To independently make cosmetic repairs in an apartment or in a country house, it is not necessary to have special skills in construction and finishing works.

In their own house, almost everyone is able to personally change the interior, having studied the technology of painting the walls and carefully examining the photo with tips.

Preliminary preparation

An important and very important step is to properly prepare the walls for painting.

Violation of the pre-treatment technology will lead to defects in the final work and the fragility of the updated wall covering:

• Clean the surface of old paint or wallpaper, various contaminants. You can remove rust stains with a solution of copper sulfate, an oil stain with a solution of soda. In the case when there is mold or fungus on the wall, the use of antiseptics and special fungicidal solutions is required.
• Leveling the surface of the wall. Large cracks are cemented, small ones are puttied.
• Wall priming. It is recommended to repeat the procedure twice to increase adhesion and reduce paint consumption.

Before proceeding with the main part of the work, it is worth taking care of the safety of the cleanliness of furniture and non-painted surfaces (doors, windows, floors), you can cover them with a film.

A suitable microclimate in the room should be ensured: temperature 5–20 ° C, humidity 50–70%, absence of drafts.

At elevated temperatures and low humidity, the rapid drying of the paint leads to a deterioration in the quality of work. If repair work is carried out in winter with the heating turned on, it is advisable to additionally humidify the air in the room.

How to paint

The home master must have the necessary tools:

• Foam rubber paint roller (for smooth painting) or fur (for structural finishing).
• A set of brushes of different widths.
• Cuvette painting. You need to make sure in advance that the dimensions of this container and the roller fit together.

Also, when working, you may need a plastic spatula, masking tape, a mixer for stirring paint, additional accessories for original design ideas. For uniform painting of large surfaces, the use of an airbrush is justified.

For painting walls, in most cases, water-based paint is purchased. Having opened a new jar, you should mix the contents thoroughly, if desired, you can add a special pigment to obtain the desired shade.

A roller is used to paint the main part of the surface. During operation, make sure that excess paint does not fall on its axial part, and the soft surface is evenly moistened.

The paint is applied to the wall in vertical stripes up to 70 cm, which overlap each other by 5 cm.

When painting walls with your own hands, you should know that one coat of paint is not enough. To obtain a high-quality result, the surface should be painted over 2 or 3 times, waiting for the previous layer to dry completely, on average 5 hours.

If the paint is applied in 3 stages, then on the second run, the stripes should not be vertical, but horizontal.

In the case when multi-colored stripes border on the wall, then during operation they are isolated from each other with masking tape. In order not to damage the newly painted surface, it should be glued no earlier than after 2 or 3 days.

Decorative painting

The use of a variety of techniques for painting the wall allows you to achieve original solutions when updating the design of the room. You can buy expensive textured paint - durable, wear-resistant, easy to use.

Another option is to use the usual one in a non-standard way:

• Using a stencil when painting walls. You can buy a ready-made template in a store, or make it yourself from a strong material (linoleum, thin plastic, artificial leather).
• Spraying on a dry painted surface of droplets of paint of a different color - the effect of stardust.
• Application of abstract patterns with a modified roller. The color of the picture should not match the main one.

You can experiment with the wall - wait for it to dry completely or not, and with a roller. You can make a “torn” fur coat for a working tool from scattered patches, buy curly nozzles or make them yourself from various materials.

Instead of a roller, you can take a comb, sponge, brush and other improvised items.

The final touch is the application of a transparent interior varnish on the walls to protect the painted surface from external influences.

Repair is a troublesome business, but a pleasant one. Let the renovated premises please you with cleanliness and order for a long time.

Wall painting photo

It confidently occupies a leading position in the market, gradually replacing the usual finishing material - wallpaper. The market responds to such demand with new color compositions, an expanded range and a wide price segment. Next, consider: what types of paints exist, how to paint the walls with your own hands and what kind of pigment suspension to choose for this.

Color boom: wall paint instead of wallpaper

It is difficult to imagine a stylish renovation in the house without the use of paints. Enamel, water-based or acrylic materials decorate the space with new colors, protect surfaces from the negative effects of the external environment, moisture and sunlight.

Varieties of paints for painting the walls in the room

Among the wide range of products for indoor repairs, construction experts distinguish two types of paints.

1. Alkyd: oil, drying oil, semi-gloss, glossy, matte (gloss level subtype), enamel, lacquer.
2. : polyvinyl acetate, acrylic, silicate and silicone.

