specific gravity of the adhesive. Specific gravity of tile adhesive

One of the first questions that arise when buying tile materials used in the work is how much tile adhesive is consumed per 1 m2.
Since on the basis of this value it is possible to calculate not only the volume of the required material, but also its cost. It is, in principle, impossible to unequivocally answer this question, but it is quite realistic to calculate the approximate consumption of the solution per 1 m2.

How can I calculate the required amount of the mixture?

The first option that comes to mind is to find out about the required amount from the one who releases it. For a particular manufacturer, there are norms for the consumption of tile adhesive from the condition of a constant thickness of the applied mortar. These data are indicated on the packaging and are indicative for the calculation. The table below shows the characteristics of the most popular brands of glue. The spread of values is due to different compositions of mixtures and type of destination.

Options for an approximate calculation of the amount of tile adhesive

As is clear from the presented table, the values are approximately the same and say little about anything. It is better to estimate the consumption of tile adhesive per 1 m2 on the calculator, which is presented by each manufacturer on its website.

In order to use this service, you need to know the area of \u200b\u200bthe room, decide on and select the type of mixture. As a result, you will be given the result in kilograms.

Another simplified version of the calculation under optimal conditions of use: half the thickness of the panel is multiplied by the consumption of the solution indicated on the package, the result will be the desired consumption of glue per 1 m2.

To correctly determine the required amount of the mixture, you need to take into account all the factors affecting this value.

Factors Affecting Adhesive Consumption

The first thing that determines the consumption of the mixture is the type of surface and its general condition. The smoother the wall and the less bumps and cracks on it, the less glue goes. That is why professional builders recommend pre-preparing the base with a less expensive finishing material such as plaster.

In addition, the reverse side of the tile can also have an uneven surface, and then an additional layer of mortar is applied to it.

The next parameter that determines the required amount of glue is the material of execution of both the wall and the tile itself.

Each material has its own porosity, depending on which it has a certain absorbency. For example, concrete walls absorb the least mortar. To reduce the consumption of tile adhesive per 1 m2, the base is carefully treated before

Tiles are also made from different materials. The smallest amount of glue disappears on porcelain stoneware panels, the largest porosity in cotto tiles.

The size of the panels also plays a role, the larger the tile, the thicker the layer should be.

Much depends on the method of installation and the professionalism of the masters. The more experienced the finisher, the thinner the layer of glue he can put without losing the quality of the fastening.

Varieties of glue

Before determining the consumption of tile adhesive per 1m2, it is necessary to choose which composition will be used. There are three main types of tile mix:

1. Dispersion - a ready-made composition, it is extremely convenient because you do not need to waste time on its preparation. It is good because it has ideal plasticity and viscosity, which allows applying the solution in an optimally thin layer.

2. Cement-based adhesive, the most inexpensive mixture that is sold dry and needs to be diluted. Thanks to cheap components, it is very popular and is used in 80% of cases. This type has its own way of calculating consumption, approximate, but giving at least some idea of the required amount. To determine the consumption, it is necessary to know the thickness of the adhesive layer, which is calculated based on the size of the tile. We multiply the thickness by 1.3 (this is the average weight of the tile adhesive) and we get the desired result.

3. Epoxy mix is commonly used by professional finishers as it requires some experience to make. For dilution, a special catalyst is used, which provokes a chemical reaction.

Spatulas used at work

A lot also depends on the size and type of spatula. To apply the solution, a spatula of a certain shape is used. If it is incorrectly sized, then the consumption of tile adhesive per 1 m2 increases significantly.

1. Adhesive consumption directly depends on the angle of the spatula during application, the larger the slope, the greater the consumption.

2. Most of the glue is consumed when applying the mortar with a square-toothed trowel, the most economical option is a V-shaped tool.

So how much glue do you need to buy?

Experts suggest taking 10 kg of glue per 1 m2 with a layer thickness of 10 mm as the norm. Even if you do it yourself, it will be more than enough. In order to reduce the consumption of tile adhesive per 1m2, the advice of professionals suggests carefully studying the technology of applying the solution and following the recommendations from the manufacturer.

