, fungus can be a major health problem for indoor residents. It is the cause of diseases of various severities. If in the apartment, especially in the corners, spots of a black, green or yellowish hue are observed, this is mold, it simply multiplies rapidly.

If a rather unpleasant odor is present, this indicates that it is already in an advanced stage.

Getting rid of her in an apartment is quite problematic, but still possible.

Important! Before starting work on the removal, it is necessary to thoroughly find out the cause of the occurrence and, first of all, get rid of it.

Actions to remove fungus from surfaces should take place according to the following scheme:

  • Carefully, wallpaper, plastering, where the mold was located. The plaster must be well soaked, the paint must be removed with a construction hair dryer - after preparation, the layers are perfectly removed with a spatula.
  • Using a metal brush, remove the top layer of a surface consisting of concrete or brick, in this case all fungus spores will be removed.
  • Dry the wall surface thoroughly with a construction hair dryer or blowtorch. Under the influence of high temperatures, you can not only dry the wall well, but also kill all fungi.
  • Treat the already dried wall with antifungal drugs. To do this, you can use not only professional means, but also use folk methods. In these cases, apply the liquid to the surface with a roller or wide brush. It should be remembered that in such cases, not only the affected area should be treated, but also a wider area should be covered.
  • When the protective agent is well absorbed into the wall, you can apply soil mixtures, putty and plaster compounds. Only after the treated surface dries well enough can you start painting and wallpapering.

If wood surfaces are affected by mold, there is only one way out in this situation - to cut out the damaged area and immediately burn it. So that the wooden bases are not affected, they should be treated with antifungal drugs at the initial stage of construction.

It was discussed in detail here.

If there is a suspicion that the walls are not soaked well enough, they need to be treated with these compounds several more times. Subsequent layers are applied after the previous one has completely dried.

You can enter and use the premises that have undergone treatment only after a few days. During this period, all toxic and unpleasant odors will disappear.

Special remedies for fungus

In order to permanently get rid of the fungus, it is necessary to identify the cause of its formation and, only after that, carry out work to destroy it.

As a rule, the reasons for the appearance of mold are faulty ventilation and high humidity in the room. Only after getting rid of them can the fungal formations be completely eliminated.

For bathroom

Initially, some steps should be taken in the bathroom:

  • Check the function of the hood.
  • Find out where the dampness comes from (it may be faulty plumbing, pipes covered with panels, condensation). Eliminate all detected defects.
  • If there is a washing machine in the bathroom, check to see if any water remains after washing.
  • Get rid of things and pieces of furniture that are affected by the fungus.

In retail outlets, you can buy many different modern means with which you can get rid of the problem forever. You can buy them in any construction or business department. They quite professionally rid the room of corrosion and prevent its further occurrence.

  • Antiseptic agent "Teflex AntiMold". It is used for waterproofing works, when treating affected areas, during finishing works.
  • Antifungal spray. As you know, spores are in the air and, to prevent their development, it is necessary to constantly process the air masses.

For living rooms

The reason for the formation of a fungal problem in living rooms, in addition to poor ventilation, high humidity, is also a lack of heat. This can happen when walls freeze, poor-quality construction (for example, poorly installed waterproofing, etc.).

Industrial chemicals are expensive, but they quickly and efficiently remove all the causes of the occurrence of the fungus, at the same time prevent a new occurrence.

These include the following:

  • - belongs to the most popular drug, has a wide range of effects, it is used not only in residential premises, but also in laundries, where the percentage of humidity is quite high. It also processes objects located on the streets: fences, monuments, etc.
  • "Olympus stop mold" it is used in almost all rooms where the humidity is high, there is low lighting. Under such conditions, the mold builds up quickly enough.
  • "Dali" refers to antiseptic drugs, is great for prevention, it is good to use it when the fungus has already been removed. In this case, the main problem is to prevent its further manifestation.
  • "Fongifluid Alp" effectively combats all types of fungal manifestations, a huge plus is the complete absence of odor.