Alkyd paints are dyes based on drying oil or alkyd resin. These components have a strong odor. Considered hazardous to human health. There are many disadvantages, but one advantage - excellent surface protection from moisture.

Emulsion coloring compositions are used for interior and exterior use. Unlike previous materials, they do not contain third-party odors, dry quickly and offer an unlimited number of shades, colors and combined compositions.

There are 4 main brands of drying oils with various properties and characteristics on the market: MA-021 (film-forming drying oils), MA-025 (combined), GF-023 (griftal), PF-024 (pentaphthal drying oil).

How to paint the walls in the apartment

The walls in the apartment are painted with any of the above materials.

However, emulsion formulations that are odorless, harmless to animals and humans, and dry in 10-20 minutes are more popular, which is very convenient for combined staining with several shades.

What paint are the walls

A practical option for painting walls in a residential area is, which is priced lower than acrylic and polyvinyl acetate paint. However, the latter options are more resistant to moisture. Walls can be washed without worrying about color. Shades of acrylic materials allow you to choose the most appropriate option for a particular room.

When painting walls with alkyd paint, preference should be given to enamels on a glyptal or pentaphthalic basis. The compositions are distinguished by a high degree of resistance to water and various types of abrasion.

How can you paint the walls?

For walls in a basement or storage room, more practical materials are selected - enamel compositions that do not allow moisture to pass through and are resistant to abrasion.

There are two disadvantages - the need to clean surfaces from old layers of enamel paint, as well as vulnerability to alkalis.

For walls in the bathroom, kitchen or hallway, silicone or acrylic paints should be selected. For the children's room, bedroom and living room, the best choice is water-based and polyvinyl acetate paints, which allow you to paint the walls and ceiling in rich colors.

Repair work, regardless of the type of premises and its size, is carried out in compliance with safety rules, which provide for:

1. mandatory ventilation;
2. use of a protective mask;
3. a ban on painting surfaces with enamel compounds in an unventilated room.

• for corners and embossed surfaces, use a brush with a thick bristle;
• for a flat surface in the center, use a roller with a thick but short pile;
• it is necessary to sand all surfaces, regardless of the type of paint;
• before painting, be sure to treat the putty wall with a primer, and only after drying, apply the coloring composition;
• carry out staining in one direction: side to side or up and down;
• calculate the consumption and dilute the color in a large container so that all the walls have the same shade.

Polyvinyl acetate paint based on PVA is not used for painting metal surfaces and elements.

How many times paint is applied to the wall

and its saturation depend not only on the type of coloring matter and its consistency, but also on the number of layers. For cosmetic painting in one tone, one layer will be enough.

But, if the wall is re-plastered, sanded and primed, then it is better to use a double layer, after drying the first layer before applying the second one. This will make the shade rich and deep, without visible translucent stripes.

The market offers various finishes for walls and ceilings both inside and outside the premises. However, as practice shows, wallpaper is increasingly being replaced by more practical and wear-resistant materials - paints. The interior space solution and the choice of coloring composition are largely determined by such qualities as practicality, price and service life.

Useful video

The dream of every good owner is to bring his own apartment to perfect condition. At the same time, high-quality modern repairs, striking the imagination with design features and the use of the latest technologies, will surely be beyond the means of the average citizen. In this situation, the owners are looking for inexpensive solutions, using the cheapest consumables, or even refusing to pay the master, preferring to carry out repairs on their own.

For a long time, painting has been the most economical type of wall repair, but if earlier such an option was considered far from the best, today a wide selection of paints, as well as a competent approach to organizing the process, make it possible to achieve a decent result for little money.

Peculiarities

Painting the walls in the apartment is popular among the owners, largely because they are able to perform such a procedure with their own hands. This does not require any special knowledge or skills - it is enough to have at least minimal experience with a brush (which should remain from the time of study at school) and follow the exact procedure for the result to be both aesthetically attractive and durable.

If paint is used quite rarely for wall decoration in residential premises, then in household premises it is still very relevant. Properly selected dyes withstand the effects of water, high temperatures and steam much better than even good wallpapers would do, while the painted surface is washed no worse than a tile, but it costs much less. If you need to repaint the walls for cosmetic repairs or design updates, it’s also not difficult at all - the procedure will take a maximum of a couple of days and, again, will not require outside help.