Recalculate, find out volumetric weight: physical properties.	Values.	The amount of kg in 1 liter, kg / liter.	Reference data from:	Now you can find out how much it weighs with a tool like:	Measurement error.	-
How many kg in 1 liter of glue - a liter jar.	We use reference data on density and specific gravity, calculating by the formula we get volumetric weight.	1.3	Handbook of physical properties, GOST, TU.	Liter jar.	up to 5%	-

Remarks, interesting explanations to the question "how much does a liter volume weigh" and some additional information to reference data on physical properties.

In fact, we have 1 liter of glue, a liter jar or a certain amount known in liters, we want to know the mass: how much is its weight in kg or grams. That is, our task is to determine how much it weighs: convert liters of glue - volume units into kilograms - units of glue weight. Having determined the volumetric mass of 1 liter of glue, how much in kilograms, without weighing on a scale. Find out how much it weighs (for example: a liter can), based on the calculated, theoretical, reference data from the table of physical properties: specific gravity and density of glue. Of course, it is better to use not the true, but the bulk density, if you can find the bulk density in the reference book. Which is actually not so easy to do in practice. It is extremely inconvenient to independently recalculate based on physical properties, also because most tables, GOSTs, TUs give specific gravity and density values \u200b\u200bthat are “tied” not to a liter jar, in other units: tons / m3, kg / m3, kg / cubic meter, g/cm3. If you wish, you can spend a lot of time, find the data, independently perform the conversion and find out how much kg will be in a liter volume. However, this option to find out how much a liter volume weighs is not for everyone in a simple and convenient way, especially since it requires searching for additional information on the bulk density of the adhesive and its specific gravity, plus knowledge of the conversion formula. Therefore, we ourselves made such a recalculation on the basis of the physical properties given in GOST and TU, indicated the mass of 1 liter of glue per kg, a liter can, citing it in a separate table of weights and volumes. An extract from the general table is given above. Question: how many kg in one liter of glue, liter volume. Answer: see the bulk density in table 1. How to find out how much it weighs - we measure the mass of glue with a liter jar, on our own, without weighing on a scale. On our site you can find other interesting practical information on density and specific gravity not listed in the usual reference books, tables, GOSTs and TUs, which is not so easy to find on the Internet. For example, for the units of measurement of volume that are more familiar to us: cm3, m3, cube, cubic meter, cubic meter. Household and cutlery measuring products: teaspoon, tablespoon, glass. More than construction, garden, industrial and industrial: shovels (bayonet and shovel), packs, buckets, bags, pallets, barrels, construction or garden wheelbarrows. Transport: tank car, railway tank car, railway car, flatbed vehicle, truck, dump truck. These are the so-called, non-standard containers, often used in practice. Despite all the variety of containers, each of them has its own displacement. And this means that it is possible to recalculate the mass of cargo in kg through the values \u200b\u200bspecified in table 1. Naturally, this technique has its own errors. At the same time, the error in calculating the mass of a large volume will be higher than the error in determining the mass of a liter volume indicated in Table 1.

and areas

Very often, a modern interior design is decorated with fashionable glass transparent mosaics, translucent tiles or light natural stone, designed to bring more light into the room, its airy and voluminous. However, it is not recommended to lay such decorations on a regular mortar, since it is made of gray cement, which will darken the surface and destroy the integrity of the visual perception. To ensure that such problems are avoided, it is recommended to use LITOKOL LITOPLUS K55 white tile adhesive (25 kg). What is its main difference?

Glue features

High-strength white cement is used as the main binder for the manufacture of a dry mixture, giving the finished solution a neutral light color. Tile adhesive not only does not darken transparent finishing materials, but also serves as a substrate to highlight them against the general background of the surface to be decorated. Moreover, the composition of the solution includes latex additives that provide high adhesion with any popular substrates: prefabricated and monolithic concrete, GVL, drywall, cement plasters, it is also possible to lay the tile on tile method, without the need to dismantle the old coating.

In addition, it is necessary to highlight:

Water, - atmosphere - and frost resistance - allows you to work in rooms with varying degrees of humidity and on the street, for example, lining bathrooms, showers, kitchens, bowls of pools, fountains, and so on.
Tile adhesive LITOKOL LITOPLYUS K55 white (25 kg) is resistant to slipping and lack of vertical slip, allowing you to decorate in any order, starting from the middle or from the top of the base.
Developing the material, I increased the time of work with the finished solution, thereby allowing you to correct or within 40 minutes, which is convenient for both professional craftsmen and beginners.