Universal

The best disposal option is the overhaul of the ventilation shaft so that there is access to fresh air. You also need to take care of the normal functioning of the heating system and the insulation of walls and panels.

If there is no time to carry out major repairs in the apartment, then antiseptic drugs are used with great effect:

  • Olympus stop - mold... Perfectly removes black deposits in damp places (bathtubs, basements, greenhouses and other damp rooms).
    1. Does not contain chlorine and other toxic constituents.
    2. It is completely safe for people and animals.
    3. Colorless.
    4. It is used on all types of surfaces (from concrete to drywall).
  • Neomid Bio... Concentrated product with a dispenser - spray. It contains antifungal and antibacterial agents, plus water. The method of application is quite simple: apply to an untouched moldy surface, after 2 hours remove with a spatula.
  • Active fungicide "Fongifluid Alpa". It is based on anti-fungal and anti-mold ingredients. The purpose is quite versatile - from exterior decoration to interior decoration in the apartment. The drug perfectly penetrates into any crevices and pits. If the surface is severely affected, repeat the treatment several times. Do not use when the air temperature is less than 5 ° C.

In addition to the listed drugs, in retail outlets you can find many other means that are quite effective.

The assortment of manufacturers is constantly being updated, and more and more new drugs are being produced. Which drug to choose depends entirely on the degree, material of the affected surface and on the desire of the owner.

Folk remedies for getting rid of the fungus

The appearance of fungus on the surfaces of the apartment, as a rule, occurs unexpectedly. It should not be forgotten that its presence leads to the occurrence of various diseases, including allergic ones.

Great help to get rid of this trouble, the fight, using folk methods:

  • Bleach - removes almost all types of formations. Its content includes sodium hypochlorite. It is he who removes the fungus along with its spores. The bleaching agent is used to treat and clean floors, walls and glass. Do not forget that frequent use can lead to color loss. For the working composition, it is necessary to take 10 parts of water and 1 part of the drug.
  • Table vinegar. To treat the problem area, the affected surface should be well moistened with vinegar solution by spraying. After one hour after treatment, rinse and ventilate the room. For prevention purposes, you can treat the surfaces with a vinegar solution once a week.
  • Hydrogen peroxide. Perfectly helps to get rid of mold, has no odor, but you need to be careful when processing painted surfaces, they can lose color and brightness. You can buy the drug at any pharmacy outlet.
  • Baking soda... Sodium bicarbonate can be used perfectly. It is odorless, completely harmless to human and animal health. For the working solution, dilute a teaspoon of powder in a glass of water and treat the surface. After drying, you do not need to rinse, this will help prevent re-emergence.

Mold on balconies and loggias occurs less frequently than in apartments, but it does occur. To get rid of this problem, it is necessary, initially, to find the reason where this trouble arose from.

They can be the following:

  • Freezing of wall surfaces.
  • Increased humidity.
  • Dripping rainfall.
  • Poor ventilation.
  • Contact with the ground.

To completely get rid of the problem, get rid of the surface layer on which the black problem has formed. If it is plaster, it is necessary to completely get rid of its layer to the base (concrete or brick).

Before starting work, the surface should be well moistened. Work should be carried out in a protective mask and gloves.

If fungus is observed on wood sheathing, remove it. Waste should be incinerated (if possible).

If the reason lies in freezing, then the surfaces should be insulated. If necessary, get rid of the cause of the dampness (these can be flowers, herbs or vegetables).

Perform surface treatment using the above-described processing methods (folk or specialized). After treatment, take preventive measures against reoccurrence.

Prevention of the appearance of a fungus

  • Linen should not be dried in bathrooms.
  • It is necessary to prevent, if necessary, repair all sources through which dampness occurs (repair, replace faulty taps, replace old sewer pipes with plastic).
  • Apply a special silicone paste to all cracks and holes through which moisture penetrates.
  • Check the operation of the ventilation system periodically.
  • Do not put damp, wet items in cabinets.