In general, wall painting is considered one of the cheapest solutions. a number of possible additional costs must be taken into account. First of all, it all depends on the readiness of the walls, because they must be even and clean, otherwise they will have to be leveled and cleaned of any dirt beforehand, which can lead to an increase in costs even several times. In addition, for better adhesion of the paint to the wall, it is desirable to use soil mixtures, ideally in several layers, which also increases the cost of the project.

A separate cost item is the purchase of painting tools, if, of course, they cannot be found for free. First of all, you will need brushes, ideally two: a wide one for painting large spaces and a thin one for drawing small details and painting hard-to-reach places. If there are not so many of the latter, but the flat surface of the walls is large enough, it makes sense to purchase a paint roller, which will significantly speed up the process. It still needs to be chosen correctly depending on the type of wall surface: foam rubber for smooth surfaces, fur for rough ones. When buying a roller, you will also need a paint pan - a special container with a relief bottom, which allows the painting surface of the tool to be fully saturated with paint. If you need to provide a clear contour separating surfaces of one color from surfaces of another shade, you can not do without a special plastic spatula or masking tape.

Finally, for high-quality mixing of the coloring mixture (especially if different colors were mixed), a special mixer nozzle for an electric drill is purchased.

This set of tools is typical, but not mandatory or exhaustive. To simplify painting, an airbrush or even aerosol-type cans can be used to replace brushes and rollers. With a small area of ​​\u200b\u200bthe room and the use of paint without mixing shades, in some cases they also refuse a drill with a mixer, replacing it with any improvised tool like a stick.

If we talk about the amount of paint needed to paint the walls in the house, then it must be carefully calculated in advance, because if there is a sudden shortage of material, the work will have to be interrupted, and it’s good if the pieces of the walls painted with the purchased mass do not differ in shade. Such calculations are performed according to a fairly simple formula, according to which it is necessary to calculate the area of ​​\u200b\u200ball the walls planned for painting. To do this, the height of each wall is multiplied by its width, and if there are several such walls, the areas of all walls are summed up. Although this area often includes window and door openings, they should not be subtracted - this will ensure that there is enough paint. Manufacturers in the instructions on the banks usually indicate the typical consumption of their products per square meter - it is enough to multiply this figure by the area of ​​\u200b\u200btheir walls, and also add 15% for insurance, to get the amount of paint needed for painting in one layer. If multi-layer painting is planned, the required volume of material is multiplied by the number of layers.

Types of paint

In order for the result to be of high quality and durable, it is necessary to choose the right type of paint. To date, there are several varieties of colorants for repair, each of which has advantages and disadvantages. All of them must be considered in the selection process.

Water based paint

Water-based paints are well suited for painting rooms with medium humidity, so they can be used to paint walls and interior doors in the residential part of the apartment. Such a substance perfectly adheres to most types of surfaces and "breathes", passing water vapor, and, accordingly, interfering with the development of the fungus. This type does not need to be bought in the right color - the consumer can independently add the necessary dyes to the colorless mass in order to obtain the desired shade with perfect accuracy, and most importantly, all this is very inexpensive. Another thing is that the water emulsion is not suitable for rooms with high humidity, such as a kitchen or bathroom, and it also does not hide the unevenness of the wall, therefore it requires an ideally prepared surface.

The choice in favor of this type of dye should not be made when repairing a nursery, as it is unstable to mechanical damage.

Water-dispersion paint

Silicone-based water-dispersion paints are compatible with all types of surfaces and are undemanding to thorough preparation of the wall - the film formed during the drying process can hide imperfections and cracks up to 2 mm in size. The painted surface is able to withstand almost any test - it does not exfoliate from moisture, does not crack or crumble from impacts, and does not fade from sunlight. You can use silicone dyes in any type of premises, but the only drawback that can scare away a potential buyer is a rather high cost.

acrylic paint

Acrylic paint can be relatively inexpensive to replace silicone paint, but there will be fewer advantages - in particular, wall imperfections should no longer exceed 1 mm. Paint consumption will probably also increase somewhat - it has a slightly lower hiding power, so you will have to paint in several layers. Its variety is also textured decorative paint, which, when dried, forms a surface with a certain texture - its advantages and disadvantages are completely similar to ordinary acrylic composition.