Operational tile adhesive provides for its use in conjunction with the "Warm floor" system.

Additional information in the articles:

after 3 hours

Laying textiles and coverings

after 24 hours

Ready for use

FINAL SPECIFICATIONS

moisture resistance

excellent

aging resistance

excellent

Oil and solvent resistance

excellent

Acid and alkali resistance

Heat resistance

-30°C to +90°C

Mechanical strength

see table

Glue tile

In our building materials store you can choose tile adhesive from any manufacturer, at the best prices, we work with the most famous manufacturers of tile adhesives.

Tile adhesive is mainly used for laying tiles (ceramic tiles), for laying artificial stone, laying paving slabs.

tile adhesive which you buy should be high if you want your tiles to be securely glued.

In our store you will find tile adhesive of the highest quality.

To make a solid tile laying, you definitely need glue. This is known to everyone. But not everyone can immediately calculate how much it will take. Tutu? Two? Bag? Ten bags? Or maybe even a truck? Often this issue is resolved at the very last stage somewhere already in a hardware store or on the market. And the decision on how much to buy is not made by you, but by the sales assistant.

Moreover, he will not give any guarantees that this will be enough for you. Or your worker buys as much as he thinks is enough. But it’s also impossible to make sure that he didn’t take some of the money for himself, without knowing how to correctly calculate the glue consumption per 1 sq. m.

So, you want to know in advance the consumption of tile adhesive per 1m2 and calculate the entire budget. So how to be? How to calculate the right amount of this material?

You can alternatively use tile adhesive calculator. But we are talking about independent calculations, because the calculator is not always at hand, and older people may not be able or not want to use it.

The required amount of adhesive material is measured as follows: the consumption of tile adhesive is multiplied by 1 sq. m of laying, which is multiplied by the total number of meters. As a rule, the area to be tiled is known to everyone. This means that you will only need to find out how much adhesive will be enough for 1 sq. m. In this article we will try to give you a rough idea of how much glue per 1 square. m. you will need.

Data required to calculate the amount of adhesive per square meter

type of glue;
tile size;
type of tile;
the base on which the tiles will be laid;
brand of glue and its composition;
weather;
installer qualification and installation method.
Input data for calculation per 1 sq. m. glue

Type of glue

It is important to know that all its types are combined into 3 large groups: cement-based, dispersion, epoxy.

Glue on cement- the most popular. It is very easy to handle: buy a bag of this powder and dilute it with water according to the instructions (or, alternatively, with a latex additive). It is more economical and easier to work than the others. Its consumption rate is 1-1.9 kg per 1 sq. m. (taking into account 1 adhesive thickness of 1 millimeter).

Dispersive- This is a ready-made adhesive liquid (made on the basis of resin). She doesn't need to be bred.

Epoxy is an application solution that is a resin solution and a catalyst. To teach the desired consistency, you must combine both components. As a result of a chemical reaction, the necessary adhesive solution is obtained. Despite the fact that you will have to tinker with it more than with a cement-based composition, this option is the most resistant to various external influences. Water, low and high temperatures are not terrible for him, in addition, he does not shrink, eliminates the appearance of cracks. It also creates excellent grip on the surface. In this case, the total mass of this mixture in kilograms is not appropriate to compare with the calculations of the cement-based adhesive.

Tile size

As a rule, the larger the size of the tile, the thicker the adhesive coating must be made. Usually for medium sized tiles(not higher than 10 by 10 cm) for adhesive materials on cement, taking into account a thin layer of laying, the norm of its layer is slightly less than 2 mm.

If the sides of the tile are 20–30 cm, the adhesive layer most often has 2–3.5 mm. If the tile is 30 by 30 and 50 by 50 cm, then the adhesive layer can be 3.5–4.5 mm. If the tile has dimensions larger than those already mentioned, then the adhesive can be applied in a layer of up to 5 mm. If laying of plates is supposed, then the application of 1 mm on the plate itself (from the inside) can serve as the norm.

Tile type

The wrong side of the tile is designed to absorb glue. However, different materials can be distinguished by porosity. For example, homemade tiles or a variety of cotto are characterized by increased porosity and, accordingly, absorb more adhesive than less porous surfaces (for example, porcelain stoneware). If glazed industrial tiles are to be used, they will absorb less adhesive than the listed varieties. And porcelain stoneware will absorb it less.

Of course, these (and other) features are taken into account during production. But they also meet universal types of adhesives. In this regard, it is desirable to monitor the absorption in practice during work. It may be necessary to apply an additional amount of the composition.

It is also important to take into account the reverse side relief tiles (for example, porcelain tiles). The more uneven the terrain (and it is often found with homemade tiles), the more adhesive will be needed to adhere to the surface on which the tiles are supposed to be mounted.

When laying tiles on the same area (for example, porcelain stoneware), which has a different thickness, then it is with the adhesive material that you will have to compensate for this difference. Accordingly, this must be taken into account when calculating amount of adhesive used.

The base on which the tiles will be laid

Before laying, you need to have an idea what the surface will be on which the laying will be done: wall, facade, floor. Of course, the smoother the surface, the better. But in reality it is different. Most often there are two cases:

The surface (most often a wall) has a maximum evenness of the relief, the difference of which is not higher than 4 mm;
the surface is very "tricky" and complex, has a lot of drops, potholes, cracks, and so on.

If the surface is flat, then maximum savings and, accordingly, the minimum thickness of the tile adhesive layer are possible. It will only play the role of an adhesive material and will not exceed 5 mm. However, in general, its consumption will need to be calculated based on data on the height of the base and existing potholes.

If surface "twisted", then the situation is corrected by the correct selection of types of adhesive material. Among them there are those that both fix the tile and level the surface. They can even out a difference on the surface of 3 cm. There is a special name for the technology that provides for such styling. It is called "thick-layer" and will require more adhesive mass.

It is also necessary to know before starting work exactly how the tiles will be laid. The consumption of tile adhesive also depends on it. The dependence is very simple: a flat surface - less connecting materials, uneven - more. Very uneven - even more so.

It is also necessary to take into account the material on which the laying will be carried out. If porous surface, then the amount of adhesive mixtures will need to be added. A porous base will "eat" more tile adhesive than a concrete surface.

And the last thing in this paragraph: if laying is carried out on a steep surface(for example, on the facades of buildings or a wall), it would be advisable to apply an adhesive mass to both the facade and the tile itself. This will help avoid possible empty spaces that could cause the tile to fall soon. Accordingly, the amount of purchased material will need to be added.

Brand of glue and its composition

Depending on the manufacturer, the composition of tile adhesives may have different properties due to with various chemical additives. Added substances can contribute to greater plasticity, surface bonding speed, water resistance, temperature resistance, and so on. These same substances can change the consistency of adhesive compositions. This is important, because because of this, a bag of the same volume may end up (when ready) with a different amount of material. And it also affects the amount of its use. For maximum accuracy of calculations, you need to know:

manufacturer (for example, Ceresit, Vetonit);
the name of the tile adhesive (for example, Eunice);
additives.

Read carefully what manufacturers write on packs (bags) with tile adhesive - this will increase the accuracy in the calculations.

Weather

The extreme temperature that tile adhesive can withstand (for example, Eunice) ranges between 5 and 40 degrees Celsius. Comfort mark is held between 17–25 degrees. We take into account that an increased temperature will evaporate water faster and, accordingly, increase its consumption. Temperatures below zero begin to destroy the adhesive composition (Eunice). Therefore, in this case, even when all factors are taken into account, you can miss the quantity. It may require much more than expected even with a margin. Consider also the presence of the windy side. He dries up the water. And she, as mentioned, affects the increased consumption.

Installer Qualification and Installation Method

This is rarely taken into account, but the ability to use a spatula and other tools can also affect the consumption of tile adhesive. The thickness of the adhesive surface is directly affected by the angle of the spatula. Proper use of this tool can cut costs by a quarter! The presence or absence of teeth on it is also important. A V-shaped tool saves adhesive more than a U-shaped one. A U-shaped will save more material than a square-toothed tool.