Alkyd paint

Alkyd paints include mixtures based on drying oil or varnish, respectively, called oil or enamel, but the characteristics are very similar. They are most often purchased at a very low cost, so they are suitable for those who save with all their might. At the same time, alkyd dyes are quite resistant to high humidity and temperature, as well as to fading in the sun, and they can also add aesthetics to repairs due to the possibility of choosing a glossy or matte finish. However, to dilute such paints, a solvent with a very pungent odor is used, which does not disappear quickly, so this solution is still somehow appropriate in the bathroom, but is hardly suitable for living rooms, in particular, for a nursery. In addition, a wall painted with alkyd paints loses its brightness after a certain period of time, and then it may begin to peel off.

Design

The preconceived notion of paint as a boring material for wall decoration is due to the fact that in the past, when choosing in favor of such a solution, the walls were painted entirely, while modern ideas are to combine different elements of decoration.

This applies not only to colors, but also to different textures - such a combination almost always looks original and interesting, allowing you to highlight the accent, visually increase or decrease the dimensions of the room.

For different rooms, different aesthetic moves are used. In the bedroom, for example, it is permissible to paint even all the walls in one tone, since here the emphasis can be moved, say, to window textiles. At the same time, it is in the living room that paints with some unusual effect should be chosen, since there are no requirements for special endurance here. Textured paints, which are an imitation of the same silk, will help to decorate it. An unusual practice in recent years is to paint the walls in a gradient way, when the shades smoothly move from one to another. This decor looks stylish and modern.

For the bathroom and kitchen, the priority is not the aesthetic effect, but the ability to withstand difficult conditions - for example, constant humidity, high temperatures and more abundant use of caustic detergents than in other rooms. In a kitchen, the accent can be a piece of the wall that experiences maximum load - the so-called apron, which is often laid out of tiles; then you should decide on the colors in such a way that they blend well and are either close shades of the same color, or radically different.

Wall painting is also appropriate in conditions of purely utility rooms - in particular, a pantry. Here, even the cheapest oil paint will be more practical than wallpaper, and the owners rarely come up with ingenious design ideas, choosing for this room one calm tone of color paint and whitewashed ceilings.

The choice of color can affect the perception of the room as a whole.- small rooms are advised to "enlarge" by choosing a light wall finish, and vice versa - inappropriately bulky "reduce" with dark tones. In addition, all modern designers advise choosing a specific color depending on which side the windows of the room face. If they face south, then the room is probably experiencing an overabundance of sunlight and heat, and cold shades can make the atmosphere a little more comfortable. On the contrary, in rooms with windows facing north, one gets the feeling of eternal winter and coolness, which is not always comfortable, because it is more appropriate to use rich warm colors here.

When choosing a shade obtained by mixing different colors, it is necessary to knead the entire mixture at once, otherwise the slightest deviation in proportions can divide the room into different “zones”.

In addition, you should be careful when choosing the type of paints so that they do not turn out to fade in the sun. It may turn out that soon after the repair, the original plan will be violated, or, even worse, one side of the originally plain room will suddenly become lighter than the other.

Work technology

The technology of painting walls in an apartment with your own hands does not contain any too complicated tasks, but it consists of many stages that it is undesirable to skip in order to avoid worsening the final result.

First of all, it is recommended to remove the old paint or any other finish, otherwise it is possible that the new coating will peel off along with pieces of the previous one that has worn out. How to properly remove the previous finish depends only on what type it is. In some cases, it is possible to paint over the old layer. For example, some types of paint or special wallpaper are subject to re-painting, but in this case you need to make sure that such a base is still firmly attached to the wall. Regardless of whether it was decided to leave the old repair or not, the surface must be cleaned of any foreign contaminants, as they do not promote adhesion.

In the case when the old coating was nevertheless removed, the problem of uneven walls probably arises. It must be removed with the utmost care, since paint is not the best masking material. Leveling is carried out using a cement-sand mortar or putty, and in the most severe cases - drywall. The installed drywall sheets immediately solve a number of tasks, including removing the old coating, cleaning and leveling the walls, but such a step can significantly increase the cost of repairs and will certainly reduce the room somewhat. After the wall is cleaned and leveled, it should be carefully primed. Due to this, the paint will become better connected to the surface and its consumption will decrease. Not every primer is suitable - you need to choose the variety that is combined with the selected type of paint.

Only when the primer is completely dry, you can proceed directly to painting.

The correct staining technique involves both horizontal and vertical strokes., since this is the only way to achieve uniformity of tone. At the same time, paint streaks are unacceptable - they will remain clearly visible even after drying, which is unlikely to add aesthetics to the repair. To avoid leakage, the dye should be carefully diluted. Do not add too much water or solvent there. At the same time, some types of inexpensive paint are sold exclusively in white, then they will have to be tinted with a special color scheme itself - a color additive that allows you to perfectly accurately get the desired shade.