A novice worker may spend much more adhesive material than an experienced one, because he may not know the technology or have insufficient knowledge of it. He will have to simply throw away some, wipe it off and otherwise dispose of it. If you are an unskilled paver and there are no options, then buy more mixes in advance so that you don’t have to drop everything and go for more.

More about the spatula and the thickness of the adhesive surface

When buying adhesive materials, you should pay attention that in the instructions for all tile sizes, the manufacturer will not indicate the numbers of their layer in millimeters. Those figures that will be indicated in the technical information are spatula tooth size. For example, Ceresit or Vetonit factories advise using a spatula 7 for tiles 20 by 20, and a spatula 11 for 40 by 40. There is no mention of millimeters. Why is this so?

The explanation for this is very simple. To measure adhesive mixtures in mm at the time of their distribution over the surface, the task is almost impossible. There just aren't any measuring tools for it. Also, when applying a new even layer, it will appear infallible. But this is a big mistake - the height of the error will be high and uncontrollable. This causes air holes to appear, which in turn causes the tiles to fall.

Instructions are most often recommended first apply the adhesive with the smooth side of the spatula, then level it with the notched side. The most common teeth are 6, 8, 10 and 12. Manufacturers rely on the properties of their material and therefore confidently recommend the use of a specific size. That is why, without reading the instructions of a particular manufacturer, it is impossible to predict the layer of glue and its amount.

With all this, one should also not assume that a spatula of 8 will give a layer of glue for this number of millimeters. This will be erroneous. The size of the teeth at 8 mm suggests the original height of the tooth itself, and not the layer that it gives at an angle of ninety degrees. But this is ideal. There are several reasons for this:

you will not get a constant right angle;
the tile laid on the adhesive deforms its layer under its own pressure and smears it over the surface;
under the tile, the layer will change its height.

However, there are some guidelines. The height of the adhesive layer will not exceed 0.3–0.5 of the size of the spatula teeth. It is calculated like this: spatula at 8 will give a layer of glue 2.4-4 mm. This is, of course, an approximation, due to the difference in the angle under which you will apply the glue.

Based on the information in the instructions, you can more or less accurately calculate the height of the adhesive layer with the specified spatula.

Glue consumption per 1 m2. Consumption rates for tile adhesive.

In repair without glue anywhere. But the question always arises, how much glue to buy, for example, for laying tiles? It seems that let there be more glue than not enough in the midst of repairs. This issue must be resolved at least to calculate the cost of repairs.

So, tile adhesive is usually packaged in kilograms. Therefore, you need to determine the glue consumption per 1 square meter, and then calculate the total amount based on the area of \u200b\u200bthe room. But, there is no definite answer to the question of how much tile adhesive is consumed per 1 square meter. Everything depends on many factors.

1) Glue type

Tile adhesive is divided into 3 groups: dispersion adhesive, epoxy adhesive and cement-based adhesive. The most economical and easiest option to work with is cement-based glue (diluted with water). Depending on the thickness of the layer, the average consumption of such glue is 1-1.9 kg. The dispersion adhesive is ready to use, it is resin-based and has a liquid structure. Epoxy glue also has a resin in its composition, to which a catalyst is added during use.

2) The second factor is the size of the tile

The larger the tile, the heavier it is, which means that the thickness of the adhesive base should be greater. So, for a 10x10 tile, a layer of cement glue of 2 mm is required, for a 20x30 tile - 3 mm, for a 30x30 tile or more - 4-5 mm.

Measuring the thickness of the adhesive base is quite difficult. Even if it looks like a layer of glue will look even, in reality it may not be so. So, rely on the size of the spatula teeth. So, for a 30x30 cm tile, a spatula with 8 mm teeth is suitable. When applying glue, the spatula must be held at an angle of 90 degrees relative to the wall, then the thickness of the adhesive layer can be more accurate. For optimal distribution of glue, it must first be applied with a spatula without teeth and only then “comb” the adhesive base. Therefore, the consumption of glue also depends on the size of the spatula (this is often indicated in the instructions). So for example, if you use Ceresit CM12 adhesive, then the consumption will be 4.2 kg per square meter, provided that you use a spatula with 10 mm teeth for a 30x30 tile.

3) Type of tiles

Different types of tiles absorb different amounts of adhesive. Porcelain tiles absorb glue the least, glazed tiles a little more, and finally, the porous surface of cotto tiles absorbs the most glue, handmade tiles also absorb a lot of glue.

In addition, if the surface of the tile is uneven, then a small layer of glue should not be additionally applied, which will increase consumption.

4) Another factor on which the consumption of glue depends is the tile laying technology and the type of base

The ideal surface for laying tiles should be smooth, even and free of cracks. In this case, the consumption of glue is minimal, because. it is only necessary to ensure the adhesion of the tile to the surface.

If the surface has drops, cracks, then they are most often compensated by leveling with glue. There are specially designed adhesives that also level the wall, usually these are used if the difference in differences is not more than 3 cm. Such glue will also be needed for laying tiles that have differences on the back side, for example, for clinker.

Not only the back side of the tile has different porosity, but also the surface on which it is laid. The higher the porosity, the more the adhesive is absorbed. This means that additional costs will be required to securely fasten the tiles. For example, concrete walls absorb adhesive less than a cemented base.

5) No less important is the composition of the glue and the brand

The composition of the adhesive includes various additives that give it certain properties (frost resistance, etc.). Accordingly, these additives change the structure of the adhesive, make it liquid or vice versa thicker. Therefore, the consumption of glue of different brands, but of the same volume, may be different.

So for each type of glue and for glue of a certain brand there is a consumption rate. For example, for Eunice Granite glue, this norm is 1 kg, but for Litokol K80 glue, the norm is a little more - 1.35 kg.

6) Weather conditions also affect the technique of work

The optimum temperature for laying tiles varies between 18-25 degrees. But, the limits are much wider: from 5 to 38 degrees Celsius. The higher the room temperature. The more glue you will need, because. moisture evaporates very quickly. At sub-zero temperatures, the adhesive may generally lose its properties.

7) Glue consumption also depends on the technique of work, as well as the qualifications of the master

The amount of glue used depends on the technique of its application. So, when the spatula is tilted at an angle of 65 degrees, the consumption of glue will be greater than at 45 (the difference is 20-30%). The shape of the spatula can also play a significant role. It is most economical to work with a V-shaped spatula, in second place is a U-shaped spatula. More glue consumption falls on spatulas with square teeth. And of course, the glue consumption of an experienced craftsman will be clearly less than that of an amateur. So, if you are laying tiles for the first time, it is better to buy glue with a margin.

Glue Volume Calculation

There are several ways to calculate the required amount of glue.

Option one suitable for those who buy glue again, have already worked with it and know all the features of the consumption of glue of this brand. In this case, when buying a certain glue, you can go to the official website of the representative company. Very often, such sites offer a calculation option - a calculator. You only need to enter data on the size of the tile, the area of the room and the specific type of adhesive. You will receive the final answer in kilograms.

Second option. We offer you an approximate calculation of the consumption of cement-based adhesive. We take the most favorable conditions, the consumption of glue weighing 1.3 kg. We multiply this value by the thickness of the adhesive layer (let's say that the tile has dimensions of 30x30 cm, then the thickness of the adhesive layer will be 4 mm). We get the result: 5.2 per 1 square meter. Accordingly, if you need to lay out 10 squares, then you get a consumption of 52 kg. For tiles of other sizes, only the thickness of the adhesive base changes. However, this result can hardly be called accurate, if only because all adhesives are different. However, a rough estimate will give you some point of reference.

Option three- suitable for those who urgently need to find out how much glue is required per 1 m2.

For this, the following parameters are required: half the thickness of the tile (mm), the average consumption of the purchased adhesive. We multiply these figures and get the result. This method is the most inaccurate, because even porcelain tiles from the same batch have different thicknesses.

The most popular brands of glue: consumption rates

We bring to your attention the average consumption of glue per 1 square meter of the most popular, high-quality and sought-after brands in the construction industry.

To begin with, consider the general average indicators, where the first indicator is the adhesive consumption rate in kg per 1m2, and the second indicator is the thickness of the adhesive layer.