The staining steps must be followed in strict sequence. Today it is not customary to paint literally the entire surface of the walls with paint of the same color, so they should first be divided into sections delimited by masking tape. Coloring involves the application of just a few horizontal stripes, which are then shaded with an ideally wrung out tool - a brush or roller. Finish shading by moving from top to bottom - as excess paint could drain.

When using paint of different colors for curly painting, you can’t do without marking with a special masking tape - then random “climbing out” beyond the necessary will remain on it, and not on the walls. It is necessary to peel off such a masking tape only after the paint has completely dried, otherwise contour violations cannot be avoided.

If there are pipes in the room that also need to be painted, it is worth starting with them. The surface of the pipes and the space behind them are hard-to-reach places, however, such a painted interior detail can greatly interfere with the painting of the walls.

Tired of the monotony in the interior? Would you like something like this? It's time to think about decorative wall painting, which allows you to achieve original and unusual effects.

Tools used for decorative

Experts say that thanks to a special set of tools, it is possible to achieve a decorative effect even using ordinary paint. These are rollers (ordinary foam, fur, rubber or texture), brushes, brushes, scrapers, spatulas (plastic, metal, rubber, toothed), Venetian trowel, sponges (foam and natural, marine), pieces of crumpled paper and fabric, bars for sanding, sandpaper and stencils.

You do not have to spend money on acquiring all this arsenal: what exactly you need from the list will depend on what effect you want to get on the walls. The cost of all these tools is not so high, but they will last a sufficient time - if you handle them carefully, and rinse immediately after painting.

Craftsmen figured out how to use even more affordable analogues instead of some tools. For example, a texture roller can be made from a regular one using a piece of cloth or a plastic bag and rope. The paint application pattern will turn out to be unpredictable and interesting, and no one else will have this for sure.

Professionals consider decorative wall painting one of the most economical ways to transform rooms. Paints are applied in 1-2 layers (the 2nd layer of paint usually takes 20% less). So the 1st can of 2.5 liters may be enough to cover 40 m2. The exact consumption of material will depend on what effect and tool is used.

The services of specialists in decorative painting of walls are expensive. And this is the case when you can save a lot by doing decorative wall painting with your own hands. The main thing is to carefully study the instructions for application and a variety of options for obtaining decorative effects.

Read also: How to level an old wooden floor? Ways to level the floor from the boards

Interesting effects using a textured roller

In order to create a glazing effect or, in simple terms, spectacular blurry spots, deep colors of various saturation, the wall must first be painted in the base shade. After that, with a crumpled dry (or wet - to get a softer ornament) piece of fabric (or a plastic bag), the pattern is randomly stuffed with paint of a shade different from the base color. Other things that can create texture are quite suitable for a similar purpose: sponges (give a soft spotty ornament), a brush (spray method), and also your own palms.

A “wallpaper-like” ornament is created on painted walls using volumetric patterned rollers (they are also called stencil rollers). Rubber or silicone models are used, but pile rollers can also be used, they also create an interesting pattern. To get a good result of the work being done, before applying the drawing, it is worth conducting a trial painting (on a sheet or somewhere at the bottom of the wall), and already in the process of work, regularly remove excess paint from the roller so that ugly streaks do not appear.

As noted above, you can create an interesting textured roller with your own hands. To do this, an ordinary roller is put on a “fur coat” made of sponge, rag, suede, paper or film (all this is fixed on the surface with the help of threads). With the help of such an unusual tool, a chaotic spotted ornament is imprinted on the walls.

To create a marble ornament, two colors of the main shade are taken. First of all, the walls are painted in the main background shade. Then, using a wide brush, uneven stripes are applied to the wall, running parallel and not painting over the entire surface of the wall. As a result, we achieve an original and beautiful ornament. In those places where the two primary shades are mixed, a third color appears. After that, a pattern is applied with a thin brush that imitates the veins of natural stone. Then, after the layer dries, the final finishing is performed. For this purpose, you need to take a small sponge and moisten it in paint, previously diluted with water. Then, with a sponge, it is necessary to blot the entire surface of the wall - as a result, a beautiful smoky effect is obtained. If you apply paint of various colors on the wall in 2-4 layers, and then brush it along the wall with a stiff brush and cover the wall with wax, you can also get a “marble effect”. If you walk over the layer of paint with a cloth (this method is called “rolling the cloth”), you get the illusion of falling folds. We “comb” the not-dry layer of paint with a brush with hard bristles, holding it parallel to the wall, and we get an imitation of a coarse natural fabric (“linen” technique).