Clay Unix: 1-1.16 kg per 1 mm of glue

Glue Ceresit: 1.4-1.6 kg per 1 mm of glue / 1.5 - 6 kg per 2-8 mm

Glue Litokol: 1.3-1.5 kg per 1 mm of glue / 2.5-6 kg per 2-8 mm

Clay Hercules: 1.5 kg per 1 mm of glue

Glue Mapei: 1.2-1.6 kg per 1 mm glue / 2-8 kg per 2-8 mm

Well, now we bring to your attention the detailed results of the consumption of glue.

Let's start with the most popular - Eunice glue consumption for 1m2.

Eunice has been producing adhesives and other building mixtures for 20 years. Today, the company occupies a leading position in the sale of not only cement-based tile adhesives, but also other high-quality building mixtures.

Clay Eunice XXI

This adhesive is suitable for ceramic tiles, tiles, mosaics, porcelain stoneware, as well as natural stone slabs.

Clay Eunice 2000

This adhesive is also very popular and is suitable for laying any type of tile.

Consumption 1.16 kg per 1 square meter per 1 mm of glue / 3.5 kg per 6 mm of glue.

Glue UNIS Hi Tech

High tech adhesive.

Consumption 1.16 kg per 1 square meter per 1 mm of glue / 3.5 kg per 6 mm of glue.

Clay Eunice Plus

This adhesive is suitable for ceramic tiles, porcelain stoneware, mosaics.

Consumption 1.16 kg per 1 square meter per 1 mm of adhesive / 3.5 kg per 6 mm of adhesive

Clay Eunice Pool

This adhesive is specially designed for laying tiles in swimming pools and other water tanks.

Clay Eunice Granite

Tile adhesive of increased strength, suitable for heavy and large-sized tiles.

Tile adhesive for fastening large-format tiles made of natural stone and porcelain stoneware

Consumption 1 kg per 1 square meter per 1 mm of glue / 3.1 kg per 6 mm of glue.

Clay Belfix

This adhesive has a characteristic white color and is used for exterior and interior applications. Suitable for facing surfaces of ceramic, marble, granite tiles. It can also be used as a grout.

Glue UNIS FIX

Suitable for laying porcelain tiles and mosaics.

Consumption 1.16 kg per 1 square meter per 1 mm of glue.

Glue Ceresit

Glue Ceresit SM 9

Tile adhesive for interior work.

Consumption - 1.6 kg per 1 square meter per 1 mm of glue / 2 - 4.2 kg (the size of the spatula teeth and tile parameters are taken into account).

Glue Ceresit SM 11 Plus

This adhesive is designed for interior and exterior work with ceramic tiles, as well as for interior work with porcelain stoneware.

Consumption: 1.4-1.5 kg per 1 square meter per 1 mm of glue / 1.7 - 4.2 kg (taking into account the size of the spatula teeth and tile parameters).

Glue Ceresit SM 12

Floor tile adhesive, for large size tiles.

Consumption: 1.6 kg per 1 square meter per 1 mm of glue / 2.7 - 6 kg (taking into account the size of the spatula teeth and tile parameters).

Glue Ceresit CM 117

Suitable for facing stone, facade tiles. The adhesive is flexible.

Consumption: 1.4-1.5 kg per 1 square meter per 1 mm of glue / 1.8 - 4.7 kg (taking into account the size of the spatula teeth and tile parameters).

Glue Ceresit SM 16

It is an elastic tile adhesive, suitable for outdoor or indoor use.

Consumption: 1.55 kg per 1 square meter per 1 mm of glue / 1.5 - 3.2 kg (taking into account the size of the spatula teeth and the parameters of the tile).

Glue Ceresit SM 17

Highly elastic adhesive suitable for all types of work.

Consumption: 1.45 kg per 1 square meter per 1 mm of glue / 1.5 - 4.1 kg (taking into account the size of the spatula teeth and tile parameters).

Glue Ceresit CM 115

Suitable for marble tiles, glass mosaic. Adhesive for marble tiles and glass mosaics

Consumption: 1.5 kg per 1 square meter per 1 mm of glue / 2.5 - 4.4 kg (taking into account the size of the spatula teeth and tile parameters).

Calculation of Litokol glue consumption

Litokol is another popular tile adhesive from the Italian concern.

Cement-based adhesives (list below) are also produced in Russia.

Adhesive Litoflex K 81

The elastic cement mixture is suitable for laying ceramic tiles, as well as porcelain stoneware. Created on the basis of white cement.

Tile size. cm	Tooth size spatula. mm	Average consumption of glue, kg per m2
from 2x2 to 5x5

from 12x24.5 to 20x20
from 20x30 to 30x30
over 30x30

Adhesive Litoflex K 80

Highly adhesive elastic adhesive, suitable for laying tiles on underfloor heating, as well as ceramic and porcelain tiles.

Consumption: 1.35 kg per 1 square meter per 1 mm of adhesive.

Tile size. cm	Tooth size spatula. mm	Average consumption of glue, kg per m2
from 2x2 to 5x5

from 12x24.5 to 20x20
from 20x30 to 30x30
over 30x30

Glue Litoflex K80 eco

Adhesive cement mixture with a low level of dust formation. It has frost resistance, it is intended for ceramic, porcelain stoneware, as well as tiles made of natural stone.

Glue consumption: 2.5-5 kg per 1 square meter per 1 mm of glue.

Glue Litokol X 11

Frost-resistant adhesive of increased strength, for facing tiles.

Consumption: 1.35 kg per 1 square meter per 1 mm of adhesive.

Tile size. cm	Tooth size spatula. mm	Average consumption of glue, kg per m2
from 2x2 to 5x5

from 12x24.5 to 20x20
from 20x30 to 30x30
over 30x30

Adhesive Litofloor K66

Adhesive specially designed for thick layers. Suitable for floor ceramic, porcelain tiles.

Consumption: 1.5 kg per 1 square meter per 1 mm of glue. However, these data are approximate.

Adhesive Superflex K77

Suitable for facing large format tiles.

Consumption: 1.3 kg per 1 square meter per 1 mm of glue. Note that this adhesive is recommended to be applied to the tiles, for even greater strength, so the consumption will be increased.

Glue Litokol K 47

The mixture is intended for interior work: laying ceramic tiles on the floor.

Consumption: 1.3 kg per 1 square meter per 1 mm of glue.

Glue Litokol K 17

The adhesive is intended exclusively for ceramic tiles.

Consumption: 1.3 kg per 1 square meter per 1 mm of glue.

Dispersion based adhesives

Adhesive Litoacril Fix

Ready-made adhesive containing synthetic resins.

Glue Litoacril LA315

This adhesive belongs to the class D1TE. Has zero vertical slip, suitable for ceramic tiles.

Adhesive Litoacril Plus

Contains water based resins. The adhesive is ready to use and has a high slip resistance.

Glue Adesivo Universale LK78

The adhesive belongs to the class D1TE and is suitable for ceramic tiles.

Epoxy adhesives

Adhesive Litoelastic

Universal adhesive based on epoxy resins and polyurethane. Suitable for laying all tiles on various surfaces, including elastic ones.

Tile size. cm	Tooth size spatula. mm	Average consumption of glue, kg per m2




	10, double application
	10, double application
	10, double application

Epoxystuck X90

The mixture intended for filling the joints consists of epoxy resins, catalysts of organic origin. Suitable for ceramic tiles and natural stone tiles.

Tile size. cm	Tooth size spatula. mm	Average consumption of glue, kg per m2
clinker		1,16-1,86-2,33
		0,56-0,74-1,12
	3 – 4 – 6 – 8	0,33-0,43-0,65-0,87 0,45-0,60-0,89-1,19
		0,35-0,70-0,87

Clay Hercules

Glue from the company Hercules-Siberia is an excellent example of domestic construction mixtures of the highest quality.

Glue Hercules for tiles "Basic"

Suitable for facing walls made of brick, concrete, tiled, mosaic or ceramic tiles.

Consumption (by dry weight): 4.5 kg per 1 square meter per 3 mm of adhesive.

Clay Hercules for pools "AQUA///STOP"

Suitable for laying ceramic tiles in baths, pools, showers. Suitable for both indoor and outdoor work.

Glue Hercules for tiles and heavy plates "Strong"

Ideal for working with large size slabs of any type. The adhesive is suitable for both indoor and outdoor use on any surface.

Consumption (by dry weight): 5-8 kg per 1 square meter per 1 mm of adhesive.

More correct articles about tiles: Grout for ceramic tiles. Types and differences of grouts