Read also: How to putty the ceiling with your own hands?

Water emulsion will help to get the illusion of crumpled paper. For this purpose, another layer of paint of a different color is applied to the dried 1st layer with a crumpled plastic bag. You can replace the crumpled bag with a sponge, which also helps to create the illusion of a grainy and textured wall.

How to apply decorative paints

A variety of types of decorative wall paints, presented on the modern market, provide a huge expanse for the implementation of creative ideas. The advantage of these unique ready-made compositions is that their application does not require special skills and the use of special tools.

Compositions with the effect of mother-of-pearl ("chameleon paints") change their color at different angles of illumination, which creates the impression of walls covered with silk fabric.

In coloring compositions with the effect of velor or velvet, solid multi-colored particles are present. After applying such paint, the surface of the wall becomes textured, visually soft, deep - like a real velor fabric.

A feature of granite (mosaic) paint is the multi-colored acrylic bubbles included in this mixture. When painting from a spray gun, the bubbles break against the wall, as a result of which a perfect illusion of a granite texture is created.

Recently, painted walls have become a favorite again. But ordinary paint is no longer interesting. There are now compositions with different effects. They are called decorative wall paint. They can be used both in living rooms and in technical rooms. Different compositions, different properties.

What is decorative wall paint and how to apply it

Decorative paint is called, which creates some visual effects. This group does not include the usual opaque monophonic compositions. Only those that differ from them in some way. These compositions reproduce different natural materials. Silk, velvet, plush, sand, natural stone, leather, velour, etc. They are sometimes called decor paints, since this is not just a background, but an independent decorative element.

Decorative wall paint with silk effect - an element of decor in itself

Most often, decorative paint is applied as usual - with a brush, roller or spray gun. If the texture itself is “rich”, this is quite enough. The walls already look unusual. In this case, they are just a background. Beautiful, unusual stylish, but the background.

Rollers with embossed relief - easy and simple to get an unusual wall decor

To get more interesting surfaces, special application techniques are used. The simplest are embossed rollers. They break up the monotony of paint by adding relief. There are other tricks as well.

• The applied paint is rubbed off. So from "silk" paint you can get wet silk or plush.
• Partially erase the paint with crumpled paper, a sponge, a piece of fur, plastic or metal notched trowels, steel wool, etc.
• From above they pass with a semi-dry roller or a hard brush with a darker or lighter paint.
• Apply a plastic film to the painted piece, crumple it a little and remove it.

Some ways to get creative

In general, there are a lot of options. This process is completely creative and there are many variations. And the result can be very different, even if you use the same paint.

Decor paint effects

As already mentioned, decorative wall paint reproduces certain textures of natural materials. In this case, they often talk about the paint "with effect." For example, with the effect of silk, sand, stone, leather, etc. There are many options and variations, and you can get lost in specialized catalogs. It will be a little easier if you have an idea of ​​what can be found and what it might look like.

As you can see, the list alone is impressive. And different colors will look the same effect in different ways. This is due to the fact that components and placeholders differ. And the difference is sometimes significant. In general, it is usually difficult to decide. But know that whatever you choose, it will be interesting.

Decorative wall paint with the effect of silk and silk threads

Silk-like wall paint is available from many manufacturers. If there are at least a few decorative or interior paints, then one of them is silk. The look is very sophisticated and delicate. Suitable for living rooms, bedrooms. In terms of performance (acrylic can be washed with a brush) it can also be used in the corridor, but if you are satisfied with such a “refined” look of your hallway.

When choosing, pay attention to the base. Safety is important for a home. The best option is a silk-effect paint based on an aqueous acrylic dispersion. It is relatively inexpensive (when compared with silicone, for example), is washable, does not fade and can be dyed in all colors. Many decorative paints are made on this basis. To obtain a paint with the effect of silk, a special kind of mother-of-pearl and pigment are added to it.

It looks like interior silk paint on the wall

Paint consumption is average, you will have to paint in two layers at least. This is with low absorbency or pre-priming. An absorbent surface will require three coats exactly. And the paint is not cheap, so it is better to primer. If the paint is based on acrylic dispersion, then we take acrylic primer. But better than the same company as the paint. There will be no product compatibility issues.

Of the disadvantages - the surface for staining should be flat. Almost perfectly flat. The second point - if you want to get "exclusive", you need to master the application technique. You can, of course, just roll it with a roller. It will also work well. But it might be more interesting.

You can wash with a detergent (not abrasive), a rag or a brush. Such cleaning does not affect the appearance. In the sense that it does not get worse. Where the walls are often touched, “glossy” places may remain. If you want to have such a coating in the hallway, consider varnishing. But this type of paint "breathes", so when varnishing, lose this effect.

Each company that produces decorative paint with a silk effect, the appearance of the coating is slightly different. Some people have multiple options. And not colors, but textures

If you think that silk effect paint looks the same from all manufacturers, you are mistaken. They use different additives, resulting in slightly different surfaces. This type of decorative paint is popular, so some have several paints that give different textures. There are also different application techniques. With their help, you can get a different type of surface: classic, wet and crinkled silk.

The effect of sand or sand dunes on the walls

The composition of the paint with the effect of sand includes binders, solvents, antiseptics, crystal dispersions. When applied, we get overflows, after drying, the texture appears. With different application techniques, we get a different look - dunes, dunes, sand overflows.

The effect of sand and sand dunes is created using a special decorative wall paint.

The paint is easy to apply, no special techniques are required. Due to the pronounced texture, minor wall defects are hidden. So the requirements for the surface are not so strict.

Application and operation

The paint is easy to apply, no complicated techniques are required. Unless you want to have not just “sand”, but dunes. But to create such an effect, special formulations are required.

Washing the paint with the effect of sand with a brush will not work. Gentle cleaning with soft nozzles on the vacuum cleaner. And keep in mind, if you touch a wall painted with sand effect paint, then the relief crumbles. But this is imperceptible and does not affect the appearance. The surface is initially heterogeneous, the relief just changes slightly. The view does not suffer from this. The service life is up to 10 years, which is not bad at all for paint.

Pay attention to the availability of hygiene certificates for this type of paint. The binder is not always harmless. So the presence of certification and a certificate from the sanitary inspection on the amount of emitted substances is simply necessary.

Structural paint with sand for decorative plaster

Both natural stone effect paints look about the same

A very good copy in terms of performance. Has very good adhesion. Very smooth surfaces - such as plastic - require a primer. The rest can be painted right away. It is applied from a spray gun or using a special roller (of the same company). Appearance depends on the method of application. After the roller, a surface with pronounced flakes of "stone" remains. After the spray gun, the surface is more even.

In operation, this paint imitating stone is convenient and durable. It can even be washed with a brush. For Rust Oleum, additional protection (in the form of varnish) is not required, and for Siberia in heavily polluted areas it is better to varnish. The paint is repairable. If a bald spot or a chip has turned out somewhere, you need to moisten a piece of sponge with water, wring it out and dip it into the paint, apply it to the right place and wait until it dries.

There are also paints under the stone in spray cans. But they are unlikely to be used for painting walls. Unless for a panel, some kind of decoration. It's too expensive.

It looks like stone paint "Alatyr stone"

Another type of surface gives paint with the effect of burnt stone Alatyr-stone. It is also called "liquid granite". It is applied by spraying through an airbrush. There are single and multi-color options. Less shiny than described above. It is positioned as resistant to cracks, ultraviolet. After drying, it must be varnished.

Decorative wall paint in the interior: photo

Seeing what effect paint looks like on a piece of cardboard or on a screen is one thing. And to imagine how it will look in the interior is quite another. To facilitate the task, we have collected several photos of interesting interior solutions. As a recommendation, if you are going to cover all the walls, look towards very light shades. Bright and dark go for accents. These are accent walls, dedicated zones. In general, see for yourself.

Through one color "shines through" another - one of the tricks

And someone calls the gray color boring. Gotta play him right.

Bright color - only on one wall. It also repeats in some small details or has. In this case, the second option is chosen - the color of the floor

Different application techniques give a different look. Chaotic movements are used here with a narrow spatula on a freshly painted surface.

This is the result of rolling with a relief roller. non-standard

Cracked old paint effect. Very interesting, but requires an appropriate interior

Ordered chaos. So you can call the principle of drawing these lines

Triple effect: silk, two colors and stripes

This can be done from paint with mother-of-pearl, silk effect or velvet / velor, metallic